Blisse Brass Wall Sconce

Important Safety Instructions

The following safety precautions should always be followed to reduce the risk of electric shock, personal injury, or fire. It is important to read all of these instructions carefully before using the product and to save them for future reference or new users.

• This product must only be used as intended in accordance with the enclosed operating instructions.
• Do not carry the appliance by the mains cable or pull the cable to remove the plug from the socket.
• If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer or their service agent or a similar qualified person to avoid a hazard.
• If the appliance stops unexpectedly or appears to malfunction, switch off the power supply, unplug from the mains, and stop using immediately. Seek professional advice to rectify the fault or make repairs.
• Switch off the power supply or unplug from the mains socket when not in use, before cleaning, or changing accessories.
• Avoid positioning the appliance where the power cable might be accidentally trapped or damaged.
• Keep the appliance and cable away from sources of heat, sharp objects, or anything that may cause damage.
• Ensure the appliance is switched OFF before connecting the mains power supply.
• Be aware that some surfaces may become hot. Do not touch hot surfaces and supervise others accordingly.
• This product has not been designed for use by children.
• Children should be closely supervised at all times when they are near any electrical appliance.
• To protect against electric shock, never allow the appliance, the mains cable, or plug to come into contact with water or any other liquid.
• Never reach for any appliance that has fallen into water. Switch off the power supply at the mains immediately and unplug. Do not re-use until the product has been inspected and approved by a qualified electrician.
• Always ensure that hands are dry before operating or adjusting any switch on the product or touching the plug and mains supply connections.
• To disconnect, first ensure that all controls are in the OFF position, then remove the plug from the electricity supply.
• Where relevant, keep all ventilation slots, filters, etc., uncovered and clear of debris. Never drop or insert objects into the openings.
• Do not use outdoors. This appliance has been designed for domestic indoor use only.

Additional Safety Precautions for Lighting

• Carefully read all instructions for the assembly and use of this item before connecting to an electricity supply.
• Use only the recommended bulb rating, as detailed on the lamp holder and/or label.
• Never use a bulb that is rated more than the recommended capacity.
• Light bulbs become very hot in seconds. Do not attempt to touch the bulb while the lamp is lit and supervise others accordingly.
• Before cleaning or replacing a defective bulb, switch off the lamp and unplug from the mains socket. Allow the bulb to cool for at least 10 minutes before touching it and making the change.
• Ensure the new bulb is secure in the holder before reconnecting to the power supply.
• If in doubt, consult a qualified electrician.

Product Specification

Rated voltage: 220-240V ~ 50Hz

This lamp requires: 1x Max 10W G9 LED bulb (Not included). Do not use halogen bulb or else glass shade may be very hot.

Accessories

[Diagram: Shows an expansion bolt, a metal screw, and a location hole card.]

Instructions for Installation

[Diagram: Shows the Blisse Brass Wall Sconce product.]

Step 1: Prepare the Wall

Place the location holes card on the wall where you intend to hang the lamp. Use a pencil or marker pen (not included) to mark the positions for 3 holes.

[Diagram: Shows a wall with a location holes card being held against it, with a pencil marking holes.]

Step 2: Drill Holes

Drill holes at the marked positions using a pistol drill (not included). Ensure the drill diameter is 5-5.2mm and the holes are deeper than 30mm.

[Diagram: Shows a drill making holes in a wall.]

Step 3: Insert Expansion Bolts

Insert the expansion bolts into the drilled holes. Use a hammer (not included) to gently tap them flush with the wall surface.

[Diagram: Shows expansion bolts being inserted into wall holes, with a hammer nearby.]

Step 4: Install Metal Screws

Install the metal screws into the expansion bolts. Ensure there is a 3-5mm gap between the metal screw head and the expansion bolt for hanging the lamp.

[Diagram: Shows metal screws being screwed into expansion bolts, with a note about a 3-5mm gap.]

Step 5: Hang the Lamp

Carefully hang the assembled lamp fixture onto the installed metal screws on the wall.

[Diagram: Shows the wall sconce fixture being hung on the wall screws.]

Step 6: Install the Bulb

Insert a Max 10W G9 LED bulb (not included) into the lamp holder.

[Diagram: Shows a light bulb being inserted into a lamp holder.]

Step 7: Install the Glass Shade

Screw the glass shade onto the lamp holder. Pay attention to aligning the threads correctly for a secure fit.

[Diagram: Shows a glass shade being screwed onto the lamp holder.]

Step 8: Connect Power

Check that all components are securely assembled. Connect the lamp to the mains electrical supply.

[Diagram: Shows the assembled lamp connected to mains wiring.]

12 Month Warranty

Thank you for your purchase from Kmart.

Kmart Australia Ltd warrants this product to be free from defects in materials and workmanship for 12 months from the date of purchase, provided it is used according to the instructions. This warranty is in addition to your rights under the Australian Consumer Law.

Kmart will offer a refund, repair, or exchange if the product becomes defective within the warranty period. Kmart will cover reasonable expenses for warranty claims. The warranty does not cover defects caused by alteration, accident, misuse, abuse, or neglect.

Retain your receipt as proof of purchase. For assistance, contact Kmart Customer Service Centre on 1800 124 125 (Australia) or 0800 945 995 (New Zealand), or visit Kmart.com.au. Warranty claims and return expenses can be addressed to the Customer Service Centre at 690 Springvale Rd, Mulgrave Vic 3170.

This product comes with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for other foreseeable loss or damage. Goods will be repaired or replaced if they fail to be of acceptable quality and the failure is not major.

For New Zealand customers, this warranty is in addition to statutory rights under New Zealand legislation.