User Manual for TOPBULL models including: D2, 4K UHD 2160P Dash Camera, D2 4K UHD 2160P Dash Camera
D2 User Manual (PDF) TOPBULL TOPBULL 4K,Dash,Cam,Front,and,Rear,UHD,2160P,Dual,Car,Dashboard,Camera,Recorder,with,WiFi,GPS,WDR,Night,Vision,Sony,Sensor,SD,Card,Included,G-Sensor,170°,Wide,Angle,3",IPS,Screen,Speed,Warning,,
File Info : application/pdf, 17 Pages, 406.80KB
DocumentDocument4K UHD 2160P Dash Camera User Manual Customer Service : topbulls@163.com 1. Button introductions Power button Press for 3 seconds to turn on or off, and press for more than 6 seconds to force turn off OK button Short press to start or pause recording UP/WIFI Setting interface: menu UP function Press UP button for 3 seconds to turn on or off WiFi. WiFi is default off Press UP can switch front and rear lens (Note: dual recording mode supports this function) DOWN/Switch Setting interface: menu DOWN function Recording interface: Short press to close and open sound recording MENU button When the recording is paused: short press MENU go to menu function Recording in the start state: short press MENU to lock the current file Reset If the camera has abnormal recording or WiFi disconnection, you can restart the camera by pressing the reset button shortly TF card slot please use 32-256GB (class 10 U3 or above ) TF card 2. Installation guide (1) Turn off the car engine (2) Find a suitable position in the car that does not affect driving, then wipe the surrounding glass, install the bracket and hang the camera (3) Tear off the protective film on the lens, make sure the lens is clean, adjust the lens position, so that the lens and the ground remain at a level (4) Plug one end of the power cord into the power socket of the camera, and the other end into the power socket of the car (5) Start the engine and check if the camera has been installed correctly 3. Recording/ taking pictures instructions Recording Turn on the camera and enter recording mode, the upper left corner of the screen shows the video icon . Start recording, there will be a red dot flashing on the screen under recording status. At the same time in the recording, you can not operate the menu and switch the working mode, then short press OK to stop the recording Taking pictures In the stop recording state, short press MODE to switch to photo mode, the upper left corner of the screen shows the photo icon . Short press OK to take a picture, short press MEMU to enter picture setting, short press MODE to switch to playback mode Video/picture playback In photo mode, press MODE to switch to playback mode, with the playback icon displayed in the upper left corner of the screen Short press on the UP to select the file upwards Short press on the DOWN to select the file downwards Short press the OK to play the selected video file Short press MENU to enter menu setting, where you can delete or unlock files Setting In the three (recording, photo, playback) mode pause state, short press MEMU to enter the menu, and then short press once again to switch to the settings menu . By short press UP or DOWN, select different setting, select the setting that need to be changed, by short press OK to enter to change, then short press the MENU to exit the menu interface 4. Install APP & Connect wifi Install APP (1) Search"LuckyCam"in app store, or scan the follow QR to download the app (IOS-QR-Code) (Android-QR-Code) (2) After install the app will prompt "if you want "LuckyCam" to access the photos of your phone", click "OK" Connect wifi (1) Enter MENU in the pause recording state, press MENU again to switch to Setup menu, select WiFi, select "On", (or long press UP for more than 3 seconds to open WIFI), and then the screen will display the WIFI name and password (No need to enter the password when connecting again) (2) Enter the phone WLAN settings interface, find the camera WIFI such as: NVT_CARDV******, enter the password to connect, WIFI initial password is: 12345678 (3) After the phone and recorder interconnection successfully, you can open the APP to view the real-time screen or recorded video and pictures. (Because this recorder is true 4K pixels, when real-time viewing, pixels will be compressed, to get true 4K HD video, please download the video and then watch) (4) Click APP to enter the download interface, the recorder screen will jump to download transmission interface, back to the APP main interface through the phone, the recorder screen to resume the recording interface (5) Long press UP more than 3 seconds to exit the WIFI, press OK and the recorder will come back to record Video preview When the APP is successfully connected to the recorder, the recorder in the state of stop recording, click the "folder" menu, click to play one of the videos (Note: direct preview will have video progress buffer) Download click" "to download the video to the phone click" "to to see the pictures Note: The video played back by the mobile phone is compressed. If you want to watch the original high-definition video, please download and play it on your mobile phone or insert the TF card into your computer to watch 5. GPS tracker & rear camera GPS tracker (1) The GPS module is a square accessory in the box and must be powered up to work. Connect the power cable to the socket on the GPS, and then connect the GPS to the power socket on the recorder, and then you can use it after plugging in. (2) GPS connection success, there will have a GPS icon on the screen. (3) GPS connection success, the stored video will marked with the corresponding coordinates (longitude and latitude), and the speed of the car (4) When playback the video on the phone, it will play the GPS tracking information (5) The GPS module with tape on this side must be attached to the front windshield so as to receive a stable signal. (Remember not to reverse the paste, otherwise it will disturb the GPS direction) Rear camera (1) Connect the rear camera, the screen will display the rear recording video in real time (2) At the same time, the TF card will save the rear camera video with the file suffix "B" (3) Rear camera should be installed near the license plate. Both the rear viewing and reverse guidance images are sharp and clear. To use the reversing function, please install the rear camera in position 6. Basic settings (1) Resolution: The default video resolution is: 3840*2160+1920*1080 25P The menu also contains 2560*1440+1920*1080 30P and FULL HD, select the corresponding resolution and click OK to switch the resolution. (2160P is true 4K) (2) Loop Recording: default is 3 minutes, click "Loop Recording" menu, the video length can be set to 1 minute / 3 minutes / 5 minutes (3) WDR: default is "On", which means it automatically captures more light and adjusts brightness to produce clear, color-accurate videos and pictures even in low-light conditions (4) G-sensor: the default setting is "medium", which corresponds to the sensitivity of the vibration when the file is locked (5) EV Exposure: default is +0.0, with various options available in the menu (6) Record Audio: The default setting is "On". Turn on video recording, select "Off" to turn off recording (7) Date Stamp: The default setting is "On", which shows the time and date of the recorded video (8) WiFi: default setting "Off", choose "On"or long press UP button to open, connect via mobile app (9) Date/Time: Select the menu to pop up the date and time, manually adjust the current time and date, or connect to the APP settings menu and select time settings, click "Auto Sync" to set the current date and time (10) Auto Power Off: Default setting "Off", menu setting 1min /3min /5min Select "Off", that is, in the state of stopping recording, the camera will not automatically shut down Select "1 minute" that is, in the state of stop recording, the camera will automatically shut down in 1 minute (11) Rear Camera Mirror: default setting "on", that is, whether to pull back into a mirror (12) default is "3 minutes", click to select menu (Off / 1 min / 3 min / 5 min) Select "Off", i.e. the display will be on for a long time Select "1 minute", that is, the display will enter the screen saver black mode after 1 minute (13) Beep Sound: default is "On", that is, to open the key sound (14) Language: default language "English", there are multiple languages in the setting menu (15) GPS: Select "On" to display the GPS symbol icon on the screen, select "Off" to close the GPS symbol icon on the screen (16) Timezone: default time zone is GMT +8:00, the menu can choose the global time zone (17) Speed Warning: The default is 100km/h, you can choose to set between 70140km/h in the menu, that is, after choosing 100km/h, if the vehicle driving speed is greater than this speed, the machine will sound a beep. (GPS must be linked before using this function) (18) Speed Unit: default is KM/H, the menu contains KM/H, MPH optional (19) Frequency: default for 50Hz, the menu contains 50Hz, 60Hz optional (20) Format: formatting select "Confirm" that is to delete all data on the TF card (21) Default Setting: Select "Confirm" that is to restore the factory settings (22) Motion detection: default setting "off", can be set in the APP, such as select "on" that is, in the recorder stop state, sensing the object in front of the movement, the recorder automatically record 10 seconds and then stop.Recorder automatically record 10 seconds after stopping 7. Parameters CPU Imagine sensor Display Pixels HUD Video format Speaker Voltage Memory Operation temperature() language Automatic logging of power on Loop recording WDR GPS Delay shutdown Parking monitor G-sensor Lock Recording Video Code NOVATEK NT96670 SONY STARVIS CMOS 3.0inch IPS 800M (3840*2160+1920*1080) Real 4K MP4 support DC 5V TF card, U3 class10 or above, max support 256GB -20-70 multi-language support support support support support Support, need connect the hardwire kit support support support H.264/H.265 8. Common Problems and Solutions Problem Causes and Solutions Unable to start Make sure the vehicle is in ACC "ON" or ignition Crash Press the reset button to restart Unable to record, send "beep beep beep" alarm Unable to connect No live preview Image lag Settings save error No TF card, TF card failure, or TF card can not be recognized, you can replace the TF card or format the TF card Mobile devices such as cell phones need to be close to the recorder, select the SSID in the settings, and enter the correct password Make sure the connection is normal, reopen the APP after exiting The cell phone APP appears abnormal or program error, re-download and install APP and reduce the software running on the phone Check if the connection is OK Note: TF card formatting As TF card is in working condition, long-term use of TF card will produce fragments or damage, please check and format TF card regularly (Suggestion: check and format TF card regularly every month) 9. Important Notes (1) Please pay attention to set the time zone when you use it for the first time (2) it is recommended to use the original SD card, Samsung and other class 10 or U3 or above TF card to avoid incompatibility problems. (Support 32-- 256GB class 10 U3 or above TF card) (3) because the recorder for true 4K pixels, when playing the recorded video on the computer or TV, please download the 4K special player, it is recommended to download PotPlayer and VLC media player. (If you use a player that does not support 4K video playback, it will cause the video screen lag.) (4) Please use original accessories provided by us, just in case of compatible issues after using other's, especially use 2 or 3 in 1 cigar socket will lead to 100% insufficient current supply (5) Because this product is super capacitor powered, not battery powered, so if you need to use the parking monitoring function must be connected to the buck cable (not included) to the car distribution module, because the installation of the buck cable line is very complex, it is recommended to go to the local auto repair center for installation, the buck cable must be purchased separately. (Battery power supply is easy to age, not resistant to high temperature and cold, and prone to explosion, so super capacitor is more advantageous and safer than battery power supply method.) (6) WIFI connection distance available for 15 feet, more than this distance will automatically disconnect (7) in the use of the recorder encounter problems or difficulties, please contact us first after-sales customer service: topbulls@163.com, we will solve for you as soon as possible 10. Disclaimer Car recorder is an instrument that records the process of driving through video, pictures and sound. Accidents occur only as an auxiliary reference Special note: the car recorder must be in the normal recording state, in order to record the file.But in the following cases will lead to image damage or loss In the video recording, pull out the TF card, will lead to the last video file damage or lost In the video recording, abnormal power failure will lead to the last video file damage or loss Recorder in the recording process suffered a destructive collision will lead to video damage or loss The recorder suffered a violent collision during the recording process, resulting in a loose memory card, which will damage the file or cause the file to be lostWPS 文字