ZTE MF971R SAR Test Plots: System Checks

System Check 750MHz

Communication System: UID 0, CW (0)

Frequency: 750 MHz

Medium parameters: f = 750 MHz; σ = 0.923 S/m; ε_r = 41.352; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(6.32, 6.32, 6.32) @ 750 MHz; Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 2.16 W/kg

Zoom Scan:

Measurement grid: dx=5mm, dy=5mm, dz=5mm

Reference Value: 41.00 V/m

Power Drift: 0.13 dB

Peak SAR (extrapolated): 3.26 W/kg

SAR(1 g): 2.06 W/kg

SAR(10 g): 1.37 W/kg

Maximum value of SAR (measured): 2.49 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

Note: SRTC performs system check by using 250mW at dipole antenna port.

System Check 835MHz

Communication System: UID 0, CW (0)

Frequency: 835 MHz

Medium parameters (interpolated): f = 835 MHz; σ = 0.911 S/m; ε_r = 40.266; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(6.16, 6.16, 6.16); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 2.72 W/kg

Zoom Scan:

Measurement grid: dx=5mm, dy=5mm, dz=5mm

Reference Value: 51.67 V/m

Power Drift: 0.08 dB

Peak SAR (extrapolated): 3.58 W/kg

SAR(1 g): 2.39 W/kg

SAR(10 g): 1.51 W/kg

Maximum value of SAR (measured): 2.75 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

Note: SRTC performs system check by using 250mW at dipole antenna port.

System Check 1800MHz

Communication System: UID 0, CW (0)

Frequency: 1800 MHz

Medium parameters: f = 1800 MHz; σ = 1.418 S/m; ε_r = 40.688; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(5.12, 5.12, 5.12); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 8.31 W/kg

Zoom Scan:

Measurement grid: dx=5mm, dy=5mm, dz=5mm

Reference Value: 76.60 V/m

Power Drift: 0.01 dB

Peak SAR (extrapolated): 17.5 W/kg

SAR(1 g): 9.49 W/kg

SAR(10 g): 4.97 W/kg

Maximum value of SAR (measured): 12.1 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

Note: SRTC performs system check by using 250mW at dipole antenna port.

System Check 2000MHz

Communication System: UID 0, CW (0)

Frequency: 2000 MHz

Medium parameters: f = 2000 MHz; σ = 1.427 S/m; ε_r = 39.844; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(5.03, 5.03, 5.03); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=10mm, dy=10mm

Maximum value of SAR (measured): 8.40 W/kg

Zoom Scan:

Measurement grid: dx=5mm, dy=5mm, dz=5mm

Reference Value: 76.22 V/m

Power Drift: 0.07 dB

Peak SAR (extrapolated): 18.7 W/kg

SAR(1 g): 9.82 W/kg

SAR(10 g): 4.96 W/kg

Maximum value of SAR (measured): 12.9 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

Note: SRTC performs system check by using 250mW at dipole antenna port.

System Check 2450MHz

Communication System: UID 0, CW (0)

Frequency: 2450 MHz

Medium parameters: f = 2450 MHz; σ = 1.866 S/m; ε_r = 38.343; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(4.58, 4.58, 4.58); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection), z = -3.0, 32.0
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=12mm, dy=12mm

Maximum value of SAR (measured): 21.2 W/kg

Zoom Scan:

Measurement grid: dx=5mm, dy=5mm, dz=5mm

Reference Value: 108.3 V/m

Power Drift: 0.19 dB

Peak SAR (extrapolated): 28.2 W/kg

SAR(1 g): 13.5 W/kg

SAR(10 g): 6.14 W/kg

Maximum value of SAR (measured): 22.6 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

Note: SRTC performs system check by using 250mW at dipole antenna port.

System Check 2600MHz

Communication System: UID 0, CW (0)

Frequency: 2600 MHz

Duty Cycle: 1:1

Medium parameters: f = 2600 MHz; σ = 1.951 S/m; ε_r = 39.672; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(4.37, 4.37, 4.37) @ 2600 MHz; Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=12mm, dy=12mm

Maximum value of SAR (measured): 22.7 W/kg

Zoom Scan:

Measurement grid: dx=5mm, dy=5mm, dz=5mm

Reference Value: 102.2 V/m

Power Drift: 0.11 dB

Peak SAR (extrapolated): 33.7 W/kg

SAR(1 g): 14.1 W/kg

SAR(10 g): 6.52 W/kg

Maximum value of SAR (measured): 26.6 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

Note: SRTC performs system check by using 250mW at dipole antenna port.

System Check 5200MHz

Communication System: UID 0, CW (0)

Frequency: 5200 MHz

Medium parameters: f = 5200 MHz; σ = 4.734 S/m; ε_r = 37.691; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: EX3DV4 - SN3985; ConvF(5.65, 5.65, 5.65); Calibrated: 2020/5/20
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=10mm, dy=10mm

Maximum value of SAR (measured): 1.86 W/kg

Zoom Scan:

Measurement grid: dx=4mm, dy=4mm, dz=2mm

Reference Value: 21.92 V/m

Power Drift: 0.12 dB

Peak SAR (extrapolated): 3.29 W/kg

SAR(1 g): 0.782 W/kg

SAR(10 g): 0.231 W/kg

Maximum value of SAR (measured): 1.98 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

Note: SRTC performs system check by using 10mW at dipole antenna port.

System Check 5800MHz

Communication System: UID 0, CW (0)

Frequency: 5800 MHz

Medium parameters: f = 5800 MHz; σ = 5.495 S/m; ε_r = 36.774; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: EX3DV4 - SN3985; ConvF(4.95, 4.95, 4.95); Calibrated: 2020/5/20
Sensor-Surface: 1.4mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.10 (2); SEMCAD X Version 14.6.13 (7474)

Area Scan:

Measurement grid: dx=10mm, dy=10mm

Maximum value of SAR (measured): 2.07 W/kg

Zoom Scan:

Measurement grid: dx=4mm, dy=4mm, dz=2mm

Reference Value: 21.65 V/m

Power Drift: 0.14 dB

Peak SAR (extrapolated): 4.17 W/kg

SAR(1 g): 0.799 W/kg

SAR(10 g): 0.225 W/kg

Maximum value of SAR (measured): 1.81 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

Note: SRTC performs system check by using 10mW at dipole antenna port.

GSM850 System Check

Body-wron&Hotspot: Back

Communication System: UID 0, Generic GSM (0)

Frequency: 836.6 MHz

Duty Cycle: 3:8.30042

Medium parameters (interpolated): f = 836.6 MHz; σ = 0.905 S/m; ε_r = 41.528; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(6.16, 6.16, 6.16); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 0.330 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 16.54 V/m

Power Drift: -0.04 dB

Peak SAR (extrapolated): 0.441 W/kg

SAR(1 g): 0.297 W/kg

SAR(10 g): 0.197 W/kg

Maximum value of SAR (measured): 0.344 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

GSM1900 System Check

Body-wron&Hotspot: Back

Communication System: UID 0, Generic GSM (0)

Frequency: 1880 MHz

Duty Cycle: 3:8.30042

Medium parameters (interpolated): f = 1880 MHz; σ = 1.4 S/m; ε_r = 40; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(5.12, 5.12, 5.12); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 0.318 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 8.136 V/m

Power Drift: 0.04 dB

Peak SAR (extrapolated): 0.545 W/kg

SAR(1 g): 0.317 W/kg

SAR(10 g): 0.180 W/kg

Maximum value of SAR (measured): 0.391 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

WCDMA Band II System Check

Body-wron&Hotspot: Back

Communication System: UID 0, WCDMA BAND2 (0)

Frequency: 1880 MHz

Duty Cycle: 1:1

Medium parameters (interpolated): f = 1880 MHz; σ = 1.4 S/m; ε_r = 40; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(5.12, 5.12, 5.12); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 0.975 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 14.71 V/m

Power Drift: 0.01 dB

Peak SAR (extrapolated): 1.36 W/kg

SAR(1 g): 0.819 W/kg

SAR(10 g): 0.470 W/kg

Maximum value of SAR (measured): 0.965 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

WCDMA Band V System Check

Body-wron&Hotspot: Front

Communication System: UID 0, WCDMA BAND 5 (0)

Frequency: 836.6 MHz

Duty Cycle: 1:1

Medium parameters (interpolated): f = 836.6 MHz; σ = 0.905 S/m; ε_r = 41.528; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(6.16, 6.16, 6.16); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 0.761 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 24.51 V/m

Power Drift: 0.05 dB

Peak SAR (extrapolated): 0.944 W/kg

SAR(1 g): 0.675 W/kg

SAR(10 g): 0.474 W/kg

Maximum value of SAR (measured): 0.763 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

LTE Band 2 System Check

Body-wron&Hotspot: Back

Communication System: UID 0, LTE band 02 (0)

Frequency: 1900 MHz

Duty Cycle: 1:1

Medium parameters: f = 1900 MHz; σ = 1.4 S/m; ε_r = 40; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(5.12, 5.12, 5.12); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 0.789 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 11.32 V/m

Power Drift: 0.07 dB

Peak SAR (extrapolated): 1.22 W/kg

SAR(1 g): 0.748 W/kg

SAR(10 g): 0.435 W/kg

Maximum value of SAR (measured): 0.899 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

LTE Band 4 System Check

Body-wron&Hotspot: Back

Communication System: UID 0, LTE band 4 (0)

Frequency: 1720 MHz

Duty Cycle: 1:1

Medium parameters (interpolated): f = 1720 MHz; σ = 1.368 S/m; ε_r = 40.092; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(5.12, 5.12, 5.12); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 0.688 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 13.34 V/m

Power Drift: 0.14 dB

Peak SAR (extrapolated): 0.959 W/kg

SAR(1 g): 0.583 W/kg

SAR(10 g): 0.345 W/kg

Maximum value of SAR (measured): 0.704 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

LTE Band 5 System Check

Body-wron&Hotspot: Front

Communication System: UID 0, LTE Band 5 (0)

Frequency: 836.5 MHz

Duty Cycle: 1:1

Medium parameters (interpolated): f = 836.5 MHz; σ = 0.905 S/m; ε_r = 41.528; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(6.16, 6.16, 6.16); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=15mm, dy=15mm

Maximum value of SAR (measured): 0.786 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 23.01 V/m

Power Drift: 0.01 dB

Peak SAR (extrapolated): 1.02 W/kg

SAR(1 g): 0.723 W/kg

SAR(10 g): 0.503 W/kg

Maximum value of SAR (measured): 0.825 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

LTE Band 7 System Check

Body-wron&Hotspot: Back

Communication System: UID 0, LTE Band 7 (0)

Frequency: 2510 MHz

Duty Cycle: 1:1

Medium parameters (interpolated): f = 2510 MHz; σ = 1.861 S/m; ε_r = 39.117; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(4.58, 4.58, 4.58); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=12mm, dy=12mm

Maximum value of SAR (measured): 1.10 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 10.10 V/m

Power Drift: 0.20 dB

Peak SAR (extrapolated): 1.75 W/kg

SAR(1 g): 0.949 W/kg

SAR(10 g): 0.528 W/kg

Maximum value of SAR (measured): 1.17 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

LTE Band 40 System Check

Body-wron&Hotspot: Back

Communication System: UID 0, LTE band 40 (0)

Frequency: 2355 MHz

Duty Cycle: 1:1.58

Medium parameters (interpolated): f = 2355 MHz; σ = 1.713 S/m; ε_r = 39.347; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(4.74, 4.74, 4.74); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=12mm, dy=12mm

Maximum value of SAR (measured): 0.429 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 8.079 V/m

Power Drift: 0.13 dB

Peak SAR (extrapolated): 0.680 W/kg

SAR(1 g): 0.374 W/kg

SAR(10 g): 0.207 W/kg

Maximum value of SAR (measured): 0.459 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

LTE Band 41 System Check

Body-wron&Hotspot: Back

Communication System: UID 0, LTE Band 41 (0)

Frequency: 2593 MHz

Duty Cycle: 1:1.58

Medium parameters (interpolated): f = 2593 MHz; σ = 1.952 S/m; ε_r = 39.009; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(4.37, 4.37, 4.37); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=12mm, dy=12mm

Maximum value of SAR (measured): 0.513 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 6.470 V/m

Power Drift: 0.18 dB

Peak SAR (extrapolated): 0.774 W/kg

SAR(1 g): 0.434 W/kg

SAR(10 g): 0.245 W/kg

Maximum value of SAR (measured): 0.525 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

WIFI 2.4GHz System Check

Body-wron&Hotspot: Front

Communication System: UID 0, WIFI 2.4GHz (0)

Frequency: 2437 MHz

Duty Cycle: 1:1.01

Medium parameters (interpolated): f = 2437 MHz; σ = 1.788 S/m; ε_r = 39.219; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: ES3DV3 - SN3127; ConvF(4.58, 4.58, 4.58); Calibrated: 2020/9/1
Sensor-Surface: 3mm (Mechanical Surface Detection)
Electronics: DAE4 Sn720; Calibrated: 2020/09/30
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=12mm, dy=12mm

Maximum value of SAR (measured): 0.236 W/kg

Zoom Scan:

Measurement grid: dx=8mm, dy=8mm, dz=5mm

Reference Value: 6.995 V/m

Power Drift: -0.04 dB

Peak SAR (extrapolated): 0.377 W/kg

SAR(1 g): 0.186 W/kg

SAR(10 g): 0.099 W/kg

Maximum value of SAR (measured): 0.227 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

WIFI 5G System Check

Hotspot: Top

Communication System: UID 0, 802.11nHT 40(MCS0) (0)

Frequency: 5190 MHz

Duty Cycle: 1:1.11

Medium parameters: f = 5190 MHz; σ = 4.676 S/m; ε_r = 34.965; ρ = 1000 kg/m³

Phantom section: Flat Section

DASY5 Configuration:

Probe: EX3DV4 - SN3985; ConvF(5.65, 5.65, 5.65); Calibrated: 2020/5/20
Sensor-Surface: 1.41mm (Mechanical Surface Detection)
Electronics: DAE4 Sn755; Calibrated: 2020/5/6
Phantom: 1659; Type: QD 000 P40 CD; Serial: xxxx
Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7373)

Area Scan:

Measurement grid: dx=10mm, dy=10mm

Maximum value of SAR (measured): 0.627 W/kg

Zoom Scan:

Measurement grid: dx=4mm, dy=4mm, dz=2mm

Reference Value: 9.536 V/m

Power Drift: 0.12 dB

Peak SAR (extrapolated): 0.484 W/kg

SAR(1 g): 0.491 W/kg

SAR(10 g): 0.237 W/kg

Maximum value of SAR (measured): 0.783 W/kg

A visual representation of the Specific Absorption Rate (SAR) distribution shows a central hot spot.

	ZTE MF971R LTE Ufi WLAN Compliance Test Report Official test report detailing the WLAN performance and FCC compliance of the ZTE MF971R LTE Ufi mobile hotspot, including conducted and radiated emissions testing.
	ZTE MF971R Mobile Hotspot External Photos and Component Details Comprehensive external photographs and component specifications for the ZTE MF971R mobile hotspot, including FCC ID SRQ-MF971R, battery, charger, and USB cable details.
	ZTE MF971R LTE Ufi Channel Limitation Declaration Official declaration from ZTE Corporation concerning firmware-based operating channel limitations for the MF971R LTE Ufi mobile hotspot in the US and Canada markets.
	ZTE Blade A5 2020 SAR Test Report This report details the Specific Absorption Rate (SAR) test results for the ZTE Blade A5 2020 mobile phone, conducted by TA Technology (Shanghai) Co., Ltd. It covers compliance with FCC regulations and IEEE standards for human exposure to radiofrequency electromagnetic fields.
	MF971R Kratka navodila - ZTE Mobilni Dostopnik Navodila za namestitev, uporabo in odpravljanje težav z mobilnim dostopnikom ZTE MF971R. Vključuje informacije o povezljivosti, indikatorskih lučkah, varnosti, specifikacijah in izjavi o skladnosti.
	MF971R Quick Start Guide - ZTE This guide provides quick start instructions for the ZTE MF971R mobile hotspot, covering device appearance, indicator lights, connection scenarios, SIM card installation, Wi-Fi and USB connections, configuration, troubleshooting, SAR information, specifications, safety warnings, and warranty.
	ZTE MF971R Quick Start Guide A comprehensive guide to setting up and using the ZTE MF971R mobile hotspot, covering device appearance, indicator lights, SIM card installation, Wi-Fi and USB connections, internet access, PC configuration, and safety information.
	ZTE MF971R LTE CAT 6 4G+ Mobile Broadband Hotspot Explore the ZTE MF971R, a powerful LTE CAT 6 mobile broadband hotspot offering speeds up to 300Mbps, a 2000mAh battery, and support for up to 32 devices. Ideal for on-the-go connectivity.