Hewlett Packard 730 Series Campus Access Points Installation Guide

Installation Guide for Hewlett Packard models including: APIN0734, Q9DAPIN0734, 730 Series Campus Access Points, 730 Series, Campus Access Points, Access Points

HPE Aruba Networking 730 Series Campus Access Points Installation Guide

AP-73x Install Guide EN v2

Hewlett Packard Enterprise Company APIN0734 ACCESS POINT Q9DAPIN0734 Q9DAPIN0734 apin0734

File Info : application/pdf, 25 Pages, 1.73MB

GetApplicationAttachment.html?id=8167351

HPE Aruba Networking
730 Series Campus Access Points
Installation Guide

Copyright Information
© Copyright 2025 Hewlett Packard Enterprise Development LP.
Open Source Code
This product includes code licensed under certain open source licenses which require source compliance. The corresponding source for these components is available upon request. This offer is valid to anyone in receipt of this information and shall expire three years following the date of the final distribution of this product version by Hewlett Packard Enterprise Company. To obtain such source code, please check if the code is available in the HPE Software Center at https://myenterpriselicense.hpe.com/cwp-ui/software but, if not, send a written request for specific software version and product for which you want the open source code. Along with the request, please send a check or money order in the amount of US $10.00 to:
Hewlett Packard Enterprise Company Attn: General Counsel WW Corporate Headquarters 1701 E Mossy Oaks Rd, Spring, TX 77389 United States of America.

HPE Aruba Networking 730 Series Campus Access Points | Installation Guide

Edition 1 | April 2025

Contents About This Guide
Guide Overview Related Documentation Contacting Support
Hardware Overview
Package Contents Access Point Overview LEDs USB-A Ports Reset Button Micro-B Console Port Ethernet Ports Kensington Lock Slot Power BLE Radio Default State Console Port Default State USB Host Interface Default State
Installation
Pre-Installation Checklist Identifying Specific Installation Locations Identifying Known RF Absorbers/Reflectors/ Interference Sources Access Point Installation Software Verifying Post-Installation Connectivity
Specifications, Safety, and Compliance
Electrical Environmental Regulatory Model Name Brazil Canada EAC European Union and United Kingdom India Medical Mexico Taiwan Thailand Ukraine United States Proper Disposal of HPE Aruba Networking Equipment
HPE Aruba Networking 730 Series Campus Access Points

Contents
Contents
1 2
2 2 2
3
3 3 7 8 9 9 10 10 10 10 10 10
11
11 11 11 12 13 13
14
14 14 14 15 15 16 16 17 17 18 18 19 19 19 21
1

Chapter 1 About This Guide

About This Guide
This document describes the hardware features of the HPE Aruba Networking 730 Series Campus Access Points. It provides a detailed overview of the physical and performance characteristics of each access point model and explains how to install the access point.

Guide Overview
n Hardware Overview provides a detailed hardware overview of the HPE Aruba Networking 730 Series Campus Access Points .
n Installation describes how to install the HPE Aruba Networking 730 Series Campus Access Points. n Specifications, Safety, and Compliance lists the HPE Aruba Networking 730 Series Campus Access
Points's technical specifications, safety, and regulatory compliance information.

Related Documentation
You require the following documents for the complete management of HPE Aruba Networking 730 Series Campus Access Points.
n Latest document of the software user guide: https://www.arubanetworks.com/techdocs/ArubaDocPortal/content/cons-aos-home.htm
n CLI bank: https://www.arubanetworks.com/techdocs/CLI-Bank/Content/Home.htm

Contacting Support

Table 1: Contact Information

Main Site

arubanetworks.com

Support Site

https://networkingsupport.hpe.com/home

Airheads Social Forums and Knowledge community.arubanetworks.com Base

North American Telephone

1-800-943-4526 (Toll Free) 1-408-754-1200

International Telephone

arubanetworks.com/support-services/contact-support/

Software Licensing Site

lms.arubanetworks.com

End-of-life Information

arubanetworks.com/support-services/end-of-life/

Security Incident Response Team

Site: arubanetworks.com/support-services/security-bulletins/ Email: aruba-sirt@hpe.com

HPE Aruba Networking 730 Series Campus Access Points

Chapter 2 Hardware Overview

Hardware Overview
The HPE Aruba Networking 730 Series Campus Access Points support the IEEE 802.11be (Wi-Fi 7) WLAN standard, while also supporting IEEE 802.11a/b/g/n/ac/ax wireless services.

Package Contents
Inform your supplier to check if there are any incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed.

Table 2: Package Contents Item

Quantity

HPE Aruba Networking 730 Series Campus Access Point

Console adapter cable (in eco-friendly 5-packs only)

Access Point Overview
Figure 1 AP-734/AP-734A Front View

HPE Aruba Networking 730 Series Campus Access Points

System Status LED

2 GHz Radio Status LED

5 GHz Radio Status LED

6 GHz Radio Status LED

External Antenna Connectors
The AP-734/AP-734A access point has two sets of two external RP-SMA female antenna connectors.
n First set (labeled as A0 and A1): 2.4GHz and 5GHz n Second set (labeled as B0 and B1): 6GHz

External antennas for this device must be installed by a professional installer, using manufacturer-approved antennas only. The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the regulatory limit set by the host country/domain. Installers are required to record the antenna gain for this device in the system management software. A list of approved antennas can be found in the ordering guide at https://www.arubanetworks.com
Les antennes externes pour cet appareil doivent être installées par un professionnel agréé, en utilisant uniquement des antennes approuvées par le fabricant. Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine. Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système. Une liste d'antennes approuvées peut être trouvée à https://www.arubanetworks.com

HPE Aruba Networking 730 Series Campus Access Points | 4

Figure 2 AP-735/AP-735A Front View

System Status LED

2 GHz Radio Status LED

5 GHz Radio Status LED

6 GHz Radio Status LED

HPE Aruba Networking 730 Series Campus Access Points

Figure 3 AP-735/AP-735A Back View

USB-A Port (U0)

USB-A Port (U1)

Reset Button

Micro-B Console Port

E0 Ethernet Port

E1 Ethernet Port

Kensington Lock Slot

DC Power Port

The ports on the back of the AP-734/AP-734A access point are the same as the ones of the AP-735/AP-735A access point.

HPE Aruba Networking 730 Series Campus Access Points | 6

LEDs
The LED indicators provide the system and radio status of the access point.

Table 3: System, 2 GHz, 5 GHz and 6 GHz LEDs

LEDs

Color/State

Meaning

SYS

Off Blinking1 - Green

AP Powered off AP booting, not ready

On - Green Flashing off2 - Green On - Amber Flashing off2 - Amber
flashing on3 - Green

AP ready, fully functional, no network restrictions
AP ready, fully functional, uplink negotiated in sub-optimal speed (< 1 Gbps)
AP ready, restricted power mode (limited PoE power available, or IPM restrictions applied), no network restrictions
AP ready, restricted power mode (limited PoE power available, or IPM restrictions applied), uplink negotiated in sub-optimal speed (< 1 Gbps)
AP in deep-sleep mode

2 GHz 5 GHz

On - Red
Off On - Green On - Amber
On - Blue Off On - Green On - Amber
On - Blue Alternate4

System error condition - Immediate attention required
AP powered off, or radio/band disabled
Radio enabled in access (AP) mode
Radio enabled in monitor or spectrum analysis mode
Radio enabled in uplink or mesh mode
AP powered off, or radio disabled
Radio enabled in access (AP) mode
Radio enabled in monitor or spectrum analysis mode
Radio enabled in uplink or mesh mode
Dual-5GHz mode; colors indicate mode per radio

HPE Aruba Networking 730 Series Campus Access Points

LEDs 6 GHz

Color/State Off On - Green On - Amber
On - Blue Alternate4

Meaning
AP powered off, or radio disabled
Radio enabled in access (AP) mode
Radio enabled in monitor or spectrum analysis mode
Radio enabled in uplink or mesh mode
Dual-6GHz mode; colors indicate mode per radio

1. Blinking: one second on, one second off, 2 seconds cycle. 2. Flashing off: mostly on, fraction of a second off, 2 seconds cycle. 3. Flashing on: mostly off, fraction of a second on, 2 seconds cycle. 4. One second for first radio mode, fraction of a second off, one second for second radio mode.
LED Display Settings
The LEDs have three operating modes that can be selected in the system management software:
n Normal mode: refer to Table 3 n All LEDs off n Blink mode: all LEDs blink green (synchronized). One second on, one second off, 2 seconds cycle.
A short press of the reset button during normal operation toggles the LED mode between "normal" and "off".

USB-A Ports
The two USB-A ports support USB 2.0 standard, and are compatible with selected cellular modems and other peripherals. When active, the two USB-A ports can supply up to 10W/2A of combined power to attached devices.
To secure a USB device to the access point, tighten the USB security screw after the USB device is plugged into the USB interface.

HPE Aruba Networking 730 Series Campus Access Points | 8

Figure 4 USB Security Screw

Reset Button
Use one of the following methods to reset the access point to factory default settings:
n During normal operation of the AP (system LED solid): hold the reset button for at least 10 seconds, release the reset button.
n During power up of the AP: hold the reset button for at least 20 seconds after powering up the AP, release the reset button.
Micro-B Console Port
The console port is a Micro-B connector located on the back of the access point. Use the proprietary APCBL-SERU cable (sold separately) for direct management of the access point when connected to a serial terminal or laptop.
Figure 5 Micro-B Console Port Pin-out
1: NC 2: RXD 3: TXD 4: GND 5: GND

HPE Aruba Networking 730 Series Campus Access Points

Ethernet Ports
The access point is equipped with two Ethernet ports (E0 and E1). Both ports are 100/1000/2500/5000 Base-T auto-sensing MDI/MDIX, supporting 802.3af, 802.3at or 802.3bt Power over Ethernet compliance to accept power from a POE source.
Kensington Lock Slot
The AP is equipped with a Kensington lock slot for additional physical security.
Power
Both E0 and E1 ports support PoE-in (AP is a PoE-PD device), allowing the AP to draw power from a compliant PoE power source. If PoE is not available, a proprietary AP-AC2-12B power adapter (sold separately) can be used to power the access point. When both PoE and DC power sources are available, the DC power source takes precedence. In that case, the access point simultaneously draws a minimal current from the PoE source. In the event that the DC source fails, the access point switches to the PoE sources.
n When powered by DC, 802.3bt (class 5), the AP will operate without restrictions. n When powered by 802.3at (class 4) PoE with the Intelligent Power Monitoring (IPM) feature disabled,
the AP will disable the USB port.
BLE Radio Default State
When the access point is in factory default state the integrated BLE radio is enabled. This applies to the non-TAA product SKUs only. On the TAA products, the BLE radio is disabled when the unit is in factory default conditions. Once the AP has established a connection with its management platform, the BLE radio state is updated to match what's configured there. This state is maintained if the AP is powercycled or rebooted.
Console Port Default State
When the access point is in factory default state the console interface (both physical port and BLE) is enabled with default credentials (username is "admin" and password is the serial number of the unit). Once the AP has established a connection with its management platform, the console port state (enabled/disabled) and access credentials are updated to match what's configured there. State and credentials are maintained if the AP is power-cycled or rebooted.
USB Host Interface Default State
When the access point is in factory default state the USB host interface is powered and enabled, assuming the AP is not in a restricted power mode. On some AP models the USB port may be disabled when a POE source with insufficient power budget is used. Once the AP has established a connection with its management platform, the USB host interface state is updated to match what's configured there. This state is maintained if the AP is power-cycled or rebooted.
HPE Aruba Networking 730 Series Campus Access Points | 10

Chapter 3 Installation

Installation
Pre-Installation Checklist
Before installing the access point, be sure that you have the following: n A mount kit compatible with the AP and mount surface n One or two Cat5E or better UTP cables with network access n Compatible antenna(s) when installing AP-734/AP-734A Some optional items: n A compatible power adapter with power cord n A compatible PoE midspan injector with power cord n An AP-CBL-SERU console cable Also, make sure at least one of the following network services is supported: n HPE Aruba Networking Discovery Protocol (ADP) n DNS server with an "A" record n DHCP Server with vendor specific options
Access points are radio transmission devices and as such are subject to governmental regulation. Network administrators responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access points must use channel assignments appropriate to the location in which the access point will be used.

Identifying Specific Installation Locations
Use the access point placement map generated by HPE Aruba Networking RF Plan software application to determine the proper installation location(s). Each location should be as close as possible to the center of the intended coverage area and should be free from obstructions or obvious sources of interference. These RF absorbers/reflectors/interference sources will impact RF propagation and should be accounted for during the planning phase and adjusted for in RF plan.
Identifying Known RF Absorbers/Reflectors/ Interference Sources
Identifying known RF absorbers, reflectors, and interference sources while in the field during the installation phase is critical. Make sure that these sources are taken into consideration when you attach

HPE Aruba Networking 730 Series Campus Access Points

an access point to its fixed location. RF absorbers include: n Cement/concrete--Old concrete has high levels of water dissipation, which dries out the concrete,
allowing for potential RF propagation. New concrete has high levels of water concentration in the concrete, blocking RF signals. n Natural Items--Fish tanks, water fountains, ponds, and trees n Brick RF reflectors include: n Metal Objects--Metal pans between floors, rebar, fire doors, air conditioning/heating ducts, mesh windows, blinds, chain link fences (depending on aperture size), refrigerators, racks, shelves, and filing cabinets. n Do not place an access point between two air conditioning/heating ducts. Make sure that access points are placed below ducts to avoid RF disturbances. RF interference sources include: n Other Wi-Fi networks n Microwave ovens n Bluetooth devices
Access Point Installation
The HPE Aruba Networking 730 Series Campus Access Points are designed for ceiling, or wall mounted deployments. HPE Aruba Networking provides several mount kits to use with the access points. These mount kits are available as accessories and must be ordered separately. Refer to the HPE Aruba Networking 730 Series Campus Access Points ordering guide at https://www.arubanetworks.com.
n All HPE Aruba Networking access points should be professionally installed by a professional installer. The installer is responsible for ensuring that grounding is available and meets applicable national and electrical codes. Failure to properly install this product may result in physical injury and/or damage to property.
n Tous les points d'accès HPE Aruba Networking doivent impérativement être installés par un professionnel agréé. Ce dernier doit s'assurer que l'appareil est mis à la terre et que le circuit de mise à la terre est conforme aux codes électriques nationaux en vigueur. Le fait de ne pas installer correctement ce produit peut entraîner des blessures corporelles et / ou des dommages matériels.
For indoor use only. The access point, AC adapter, and all connected cables are not to be installed outdoors. This stationary device is intended for stationary use in partly temperature controlled weather-protected environments (class 3.2 per ETSI 300 019).
HPE Aruba Networking 730 Series Campus Access Points | 12

Software
For instructions on choosing operating modes and initial software configuration, refer to the AP Software Quick Start Guide .
HPE Aruba Networking access points are classified as radio transmission devices, and are subject to government regulations of the host country. The network administrator(s) is/are responsible for ensuring that configuration and operation of this equipment is in compliance with their country's regulations. For a complete list of approved channels in your country, refer to the HPE Aruba Networking Downloadable Regulatory Table.
Verifying Post-Installation Connectivity
The integrated LED on the access point can be used to verify that the access point access point is receiving power and initializing successfully. Refer to the AP Software Quick Start Guide for further details on verifying post-installation network connectivity.

HPE Aruba Networking 730 Series Campus Access Points

Chapter 4
Specifications, Safety, and Compliance
Specifications, Safety, and Compliance
This chapter provides an overview of the HPE Aruba Networking 730 Series Campus Access Points specifications, safety, and compliance information.
Electrical
n Ethernet o E0 and E1 ports: 100/1000/2500/5000 Base-T auto-sensing MDI/MDX wired RJ45 network connectivity port, supporting 802.3at or 802.3bt Power over Ethernet compliance .
n Power o 12V DC power interface, support powering through AC-to-DC power adapter o PoE-PD: 802.3at or 802.3bt PoE
Environmental
n Operating o Temperature: 0°C to +50°C (+32°F to +122°F) o Relative Humidity: 5% to 95%
n Storage o Temperature: -25°C to +55°C (-13°F to +131°F) o Relative Humidity: 10% - 100%
n Transportation o Temperature: -40°C to +70°C (-40°F to +158°F) o Relative Humidity: up to 95%
For additional specifications on this product, please refer to the HPE Aruba Networking 730 Series Campus Access Points data sheet.
Regulatory Model Name
For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number (RMN). The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number. The regulatory model number RMN is not the marketing name or model number of the product. The regulatory model name for the HPE Aruba Networking 730 Series Campus Access Points:
n AP-734 RMN: APIN0734 n AP-735 RMN: APIN0735

HPE Aruba Networking 730 Series Campus Access Points

n AP-734A RMN: APIN0734A n AP-735A RMN: APIN0735A
Brazil
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Para mais informações, consulte o site da Anatel: https://www.gov.br/anatel/pt-br O uso deste equipamento é restrito a ambientes fechados e proibido em plataformas petrolíferas, carros, trens, embarcações e no interior de aeronaves abaixo de 3.048 m (10.000 pés).
Canada
Innovation, Science and Economic Development Canada
This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. When operated in the 5.15 to 5.25 GHz frequency range, this device is restricted to indoor use to reduce the potential for harmful interference with co-channel Mobile Satellite Systems.
n Operation shall be limited to indoor use only. n Operation on oil platforms, cars, trains, boats, and aircraft shall be prohibited except for on large aircraft
flying above 10,000 feet. n Devices shall not be used for control of or communications with unmanned aircraft systems.
Innovation, Sciences et Développement économique Canada
Cet appareil numérique de Classe B répond à toutes les exigences de la réglementation canadienne sur le matériel brouilleur. Cet appareil contient des émetteurs / récepteurs exemptés de licence qui sont conformes aux RSS exempts de licence d'Innovation, Sciences et Développement économique Canada. Son fonctionnement est soumis aux deux conditions suivantes: (1) ce périphérique ne doit pas provoquer d'interférences, et (2) ce périphérique doit accepter toute interférence, y compris les interférences susceptibles de provoquer un dysfonctionnement. Pour un fonctionnement dans la bande de fréquences comprises entre 5,15 et 5,25 GHz, son utilisation est limitée à un environnement intérieur afin de réduire la possibilité d'interférences nuisibles avec les systèmes mobiles par satellite opérant sur le même canal.
HPE Aruba Networking 730 Series Campus Access Points | 15

n Le fonctionnement est restreint à une utilisation à l'intérieur seulement.
n L'utilisation sur les plateformes pétrolières ou dans les voitures, les trains, les bateaux et les avions est interdite, à l'exception des gros avions volant à plus de 3 km (10 000 pi).
n Cet appareil ne doit pas être utilisé pour le contrôle ou pour la communication avec des systèmes de drones.

EAC

TOO «- ()», , 050040, . , , -, 77/7, /: + 7 727 355 35 50 «- ()», , 050040, ., , , 77/7, /: +7 727 355 35 50

European Union and United Kingdom
The Declaration of Conformity made under Radio Equipment Directive 2014/53/EU as well as the United Kingdom's Radio Equipment Regulations 2017/UK is available for viewing below. Select the document that corresponds to your device's model number as it is indicated on the product label.
EU & UK Declaration of Conformity
Wireless Channel Restrictions
5150-5350MHz band is limited to indoor only in the following countries; Austria (AT), Belgium (BE), Bulgaria (BG), Croatia (HR), Cyprus (CY), Czech Republic (CZ), Denmark (DK), Estonia (EE), Finland (FI), France (FR), Germany (DE), Greece (GR), Hungary (HU), Iceland (IS), Ireland (IE), Italy (IT), Latvia (LV), Liechtenstein (LI), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Norway (NO), Poland (PL), Portugal (PT), Romania (RO), Serbia (RS), Slovakia (SK), Slovenia (SL), Spain (ES), Sweden (SE), Switzerland (CH), Turkey (TR), United Kingdom (UK (NI)).

Radio BLE/Zigbee

Frequency Range 2402-2480 MHz

Max EIRP 9 dBm

HPE Aruba Networking 730 Series Campus Access Points

Radio Wi-Fi

Frequency Range 2412-2472 MHz 5150-5250 MHz 5250-5350 MHz 5470-5725 MHz 5725-5850 MHz 5945-6425 MHz

Max EIRP 20 dBm 23 dBm 23 dBm 30 dBm 14 dBm 23 dBm

India
This product conforms to the relevant Essential Requirements of TEC, Department of Telecommunications, Ministry of Communications, Govt of India, New Delhi-110001
Medical
1. Equipment not suitable for use in the presence of flammable mixtures. 2. Connect to only IEC 62368-1 or IEC 60601-1 certified products and power sources. The end user is
responsible for the resulting medical system complies with the requirements of IEC 60601-1. 3. Wipe with a dry cloth, no additional maintenance required. 4. No serviceable parts, the unit must be sent back to the manufacturer for repair. 5. No modifications are allowed without approval from HPE Aruba Networking.
n Use of this equipment adjacent to or stacked with other equipment should be avoided because it could result in improper operation. If such use is necessary, this equipment and the other equipment should be observed to verify that they are operating normally.
n Use of accessories, transducers and cables other than those specified or provided by the manufacturer of this equipment could result in increased electromagnetic emissions or decreased electromagnetic immunity of this equipment and result in improper operation.
n Portable RF communications equipment (including peripherals such as antenna cables and external antennas) should be used no closer than 30 cm (12 inches) to any part of the access point. Otherwise, degradation of the performance of this equipment could result.
HPE Aruba Networking 730 Series Campus Access Points | 17

n This device is intended for indoor use in professional healthcare facilities. n This device has no IEC/EN60601-1-2 essential performance. n Compliance is based on the use of HPE Aruba Networking approved accessories. Refer to the ordering
guide for this access point at https://www.arubanetworks.com
Mexico
La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.
Taiwan
1. 2. 3. MPE 1 mW/cm2
(Applicant): (Address):11568 6610 1 (TEL): (02) 2652-8700

HPE Aruba Networking 730 Series Campus Access Points

Thailand
Ukraine
Hereby, Hewlett Packard Enterprise declares that the radio equipment type [The Regulatory Model Number [RMN] for this device can be found in the Regulatory Model Name section of this document] is in compliance with Ukrainian Technical Regulation on Radio Equipment, approved by resolution of the CABINET OF MINISTERS OF UKRAINE dated May 24, 2017, No. 355. The full text of the UA declaration of conformity is available at the following internet address: https://certificates.ext.hpe.com/public/certificates.html. ' , 6280 -, -, 95002,
United States
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: n Reorient or relocate the receiving antenna. n Increase the separation between the equipment and receiver. n Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected. n Consult the dealer or an experienced radio or TV technician for help.
HPE Aruba Networking 730 Series Campus Access Points | 19

Improper termination of access points installed in the United States configured to a non-US model controller is a violation of the FCC grant of equipment authorization. Any such willful or intentional violation may result in a requirement by the FCC for immediate termination of operation and may be subject to forfeiture (47 CFR 1.80). The network administrator(s) is/are responsible for ensuring that this device operates in accordance with local/regional laws of the host domain.
n FCC regulations restrict the operation of this device to indoor use only. n Operation on oil platforms, cars, trains, boats, and aircraft shall be prohibited except for on large aircraft
flying above 10,000 feet. n Operation in the 5.925-7.125GHz band is prohibited for control or communication with unnamed aircraft
systems.
n RF Radiation Exposure Statement: This equipment complies with RF radiation exposure limits. This equipment should be installed and operated with a minimum distance of 7.87 inches (20 cm) between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
n Déclaration de la concernant l'exposition aux rayonnements à fréquence radioélectrique (FR): Cet appareil est conforme aux limites d'exposition aux rayonnements FR établies. Il doit être installé et utilisé à une distance minimale de 20 cm (7,87 pouces) entre le radiateur et votre corps. Cet émetteur ne doit pas être installé ou utilisé à proximité immédiate d'une autre antenne ni d'un autre transmetteur.
n Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
n Toute modification effectuée sur cet équipement sans l'autorisation expresse de la partie responsable de la conformité est susceptible d'annuler son droit d'utilisation.

HPE Aruba Networking 730 Series Campus Access Points

Proper Disposal of HPE Aruba Networking Equipment
HPE Aruba Networking equipment complies with countries' national laws for proper disposal and electronic waste management.
Waste of Electrical and Electronic Equipment
HPE Aruba Networking products at end of life are subject to separate collection and treatment in the EU Member States, Norway, and Switzerland and therefore are marked with the symbol shown at the left (crossed-out wheelie bin). The treatment applied at end of life of these products in these countries shall comply with the applicable national laws of countries implementing Directive 2012/19/EU on Waste of Electrical and Electronic Equipment (WEEE).
European Union RoHS
Hewlett Packard Enterprise products comply with the EU Restriction of Hazardous Substances Directive 2011/65/EU (RoHS). EU RoHS restricts the use of specific hazardous materials in the manufacture of electrical and electronic equipment. Specifically, restricted materials under the RoHS Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, Hexavalent Chromium, and Bromine. Some products are subject to the exemptions listed in RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging will be marked with the "RoHS" label shown at the left indicating conformance to this Directive.
India RoHS
This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) Rules, governed by the Ministry of Environment & Forests, Government of India.
HPE Aruba Networking 730 Series Campus Access Points | 21

China RoHS
HPE Aruba Networking products also comply with China environmental declaration requirements and are labeled with the "EFUP 50" label shown at the left.

HPE Aruba Networking 730 Series Campus Access Points

Taiwan RoHS
Turkey RoHS material content declaration
Türkiye Cumhuriyeti: AEEE Yönetmeliine Uygundur
HPE Aruba Networking 730 Series Campus Access Points | 23

References

madbuild