Installation Guide for Sunco models including: SH_M-40W, SH_M-40W Motion Shop Light, Motion Shop Light, Shop Light
Installation Guides, Manuals, and Specs | Sunco – Sunco Lighting
LED Shop Lights, Motion Activated | LED LIGHTING | SUNCO – Sunco Lighting
CEC Title 20 and Title 24 Efficiency Regulations – Sunco Lighting
File Info : application/pdf, 2 Pages, 1.47MB
DocumentDocumentMOTION SHOP LIGHT Install Guide and Manual COMPONENTS X2 Chain Link X4 "S" Hook X2 Screw Eye Hook X6 Plastic Anchor X4 Screw EASY INSTALLATION SUSPENSION INSTALL Turn Power OFF 1. Turn off circuit breaker that provides power to the light switch for the recessed lights. 2. Mounting surface must be able to support the weight of the fixture. ·Plaster board - #8 eye hook screw with plastic anchors, or expansion bolts (not included); ·Plaster board thickness should be 3/8 inch. 47.25" apart Connect to Power Outlet Connect to additional shoplight Link up 8 shoplights together 4. Depending on your lighting plan, space the anchors accordingly. ·Link up to 4 Step A Step B Required Tools: Drill, Ladder, Hammer, Pliers, Tape Measure, Pencil. 3. Attach two anchors to ceiling. Spacing between hooks should be 47.25 inches apart, then screw in the screw eye hooks into the anchors. 5. Install one S hook into each end of the chain (A), then crimp the end attached to the chain with pliers (B). Leave the other side open. 6. Install the S hook from one end of the chain into the end cap, then crimp the hook with pliers. Repeat on the other side. End 7. Hang the loose end of the S hook chain on the screw eye hook in the ceiling. 8. Plug in power cord to electrical outlet. 9. Turn on circuit breaker and test light. Side WARNING To reduce the risk of fire, electric shock or injury to people: ·This product should be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. ·Abide by related regional and local laws or regulations. ·Proper grounding is required to ensure safety. ·Check for damage during shipping prior to install. If the product is damaged do not use it. ·Turn off the switch and circuit breaker before installing this LED light fixture. ·To ensure efficient light, regularly clean the light panel.Do not clean with harsh solvents. ·Use safety precautions. Safety eyeglasses and gloves are recommended. ·Risk of fire or electric shock. Do not alter, relocate or remove wiring during installation. ·This fixture complies with Part 15 of the of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. ·NOT for use with dimmers. Do not install directly over a heat source. ·Please review instructions carefully before proceeding. Turn Power ON SPECIFICATIONS Voltage Wattage Suitable for Locations Ingress Housing Weight Warranty 120V 40W Damp Steel+PC 2.70lbs 7 years MOTION SHOP LIGHT Install Guide and Manual COMPONENTS X2 Chain Link X4 "S" Hook X2 Screw Eye Hook X6 Plastic Anchor X4 Screw EASY INSTALLATION DIRECT MOUNT INSTALL Turn Power OFF 1. Turn off circuit breaker that provides power to the light switch for the recessed lights. 2. Mounting surface must be able to support the weight of the fixture. ·Plaster board thickness should be 3/8 inch. Connect to Power Outlet Connect to additional shoplight 4. Depending on your lighting plan, space the anchors accordingly. ·Link up to 4 Link up 8 shoplights together 0.33" 0.14" 46.5" apart 3.189" Required Tools: Drill, Ladder, Hammer, Pliers, Tape Measure, Pencil. 3. Install 4 plastic anchors 46.5 inches apart and 3.189 inches apart, screw in a screw into each anchor. The gap between the ceiling and the cap nut should be 0.75 inch. ·Recommended screw dimensions: ST4X30 ·Gap needed for keyhole slots 5. Lift fixture up to screws and slide to one side to secure into place. Fixture should be firmly fixed against screws. If not, tighten screws. 6. Plug in power cord to electrical outlet. 7. Turn on circuit breaker and test light. Turn Power ON PIR MOTION SENSOR DETAILS Light will turn on when movement is detected within range of motion. ·Use a tape measure to determine placement of fixture. See chart bellow for sensitivity. Light will turn off auatomatically 10 minutes after detected movement has stopped. STYLE 1 AND STYLE 2 OF INFRARED INDUCTION RANGE STYLE 1 The recomended installation height is OC 9.18-11.48ft (2.8~3.5m) STYLE 2 The recomended installation height is OC 9.18-11.48ft (2.8~3.5m) Human infrared sensor Movement in this direction sensing distance OA/OB<6.56ft (<2m) Movement in this direction sensing distance OB<16.4ft (<5m) Human infrared sensor Movement in this direction sensing distance OA/OB<6.56ft (<2m) Movement in this direction sensing distance OB<16.4ft (<5m)