PERLESMITH Table Top TV Stand Instruction Manual

Introduction

Thank you for choosing Perlesmith. We strive to provide the best quality and services for our customers. For any parts inquiries, please contact AV Supply Group.

AV Supply Group Contact Information:

• New Zealand: Phone: +64 9 2749172, Email: info@avsupply.co.nz
• Australia: Phone: +61 3 90714585, Email: info@avsupplygroup.com.au

IMPORTANT SAFETY INFORMATION

• Please read through these instructions completely before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact customer service.
• Check package contents against the Supplied Parts and Hardware List to assure that all components were received undamaged. Do not use damaged or defective parts. If you require replacement parts, contact customer service.
• Not all parts and hardware included will be used.
• Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. Perlesmith disclaims any liability for injury or damage arising from incorrect assembly or incorrect use of this product.

Supplied Parts and Hardware

The following parts and hardware are supplied with the TV stand:

Supplied Parts:

• Left Base Plate (A1 x1)
• Left Junction Plate (A2 x1)
• Left TV Bracket (A3 x1)
• Left TV Bracket (A4 x1)
• Right Base Plate (B1 x1)
• Right Junction Plate (B2 x1)
• Right TV Bracket (B3 x1)
• Right TV Bracket (B4 x1)

Hardware:

• M6x10 Bolt (C x8)
• M6 Nut (D x4)
• Allen Key (E x1) [⚙️]
• Wrench (F x1) [?]

Hardware for Attaching TV Brackets to TV:

• M4x12 Bolt (G1 x4)
• M4x30 Bolt (G2 x4)
• M6x15 Bolt (H1 x4)
• M6x35 Bolt (H2 x4)
• M8x15 Bolt (I1 x4)
• M8x35 Bolt (I2 x4)
• M8x50 Bolt (I3 x4)
• M4/M5 Washer (J x4)
• M6/M8 Washer (K x4)
• L10mm Spacer (L x4)
• L2.5mm Spacer (M x8)
• L22mm Spacer (N x4)

Assembly Instructions

Step 1: Connect the Base Plates to Junction Plates

Attach the Left Base Plate (A1) to the Left Junction Plate (A2). Attach the Right Base Plate (B1) to the Right Junction Plate (B2). Use the appropriate bolts and nuts (likely C and D) and tighten with the Allen Key (E) and Wrench (F).

Step 2: Connect the TV Brackets

Connect the Left TV Brackets (A3, A4) to the assembled base and junction plate structure. Connect the Right TV Brackets (B3, B4) to the assembled base and junction plate structure. Use the provided bolts (likely D) and tighten with the Wrench (F).

Step 3: Secure the Bracket on the Holder According to Your Height Choice

There are two choices for height adjustment. Secure the TV bracket assembly onto the main stand holder structure. This involves attaching the bracket components (e.g., A3, A4, B3, B4) to the stand using fasteners (likely C) and potentially spacers (e.g., A2, B2).

Step 4: Secure the TV Brackets on TV

Bolt Length Verification: Ensure adequate thread engagement with the bolts or bolts/spacers combination. Using bolts that are too short will not hold the TV securely. Using bolts that are too long can damage the TV.

• Correct Bolt Selection: Look for a bolt that is the correct length, providing secure attachment without over-penetration.

Option A (For Flat Back TV)

Attach the Left TV Bracket (A4) and Right TV Bracket (B4) to a flat-backed television. Use the appropriate bolts (G1, H1, or I1) along with washers (J or K). Spacers (L, M, or N) may be needed depending on the TV's back panel. A Phillips screwdriver (not included) is required for tightening.

Option B (For Round Back TV)

Attach the Left TV Bracket (A3) and Right TV Bracket (B3) to a round-backed television. Use the appropriate bolts (G2, H2, I2, or I3) along with washers (J or K). Spacers (L, M, or N) may be needed depending on the TV's back panel. A Phillips screwdriver (not included) is required for tightening. Ensure the bracket is positioned correctly for the TV's VESA holes.

Alternate Spacer Setups

Various combinations of spacers (L, M, N) and washers (J, K) can be used with the bolts to achieve the correct fit for different TV models.