Instruction Manual for dyson models including: TP-09Pro, TP09-1Pro, TP-09 Pro Cool and Heat with Hepa and Plasma, TP-09 Pro, Cool and Heat with Hepa and Plasma
Dyson Torenventilator AM07 Wit/Zilver | bol.com
File Info : application/pdf, 1 Pages, 1.49MB
DocumentDocumentCool & Heat with Hepa & Plasma Operating Instruction Thank you very much for using our products, please kindly read through the manual before usage. TP09-1PRO Introduction of Product fittings Air quality monitoring lamp 1. Output channels 2. Outlet circle 3. Main body 4. Input channels 5. View screen Remote control & Touch screen button comparison Mode: TP-09PRO Product size:265*160*853(mm) Voltage220V~ Rating frequency: 50Hz Power rating: 35W (Cool Timming Speed contorl+/- Plasma 1950WHot Rotation angle: 120° ON/OFF Speed contorl+/Sway/Cancel Cool/Hot Switchover Positive and negative oxygen ions are blown out by the wind from the air outlet Air quality monitoring lamp 1.When the red light is on, the air quality is poor. 2.When the yellow light is on, the air quality is average. 3.When the blue light is on, the air quality is good. 4.When the green light is on, the air quality is excellent. DBD positive and negative oxygen ion generator Positive and negative oxygen ion mode: the warm wind mode automatically shuts down the positive and negative oxygen ion. loading and unloading Remove: pull out the front hands outwards.Installation: align the filter screen with the groove and press it inside. Cool Mode Hot Mode Plasma mode Clean 1. Press directly into cool mode 2.Press + or - into ajdust wind power Principle of air outlet 1. Press button then press button, hot/cool mode. 2.And press to change back to thenatural wind mode. 3.Warm air mode can be divided into three grades: high,middle,low, 3 grade high, 2 grade middle, 1 grade and lwo grade. 4.When the temperature reaches 35 degrees, it will automatically stand by and automatically turn on the warm air mode. Principle of Hot wind 1. heating mode automatically turns off plasma. Matters needing attention UTurn off the power, unplug the plug, and then wipe it with a clean and wet cloth. Do not use detergent or polishing agent to visually observe whether there is dust at the air outlet / air inlet, and then use a soft brush to remove the dust Replace Battery PTC heating unit TP series fans are different from traditional fans, which produce natural air by cutting air, but inhale air through the bottom air inlet, and then generate strong kinetic energy through the high-speed operation of the motor and turbocharging to form a stable and strong high-speed airflow. After choosing the Hot mode, the PTC ceramic heater built in the air duct will begin to heat up. When the air flow passes through the PTC heater, the air flow will get heating effect, thus releasing pleasant warm air. This heater is hot when in use and for a short period after use.Do not let bare skin touch hot surfaces. If children are present, consider positioning the heater out of their reach. Tear down the battery hatchcover, take out of used battery , then put the new battery instead of ,make battery bin is loaded in the positive & negative direction and close battery cover . IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN THIS MANUAL AND ON THE APPLIANCE. When using an electrical appliance, basic precautions should always be followed includjng the following: WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY: IMPORTANT SAFETY FEATURES For your safety this heater is fitted with automatic cut-out switches that operate if the heater tips over or overheats. If the switches operate, unplug the heater and allow it to cool. Before restarting the heater check and clear any blockages and ensure the heater is on a solid level surface READ AND SAVE THESE INSTRUCTIONS THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE ONLY Do not pull on the cadle. Do not store near heat sources. Do not use near open sources. Do not use carry by the air loop amplifier. the air loop amplifies is not a handle. In order to avoid overheating and fire hazard, do not cover the heater. Liang Shifu's Cool and Warm Fan is exempt from insurance for two years Terms and Conditions of One Year Warranty for Your Cooler's Cooling and Heating Fans · The warranty clause shall come into force as of the date of purchase. · All warranty work will be performed by Liang Shifu or his authorized agent. · Any replacement parts will be owned by Liang Shifu. · Under the warranty terms, repair and replacement services cannot extend the warranty period. · Please keep your purchase notes. · Before repairing your fans, you must provide purchase notes. Without this bill, any work we do will be charged. Scope covered · Within one year of purchase, defects due to poor materials, processes or functions will result in the repair and maintenance required (if there is no one component, or production has stopped, Liangshi will replace it with a practical component). Warranty card Full name: Customer Address: Telephone: Purchase Date: Warranty Period Two Years 1The product will be free of charge within two years from the date of purchase. 2If it is necessary to replace spare parts beyond the time limit specified in the preceding paragraph, the maintenance fee shall be charged as appropriate. 3During the warranty period, free repairs are not allowed in the following circumstances aFailure to query purchase records or provide purchase information bMaintenance beyond warranty period. cDamage caused by disassembly or renovation. dDamage caused by misuse/negligence orimproper use. eFaults or damages caused by non-ordinary household use (e.g. long-term use in places with poor environment). fThose whose appearance is naturally stained by use. Examination clerk Problem Description