Airwheel SE3S User Manual

Products and Accessories

Thank you for purchasing the Airwheel SE3S Smart Rideable luggage. Please read the product instructions carefully before using the Airwheel SE3S and follow all instructions, notes, and warnings in this manual. Failure to do so will result in damage to the product and will not be covered by the warranty. Please keep the manual and warranty card in a safe place.

Illustration showing the Airwheel SE3S, its charger, a power bank, and the instruction manual.

SE3S Diagram

A detailed line drawing of the Airwheel SE3S with various components labeled. These include: Brake handle, Handle, Acceleration control, Handle telescopic lock, optional LED light, optional front trim baffle plate, Pedal, Motor wheel, TSA coded lock, Lift grip, Pull rod, Power bank compartment, Power button, Telescopic switch, and Rear wheel. A magnified inset shows the mechanism of the TSA coded lock.

Specifications

⚠️ In case of long-term non-use, the product needs to be fully charged and stored. It requires charging again after 2 months of inactivity.

⚠️ Please do not dispose of used batteries to avoid environmental pollution. The used lithium battery of this product is the responsibility of the company, distributors, and government-designated sites for recycling.

Use SE3S

Unfold

1. Turn on the power switch and place the telescopic switch in the "I" position (see Figure 1-1). The handlebars will automatically unfold. After expansion is complete, the telescopic switch will reset to the "o" position.
2. Loosen the handle telescopic lock. After pulling the handlebar to a proper position, fasten the handle telescopic lock. Check that there is no loosening and the unfolding is complete.

Fold

Turn on the power switch and place the telescopic switch in the "II" position (see Figure 1-1). The handlebars will automatically fold, and the telescopic switch will reset to the "o" position after folding is finished. Turn off the power.

Loosen the handle telescopic lock, shrink the handlebar until it cannot shrink, and fasten the handle telescopic lock.

• When retracting the handle, please straighten the handle first so that the handle is fully retracted.
• Before use, please check whether the handlebar connection is stable. If unstable, loosen the handlebar retraction latch, tighten the hand nuts, and then tighten the handlebar retraction latch.

Other Uses

1. Turn off the power, pull out the lever, you can drag (see Figure 1-3).
2. Pick up the "hands-on" and carry them (see Figure 1-4).

Figure 1-1 shows the power button, telescopic switch, and brake lever. Figure 1-2 shows a close-up of the brake lever and acceleration switch. Figure 1-3 illustrates dragging the SE3S using the pull rod. Figure 1-4 shows carrying the SE3S using the hand carry nut.

Riding SE3S

Riding Modes

• Forward: Turn on the power, unfold the SE3S, sit on the luggage body, place your feet on the pedals, and turn the acceleration handle to move forward.
• Brakes: Turn the brake lever to brake.
• Reverse (optional): Turn the brake switch and turn it off, then turn the acceleration switch to reverse.

Illustrations show the rider in Forward, Brakes, and Reverse positions.

Riding Precautions

1. Check if the power is sufficient and the brakes are in good condition before riding.
2. Before first use, it is recommended to charge to full power.
3. It is not recommended to brake or turn sharply during the ride to prevent side slip or rollover.
4. Please observe traffic rules and various site management regulations during use.
5. Avoid using this product in bad weather such as rain, snow, or ice.
6. When not in riding mode, turn off the power.

Power Bank Use

Power Bank Installation

Pull up the pull rod and insert the power bank along the card slot.

Power Bank Disassembly

Turn off the power, pull up the pull rod, and pull the power bank out of the card slot.

Note: When installing the power bank, please install it in the direction shown in Figure 1-5, with the front facing outward.

Figure 1-5 shows the power bank being inserted into the SE3S, labeled with Pull rod, Power bank, and card slot.

Power Bank Use

Illustration of the power bank showing its input/output interfaces: DC charging port and USB output interface. It also shows a Power View Switch and a power indicator with 5 grids, indicating battery level (full, decrementing, or insufficient charge).

Charging Power Bank

To charge the power bank, take out the power bank and the matching charger. Connect the matching charger to the AC100-240V power supply (mains), and then plug the matching charger into the power bank input interface (DC charging port). The charger indicator light will be red. After the Power Bank is fully charged, the charger indicator light will turn green.

Power Bank Use Precautions

1. If the factory time is short, the user can use the product directly. If the factory time is longer (more than 2 months), the power may be lost during storage and transportation. The battery should be recharged before use.
2. Do not charge with other brands of chargers.
3. The Power Bank contains high-voltage circuits inside and is packaged intact by the factory. Do not disassemble or tamper with it.
4. Use and store to prevent liquid and metal particles from penetrating into the interior of the Power Bank.
5. The Power Bank cannot be close to open flame or high temperature heat sources, nor can it be thrown into water. In hot weather, charging the power bank in direct sunlight is strictly forbidden.
6. It is strictly forbidden to short-circuit the positive and negative poles of the Power bank with wires or conductors to avoid danger and damage to the power bank.
7. Power bank needs to be handled with care to avoid collisions, falling, and to prevent damage to the casing and accidents.
8. When charging, keep it in a safe place that children cannot touch.
9. It should not be used without a full charge.
10. Do not cover anything when charging the battery.
11. In case of long-term non-use, it needs to be fully charged and placed off. After 2 months, it needs to be charged again and placed.

Custom Coded Lock Instruction

Change Password

The original password is 0-0-0. To set your own password, follow these steps:

1. Dial the password to the original password: 0-0-0.
2. Press button A with a pen or other tool until you hear the 'tick' sound.
3. Dial the password wheel B to set your own password (e.g., 8-8-8).
4. Push button C in the direction of the arrow and hear the "tick" sound again. Button A will pop up, and the password is set successfully.

You have now completed your password setup; please keep it in mind.

Unlocking Instructions

1. For first-time opening, turn the password wheel to the original password: 0-0-0; push button C in the direction of the arrow. The pull tab will pop out, and the lock will be opened successfully.
2. For daily opening, turn the password wheel to the new password you set (e.g., 8-8-8); push button C in the direction of the arrow. The pull tab will pop out, and the lock will be opened successfully.

Illustration shows the USB charging port and three buttons labeled A, B, C, associated with the TSA coded lock.

Power Switch Indicator

• Flash 1: Motor stall
• Flash 2: Low battery
• Flash 3: General fault
• Flash 4: Battery undervoltage

Illustration shows the Power button and an indicator light.

Maintaining

Appearance Cleaning

1. Vehicles need to be cleaned at any time.
2. When cleaning dust, do not wipe electrical parts and connectors with a damp cloth.

Other Maintaining

1. Lubricate the front and rear axles once every six months.
2. Check and tighten electrical connectors.
3. Verify the brake is workable.

Safety

For all precautions regarding SE3S riding, please read and follow the SE3S requirements. Do not use this product until you have read the instructions carefully to understand the performance of the SE3S. Do not lend it to anyone who cannot operate this product.

Very Important

It is strictly forbidden to accelerate, decelerate, and turn sharply. It is strictly forbidden to ride at excessive speed. Please maintain a low speed during riding. If there is a risk of falling, prioritize your personal safety and do not consider the SE3S. The SE3S may cause wear and tear during riding and parking, which may affect the product's performance. Therefore, before riding the SE3S, you must perform the following checks:

1. It is necessary to check whether the various components of the SE3S are securely installed, without damage, and that the brake function and tires are in good condition.
2. You need to fully understand the surrounding cycling environment: ensure you are not disturbed by cars, pedestrians, pets, bicycles, or other obstacles.

Note:

1. Do not store cash or valuables in your luggage.
2. The safety and reliability of brakes, boxes, wheels, etc., must be confirmed before riding to avoid accidents.
3. Avoid riding on uneven, muddy, rocky roads, slippery roads, waterlogged roads, and stairs to prevent rim deformation and danger.
4. The torch cannot be hung on the ride, to avoid operation of out-of-control accidents.
5. This product is suitable for one-person riding.
6. Overloading and crawling ramps greater than 6 degrees are strictly prohibited.
7. People under the influence of drugs or alcohol, or with limited mobility and responsiveness, are prohibited from riding.
8. Riding is prohibited in cases where it is not suitable due to the cyclist's own reasons or other objective factors.
9. It is important to develop the habit of charging in time daily. Riding with a minimum allowed voltage helps maintain battery life. Battery performance is affected by the environment; discharge performance is better at higher temperatures. Below 0°C, battery power can drop by more than one-third.
10. Therefore, in winter or cold areas, a reduction in mileage after a single charge is normal. When the temperature rises above 20°C, its function naturally recovers. Remove dust from the power plug regularly.
11. Ash accumulation in humid environments can cause fire hazards. Do not damage, force bend, or bundle the power cord.
12. Do not place heavy objects on the power cord or expose it to places that emit excessive heat.
13. Do not insert foreign objects into USB ports, charge-discharge connectors, or other openings of the product.
14. Do not split the individual parts of the luggage yourself.
15. Do not lift the luggage using the lever handle. Lift the luggage when crossing steps or stairs.
16. Pulling the luggage over steps or stairs can cause the luggage to tip over and be damaged.
17. In a moving vehicle, on uneven or sloping surfaces, place the luggage on the ground to prevent it from tipping over and being damaged. Do not place the luggage in damp, unventilated, or acidic environments for extended periods. If wet, dry it promptly.
18. Do not place luggages near high temperatures or fireworks.
19. Do not wipe the luggage with corrosive solvents such as banana water or petroleum concentrate.
20. Do not rinse directly with water and avoid use in rainy days.
21. When closing the luggage, be aware that your body or clothes should not be caught in the case or lock.
22. Be careful of liquid leaks in the luggage, which may cause a short circuit in the inner compartment.
23. The Company is not responsible for the use of charging cables and other accessories not exclusively designed by the Company, nor for accidents resulting from such use.
24. Unauthorized removal or modification of this luggage is prohibited. The Company will not be liable for resulting damage and may revoke your warranty. In case of internal failure, contact aftermarket personnel.

All rights reserved in this manual are the property of the company.