DSD | Home
We engineer a better future | Danfoss
One moment, please...
Installation Guide for Danfoss models including: 70160-903, 0160-903 Closed Circuit Axial Piston Pump, 0160-903, Closed Circuit Axial Piston Pump, Axial Piston Pump, Piston Pump, Pump
70160 Closed Circuit Axial Piston Pump | Danfoss
File Info : application/pdf, 2 Pages, 179.20KB
DocumentDocumentInstallation Information No. 04-622 July 1999 Medium Duty Series Danfoss® Pumps Kit 70160-903 -02 Design Shimming Process Copyright Danfoss Corporation, 1999 All Rights Reserved Printed in USA Introduction This shim kit is to replace the crush ring within the trunnion cover. If the camplate, trunnion cover or housing is replaced during servicing, the old crush ring can no longer be used to assure proper preload. Shimming procedures: 1 Measure the thickness of the existing crush ring. 2 To obtain a starting point stack shims to the measurement of existing crush ring. Then insert shims into the trunnion cover in the same location as the removed crush ring. 3 Assemble the housing sub-assembly consisting of the housing, camplate, bearings and trunnion covers. Install the trunnion cover bolts and torque to 56,9 N·m [42 lbf·ft]. 4 With a torque wrench, check the torque required to rotate the control shaft. The specified torque level is 2,26 ± 0,6 N·m [±205 lbf·in]. - If torque level is too low, add additional shims and repeat steps 3 and 4 until specified torque levels are achieved. - If torque level is too high, remove shims and repeat steps 2 and 3 until specified torque levels are achieved. 5 Finish the assembly of the pump. Housing and Camplate O-ring Bearing Cup Old Crush Ring Replacement Shims Cover Plate Washers Cap Screws AN432572278580en-000101 · Cartridge valves · DCV directional control valves · Electric converters · Electric machines · Electric motors · Gear motors · Gear pumps · Hydraulic integrated circuits (HICs) · Hydrostatic motors · Hydrostatic pumps · Orbital motors · PLUS+1® controllers · PLUS+1® displays · PLUS+1® joysticks and pedals · PLUS+1® operator interfaces · PLUS+1® sensors · PLUS+1® software · PLUS+1® software services, support and training · Position controls and sensors · PVG proportional valves · Steering components and systems · Telematics Danfoss Power Solutions is a global manufacturer and supplier of high-quality hydraulic and electric components. We specialize in providing state-of-the-art technology and solutions marine sector. Building on our extensive applications expertise, we work closely with you to ensure exceptional performance for a broad range of applications. We help you and other customers around the world speed up system development, reduce costs and bring vehicles and vessels to market faster. Danfoss Power Solutions your strongest partner in mobile hydraulics and mobile Go to www.danfoss.com for further product information. outstanding performance. And with an extensive network of Global Service Partners, we also provide you with comprehensive global service for all of our components. Local address: Hydro-Gear www.hydro-gear.com Daikin-Sauer-Danfoss www.daikin-sauer-danfoss.com Danfoss Power Solutions (US) Company 2800 East 13th Street Ames, IA 50010, USA Phone: +1 515 239 6000 Danfoss Power Solutions GmbH & Co. OHG Krokamp 35 D-24539 Neumünster, Germany Phone: +49 4321 871 0 Danfoss Power Solutions ApS Nordborgvej 81 DK-6430 Nordborg, Denmark Phone: +45 7488 2222 Danfoss Power Solutions Trading (Shanghai) Co., Ltd. Building #22, No. 1000 Jin Hai Rd Jin Qiao, Pudong New District Shanghai, China 201206 Phone: +86 21 2080 6201 Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved. © Danfoss | January 2023