Pro Audio Video Manufacturer
User Guide for infobit models including: DAP6, iSpeaker DAP6, iSpeaker DAP6 Network PoE Speaker, Network PoE Speaker, PoE Speaker, Speaker
infobit iSpeaker DAP6
File Info : application/pdf, 3 Pages, 267.45KB
DocumentDocumentiSpeaker DAP6 Quick Guide 1. Overview The network PoE speaker provides power supply, audio transmission, and signal control using only a low-cost Cat5 twisted pair cable. It can get power supply from any 802.3ATstandard Ethernet switch and uses SSA inverter technology to achieve efficient amplification with superior sound quality even for low-power designs. High-quality audio and control signals can be delivered through the DanteTM network port and routed through the DanteTM Controller. DSP integrates gain control, silence control, 5-band equalizer control and amplitude limiting control functions, all of which can be controlled remotely from PC or Mac by control software. 2. Technical parameters Technical Sensitivity Output power Maximum sound pressure Power Impedance Vertical coverage Horizontal Bass 6.5-inch x1, treble 1-inch imported magnesium film + horn drive 92dB (1w@1m) 15.4-30W (Determined by PoE output) 118dB 60W 8 60° 90° coverage Frequency Response Range Interface Transmission protocol Power supply method DSP processing Installation Net weight Speaker size 70 Hz-21kHz RJ45 Dante PoE power supply support Bring your own hangers 4.1 Kg 197mm X 300mm X 118mm 3. Connect Connect the RJ45 port of the speaker to the Ethernet port of the PoE switch using twisted pair Cat5 cable. Before switching on the power supply, connect the device properly. About the input source: Connect the input source to the Ethernet port of the PoE switch using a twisted pair Cat5 cable. The input should be DanteTM. Note: PoE switches are compatible with the 802.3at standard. 4. Software control 4.1 Dante Controller After the speaker is connected to the switch, open the Dante Controller software, where the routing and device setup of Dante audio will be completed. When users connect to Dante devices, INFOBIT AV www.infobitav.com info@infobitav.com there is no need to set up the software, and the software can search for all Dante devices in the first time. The diagram below: device for pairing. You only need to find and click the crossing point of the input terminal and output terminal, and the green icon as shown below indicates that the channel is successfully paired. All Dante devices appear on the software, so the next step is to start matching device channels one by one. When we click on the plus sign next to the device name, the Dante channel for the device is displayed. The input Users can customize the name of Dante device according to their own needs for easy memory. At the same time, open the input terminal and output terminal of the The output end Dante also has a very nice feature, which is the ability to remember previously matched pathways, and when all of your Dante devices are disconnected, when reconnect, you don't have to re-pair them, all of the route connections remain as they were before they were disconnected. 4.2 Please visit the download page of our official website to download. Open the software and select the speaker you want to control from the drop-down menu at the top left. If there is no speaker to control in the menu, click the "Scan" button to scan the connected devices. After opening the software, click to select the device ID of the mobile speaker to connect the mobile speaker. Note: After scanning, the computer will detect all connected DanteTM devices, INFOBIT AV www.infobitav.com info@infobitav.com please select a matching type of device for control. 4.2.1 Scene Setting Area Save Settings Load Settings Default Settings 4.2.2 Fader control area Attention To ensure the reliable use of the equipment and the safety of personnel, observe the following precautions when installing, using, and maintaining the equipment: 1. Avoid the danger of electric shock, do not open the case. There is no part in the machine that can be repaired by the user. Nonprofessionals are not allowed to disassemble the equipment without permission, so as to avoid increasing the damage of the equipment. When repairs are needed, please contact the designated professional maintenance personnel. 2. The machine shall not be exposed to dripping or splashing water. Do not place liquid objects such as vases on the device. 3. Do not spill any corrosive chemicals or liquids on or near the equipment. 4.3.3 Frequency division area INFOBIT AV www.infobitav.com info@infobitav.com