Inicio – Cominsa
INTECS Teknikatama Industri | INTECS Teknikatama Industri
Battery Storage Specialists Since 1963 | Probe Group
Homepage | Wabtec Corporation
Instruction Manual for Wabtec models including: ASMB0911, YIY-ASMB0911, YIYASMB0911, ASMB0911 Mini Dual RF UHF Module Silabs, ASMB0911, Mini Dual RF UHF Module Silabs, RF UHF Module Silabs, Module Silabs
Industrea Mining Technology Pty Ltd ASMB0911 Mini Dual RF UHF Module SiLabs YIY-ASMB0911 YIYASMB0911 asmb0911
File Info : application/pdf, 14 Pages, 855.19KB
DocumentDocument1 - General Business Digital Mining Technology ASMB0911 MINI DUAL RF UHF MODULE SILABS HARDWARE INTEGRATION MANUAL © 2020 Wabtec Corporation. All rights reserved. The information contained in this publication is the property of Wabtec Corporation. This publication shall not be reproduced, redistributed, retransmitted, translated, abridged, adapted, condensed, revised or otherwise modified, in any form, in whole or in part, without the express written consent of Wabtec. By accessing this, you agree that the information contained herein does not purport to cover all details or variations in Wabtec products or to provide for every possible contingency with installation, operation or maintenance. Should further information b matter should be referred to Wabtec Corporation. Any applicable Federal, State or local regulations or company safety or operating rules must take precedence over any information or instructions given in the Technical Documentation. Wabtec has no obligation to keep the material up to date after the original publication. WABTEC CORPORATION EXPLICITLY DISCLAIMS ALL WARRANTIES OF ACCURACY, MERCHANTABILITY OR FITNESS FOR ANY PURPOSE IN CONNECTION WITH THIS PUBLICATION AND USE THEREOF.. CONTENTS 1 - General Business 1. MANUFACTURER INFORMATION................................................................................................. 3 1.1. INTRODUCTION..............................................................................................................................3 1.2. SAFETY INFORMATION ..................................................................................................................3 1.3. DISCLAIMER ...................................................................................................................................3 1.4. COMPANY DETAILS ........................................................................................................................4 2. OVERVIEW .................................................................................................................................. 5 2.1. GENERAL FEATURES.......................................................................................................................5 2.2. ABBREVIATIONS .............................................................................................................................5 2.3. SCOPE & SPECIFICATION................................................................................................................5 2.4. PIN CONFIGURATION AND FUNCTION ..........................................................................................6 2.5. APPROVED ACCESSORIES LIST .......................................................................................................7 2.6. WARNINGS.....................................................................................................................................7 3. GENERAL INFORMATION ............................................................................................................. 8 3.1. INTEGRATION.................................................................................................................................8 3.2. MAINTENANCE...............................................................................................................................8 3.3. DECOMMISSION AND DISPOSAL ...................................................................................................8 3.4. AUTHORIZED REPRESENTATIVES ...................................................................................................9 4. PRODUCT APPROVALS AND REGULATORY INFORMATION ......................................................... 10 4.1. DECLARATION OF CONFORMITY 47 CFR § 2.1077 COMPLIANCE INFORMATION.......................10 4.2. MODULE STATEMENT, LABELLING & USER INSTRUCTIONS ........................................................10 4.3. FCC INTERFERENCE STATEMENT FOR CLASS B DEVICES .............................................................11 4.4. FCC RADIATION EXPOSURE STATEMENT.....................................................................................12 4.5. INDUSTRY CANADA COMPLIANT .................................................................................................12 CONCERNING RADIO TRANSMITTERS .................................................................................12 INDUSTRY CANADA - RADIATION EXPOSURE STATEMENT .................................................12 INDUSTRIE CANADA ......................13 ..............................................................13 AU SUJET DES ÉMETTEURS RADIO.......................................................................................13 4.6. AUSTRALIAN RADIO COMMUNICATIONS EQUIPMENT RADIATION EXPOSURE STATEMENT..13 ASMB0911 Hardware Integration Manual Rev: C Page 2 of 14 1 - General Business 1. 1.1. MANUFACTURER INFORMATION INTRODUCTION The product or product family described under scope of this document will be henceforth referred to as DEVICE. This manual provides the information on the DEVICE, its variants, specifications, operation, maintenance, decommission and disposal. 1.2. SAFETY INFORMATION The safety section includes safety precautions which must be observed when working on items that appear throughout the manual. Examples of safety precautions and labels are outlined below: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Indicates a potential for equipment damage. 1.3. DISCLAIMER implied warranty of any kind. Wabtec makes no ANY EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER EXPRESS OR IMPLIED WARRANTY REGARDING ANY PRODUCTS DESCRIBED in these materials. To the maximum extent permitted by law, Wabtec disclaims any and all implied warranties that might otherwise arise or apply, including any implied warranty of merchantability or of fitness for a particular purpose. Wabtec further makes no representation or warranty of accuracy of these materials and neither Wabtec will have no responsibility or liability for any error or omission in these materials. These specifications are subject to change without notice. ASMB0911 Hardware Integration Manual Rev: C Page 3 of 14 1 - General Business 1.4. COMPANY DETAILS Manufacturer: 1 - General Business Industrea Mining Technology Pty Ltd (trading as Digital Mining Technology) 3 Co-Wyn Close Fountaindale, New South Wales, 2258 Australia Telephone +61 2 8863 4730 dm.fulfilment@wabtec.com www.wabteccorp.com Industrea Mining Technology Pty Ltd is a registered business subsidiary of Wabtec Corporation ASMB0911 Hardware Integration Manual Rev: C Page 4 of 14 1 - General Business 2. OVERVIEW 2.1. GENERAL FEATURES The ASMB0911 is a digitally controlled radio module implemented on an industry standard M2.xx style circuit board. This module can use used in a host controller board to provide a short range, power limited UHF radio link for a variety of applications. Key features include: Silabs Si4463 digitally controlled radio Qty: 2 Nos. Power supply regulation/conditioning Serial interface Dual RF antennae connectors 2.2. ABBREVIATIONS ABBREVIATION V2V N/C DESCRIPTION Vehicle to Vehicle Not Connected 2.3. SCOPE & SPECIFICATION This user manual covers Mini Dual RF UHF Module Silabs Radio Module, Model No.: ASMB0911. FEATURE Operating Frequency Band Nominal Transmit Power Chipset Chipset Frequency Range Modulation Antenna Type Antenna Gain Additional Mitigation Techniques Rated Voltage Operating Temperature Module Dimensions DETAIL 869.40 - 869.650 MHz 902 928 MHz 20 dBm at MMCX Pins SiLabs Si4463 2 Nos. 142 1050 MHz 4GFSK Two MMCX antenna connectors 902-928 MHz: Peak Gain +8 dBi max 869.40 - 869.650 MHz: Peak Gain +2.9 dBi max Listen Before Talk 3.3 Vdc -40°C to +85°C 45 mm x 32 mm ASMB0911 Hardware Integration Manual Rev: C Page 5 of 14 1 - General Business 2.4. PIN CONFIGURATION AND FUNCTION PIN SIGNAL 74 Vsupply (+3.3V) 72 Vsupply (+3.3V) 70 VIO 68 VSTDBY 66 PWREN/#SDN 64 RESERVED-DBG 62 I2C-BUSEN 60 I2C-SCA 58 I2C-SDA 56 ID-CATEGORY 54 ID-VARIANT 52 #RESET 50 CLK32K 48 RESERVED 46 RESERVED 44 RF_COEX 42 SYNC OUT 40 SYNC IN 38 UART-DTR 36 UART-RTS 34 UART-CTS 32 UART-TXD 30 MECH E KEY 28 MECH E KEY 26 MECH E KEY 24 MECH E KEY 22 UART-RXD 20 UART-DSR 18 GND 16 WAKE/#LPMODE 14 SPI-MOSI 12 SPI-MISO 10 SPI#SS 8 SPI-SCK 6 #IRQ 4 RESERVED 2 RESERVED TYPE PWR PWR PWR PWR CMOS N/C CMOS CMOS-OD CMOS-OD Passive Passive CMOS-OD CMOS N/C N/C CMOS-OD CMOS CMOS CMOS CMOS CMOS CMOS CMOS CMOS PWR CMOS CMOS CMOS(HiZ) CMOS CMOS CMOS-OD N/C N/C PIN SIGNAL 75 GND 73 RESERVED 71 RESERVED 69 GND 67 RESERVED 65 RESERVED 63 GND 61 RESERVED 59 RESERVED 57 GND 55 RESERVED 53 RESERVED 51 GND 49 RESERVED 47 RESERVED 45 GND 43 RESERVED 41 RESERVED 39 GND 37 RESERVED 35 RESERVED 33 GND 31 MECH E KEY 29 MECH E KEY 27 MECH E KEY 25 MECH E KEY 23 RESERVED 21 RESERVED 19 RESERVED 17 RESERVED 15 RESERVED 13 RESERVED 11 RESERVED 9 RESERVED 7 GND 5 RESERVED 3 RESERVED 1 GND TYPE PWR N/C N/C PWR N/C N/C PWR N/C N/C PWR N/C N/C PWR N/C N/C PWR N/C N/C PWR N/C N/C PWR N/C N/C N/C N/C N/C N/C N/C N/C PWR N/C N/C PWR ASMB0911 Hardware Integration Manual Rev: C Page 6 of 14 1 - General Business 2.5. APPROVED ACCESSORIES LIST The below table outlines the accessories that are approved for operation with this Module: For V2V Radio operation, this module has been tested and approved for use with the antenna listed below. The module may be integrated with other antennas of the same type and antenna gains of less than or equal than the approved. For 902-928 MHz frequency band: ANTENNA PART NO. FREQUENCY PROD1196 865-930MHz MISC1626 915 MHz MISC0607 865-930MHz EA2-0287-N01SP-050 860-930 MHz ANTENNA TYPE Omni-directional Monopole Type Omni-directional Omni-directional PEAK GAIN +2.9 dBi Max +2 dBi Max -2.4 dBi Max +8 dBi Max For 869.400-869.650 MHz frequency band: ANTENNA PART NO. FREQUENCY ANTENNA TYPE PROD1196 865-930MHz Omni-directional MISC1625 824-2170 MHz Monopole Type MISC0607 865-930MHz Omni-directional PEAK GAIN +2.9 dBi Max +1.9 dBi Max -2.4 dBi Max 2.6. WARNINGS Keep this Integration Manual for later reference. Do not leave this Module in an uncontrolled environment where the storage temperature is below-40°C (-40°F) or above 85°C (176°F). This may damage the DEVICE. Do not operate this Module outside specified temperature range. Refer to specification table for further information. ASMB0911 Hardware Integration Manual Rev: C Page 7 of 14 1 - General Business 3. GENERAL INFORMATION 3.1. INTEGRATION Module Integration should be in accordance with the procedures defined by Digital Mining Technology and only performed by the manufacturer or authorized representative. Host equipment must be configured to the modulation schemes to comply with the modular approval listed in Sec. 2.3 and adhere to all local regulations appropriate for automotive Installations in the end-user geographic region. 3.2. MAINTENANCE This equipment is not intended to be maintained by the end user. Opening the enclosure should not be attempted, will void any warranty and could compromise the safe operation of the unit. No user-serviceable parts. Contact your local authorized representative for service arrangements. 3.3. DECOMMISSION AND DISPOSAL Power should be disconnected before decommissioning. Disposal of electronics should be done in accordance with local regulations. The unit must not be treated as general waste. By ensuring that this product is disposed of correctly, you will be helping to prevent potentially negative consequences for the environment and human health which could otherwise be caused by incorrect handling of this product. Waste Disposal Method: Recycling is encouraged. Dispose of in accordance with local, state and federal laws and regulations. USA: Dispose of in accordance with local, state and federal laws and regulations. Canada: Dispose of in accordance with local, state and federal laws and regulations. EC: Dispose of in accordance with relevant EC Directives. ASMB0911 Hardware Integration Manual Rev: C Page 8 of 14 1 - General Business 3.4. AUTHORIZED REPRESENTATIVES Australia Brazil Canada Industrea Mining Technology Pty Ltd, Trading as Digital Mining Technology 3 Co-Wyn Close Fountaindale, NSW, 2258 Australia Wabtec Brasil Fabricação e Manutenção de Equipamentos Ltda Avenida General David Sarnoff n 4600 Cidade Industrial Contagem, MG 32210-110 Brazil Wabtec Transportation Canada Inc 84 Terracon Pl. Winnipeg Manitoba, R2J 4G7 Canada Telephone Telephone Fax Telephone +61 (2) 8863 4730 GETProductionIMT@wabtec.com www.wabteccorp.com +55 (31) 2103 5348 +55 (31) 2103 5100 www.wabteccorp.com +1 204-951-4320 www.wabteccorp.com India Indonesia Mexico North America Sub Saharan Africa Wabtec India Industrial Private Ltd ITC Green Centre 6th Floor, Southwest Tower No.18, Banaswadi Main Road, Maruthisevanagar Bangalore, Karnataka, 560005, India PT Intecs Teknikatama Industri Jl. Ciputat Raya No. 18D Kebayoran Lama Selatan, Jakarta, 12240 Indonesia Telephone Telephone Fax +91 (080) 6838 7816 www.wabteccorp.com +62 (21) 729 3351 +62 (21) 729 3352 www.intecs.co.id Comercializadora Minera Norte, S.A. DE C.V. Ave. H. Colegio Militar No. 2000-B Col. Las Fuentes Piedras Negras, Coahuila México. C.P. 26010 Digital Mining 2901 East Lake Road Erie, Pennsylvania, 16531 USA Telephone Fax Telephone Fax +52 (878) 783 8215 +1 (830) 352 5519 +52 (878) 783-8218 www.cominsa.com.mx +1 (480) 264 2063 +1 (480) 264 6402 www.wabteccorp.com Probe Integrated Mining Technologies (PTY) Ltd 245 Albert Amon Road Meadowdale, Germiston, 1614 South Africa Telephone Fax +27 (11) 453 0924 +27 (11) 453 2141 www.probebattery.co.za ASMB0911 Hardware Integration Manual Rev: C Page 9 of 14 1 - General Business 4. PRODUCT APPROVALS AND REGULATORY INFORMATION ASMB0911 module have modular approval and comply with FCC Part 15 and Canada Innovation, Science and Economic Development Canada (ISED) RSS-247 and RSS-Gen. FCC ID: IC: YIY-ASMB0911 8903A-ASMB0911 Modifications to this product without written consent from the manufacturer or its designated authorized representatives 4.1. DECLARATION OF CONFORMITY 47 CFR § 2.1077 COMPLIANCE INFORMATION We, Industrea Mining Technology Pty Ltd, T/A Digital Mining Technology, at 3 Co-Wyn Close, Fountaindale, NSW, 2258, Australia declare under our sole responsibility the products: Trade Name: Model Number: Product Name FCC ID: Responsible Party: Digital Mining Technology ASMB0911 Mini Dual RF UHF Module Silabs YIY-ASMB0911 Digital Mining 2901 East Lake Road Erie, PA, 16531 (814) 875-2234 Complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. 4.2. MODULE STATEMENT, LABELLING & USER INSTRUCTIONS The ASMB0911 has single module approval and comply with FCC Part 15 and Canada Innovation, Science and Economic Development Canada(ISED) RSS-247 and RSS-Gen. Single-modular transmitter approval is defined as a complete RF transmission subassembly, designed to be incorporated into another device, that must demonstrate compliance with FCC/IC rules and policies independent of any host. A transmitter with a modular grant can be installed in different end-use products (referred to as a host, host product, or host device) by the grantee or other equipment manufacturer, then the host product may not require additional testing or equipment authorization for the transmitter function provided by that module. The user must comply with all of the instructions provided by the Grantee, which indicate installation and/or operating conditions necessary for compliance. The host product itself is required to comply with all other applicable FCC/IC equipment authorizations regulations, requirements and equipment functions that are not associated with the transmitter module portion. For example, compliance must be ASMB0911 Hardware Integration Manual Rev: C Page 10 of 14 1 - General Business demonstrated: to regulations for other transmitter components within a host product; to requirements for unintentional radiators(Part 15 Subpart B, ICES-003), such as digital devices, computer peripherals, radio receivers, etc.; and to additional authorization requirements for the non-transmitter functions on the transmitter module (i.e., Suppliers Declaration of Conformity (SDoC) or certification) as appropriate. LABELING AND USER INFORMATION REQUIREMENTS: The ASMB0911 module has been labeled with its own FCC/IC ID number, and if the FCC/IC ID number is not visible when the module is installed inside another device, then the outside of the finished product into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wordings as follows: Contains Transmitter Module FCC ID: YIY-ASMB0911 or Contains FCC ID: YIYASMB0911 Contains Transmitter Module IC: 8903A-ASMB0911 or Contains IC: 8903A-ASMB0911 4.3. FCC INTERFERENCE STATEMENT FOR CLASS B DEVICES This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. A shielded type Ethernet cord is required to meet FCC Class B emission limits and prevent interference to the nearby radio and television reception. This device and its antenna(s) must not be co-located or operate in conjunction with any other antenna or transmitter. The antenna is considered an integral system component. Use of any antenna other than those specified in the installation manual or supplied with the ASMB0911 Hardware Integration Manual Rev: C Page 11 of 14 1 - General Business 4.4. FCC RADIATION EXPOSURE STATEMENT To comply with FCC RF exposure limits for general population / uncontrolled exposure, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure limits for general population / uncontrolled exposure, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. 4.5. INDUSTRY CANADA COMPLIANT This Class B digital apparatus complies with Canadian ICES-003. Changes or modifications not expressly approved by the party responsible for compliance CONCERNING RADIO TRANSMITTERS This device subject to the following two conditions: -exempt RSSs. Operation is 1. This device may not cause interference; and 2. This device must accept any interference, including that may cause undesired operation of the device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. INDUSTRY CANADA - RADIATION EXPOSURE STATEMENT To comply with Industry Canada RF exposure limits for general population / uncontrolled exposure, the antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. ASMB0911 Hardware Integration Manual Rev: C Page 12 of 14 INDUSTRIE CANADA 1 - General Business non contrôlée de la FCC/ IC RF, les antennes utilisées pour cet émetteur doivent être installées de manière à offrir une distance de séparation minimum de 20 cm pour les variantes de produits GSM ou de 20 cm pour les variantes de produits non GSM de toutes les personnes et ne antennes ou émetteurs. Cet appareil numérique de classe B est conforme à la norme canadienne ICES003. Les changements ou les modifications non approuvés expressément par la AU SUJET DES ÉMETTEURS RADIO Cet appareil respecte les systèmes Canada. Son fonctionnement est soumis aux deux conditions suivantes: 1. 2. Cet appareil doit accepter toute interférence, y compris celle qui réduire la possible interférence radio avec les autres utilisateurs, le type isotrope rayonnée équivalente (p.i.r.e.) ne soit pas plus grande que nécessaire pour une communication réussie. 4.6. AUSTRALIAN RADIO COMMUNICATIONS EQUIPMENT RADIATION EXPOSURE STATEMENT The equipment complies with the Radiocommunications Equipment(general) Rules 2021 + Amendment Rules 2023 (No. 1), Electromagnetic Radiation Human Exposure Standard RPS-1 for General Public Exposure, Non-Aware User, for a Compliance Level 2 Radiocommunications Equipment, when the minimum safety distance is adhered to, and shall bear the RCM. ASMB0911 Hardware Integration Manual Rev: C Page 13 of 14 1 - General Business DOCUMENT NO ASMB0911-HARWARE INTEGRATION MANUAL-A ASMB0911-HARWARE INTEGRATION MANUAL-B ASMB0911-HARWARE INTEGRATION MANUAL-C REVISION Original document Included Module statement, labelling & User Instruction in Sec. 4.2 Included MISC0607 Antenna & extended operating temp to +85°C DOCUMENT REVISION NO. POSITION Certification Engineer DATE By P C Shivalingam at 7:22 pm, Nov 28, 2024 POSITION DATE Design Engineering By Stephen Coates at 11:40 am, Nov 29, 2024 POSITION DATE Engineering Manager By Peter O'Donnell at 1:11 pm, Nov 29, 2024 ASMB0911 Hardware Integration Manual Rev: C Page 14 of 14