User Manual for Infinix models including: YYS-X6531, 2AIZN-YYS-X6531, 2AIZNYYSX6531, X6531 HOT 50i Smart Phone, HOT 50i Smart Phone, Smart Phone
INFINIX MOBILITY LIMITED YYS-X6531 2AIZN-YYS-X6531 2AIZNYYSX6531 yys x6531
File Info : application/pdf, 10 Pages, 268.41KB
DocumentDocumentInfinix HOT 50i X6531 User Manual (S&T&X&Y&Ac&Ad) Exploded diagram specification 1 TP 3 SIM CARD HOLDER 5 SIDE KEY 7 GROUNDED COPPER FOIL 9 POST-FLASH CONDUCTIVE FOAM 11 SUPPORT FOAM 13 TOP COOLING FIN 15 REAR FLASH FPC 2 MAIN PBC 4 FINGERPRINT FPC 6 WATERPROOF MYLAR 8 FRONT SHELL 10 FRONT-FACING CAMERA 12 POST-FLASH CONDUCTIVE FOAM 14 REAR CAMERA LENS 16 MIDDLE BEZEL 1 17 DECORATIVE LENS 18 SCREW 19 BATTERY COVER 20 TYPE-C RUBBER SLEEVE 21 UP TRUMPET 22 VICE BOARD 23 HEAT SINK IN THE MIDDLE FRAME 24 IC COPPER FOIL 25 REAR EARTHED COPPER FOIL 26 MOTOR 27 TRUMPET 28 CAMERA MOUNT 29 BATTERY 30 FINISHING COMPONENT 31 HEADSET RUBBER SLEEVE 32 SIDE KEY FPC 33 BOT COOLING FIN 34 COOLING FINTRUMPET 35 REAR SECONDARY CAMERA 36 FRONT CAMERA GROUND LENS COPPER FOIL Know your phone 2 1. Front camera 2. Volume + button 3. Volume - button 4. Power button & side fingerprint sensor SIM/SD card installation 3 1. Power off your phone. 2. Refer to the following picture for SIM/SD card installation. Charging the phone 2 You can charge your phone with a charger or by connecting it to a computer using a USB cable (comes with the phone). Use only Infinix chargers and cables. Other chargers or cables may damage the phone and invalidate its warranty. 3 FCC Caution 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Information to the user. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Specific Absorption Rate (SAR) information: This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: X6531 (FCC ID: 2AIZN-YYS-X6531) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.797 W/kg and when properly worn on the body is 4 0.576W/kg. Body-worn Operation This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna. 5 For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved. Operating System: AndroidTM Android is a trademark of Google LLC. 6