UBeesize TR67 Professional Video Tripod User Manual
Official website: www.ubeesize.com
Customer service contact: customercare@ubeesize.com
Thank you for choosing Ubeesize. Please read this manual sheet before using.
Tripod Assembly and Features
1. Vertical Lock: Secures the vertical position of the center column.
2. Gear Center Column: Allows for precise height adjustment of the center column.
3. Center Column Lock: Tightens or loosens the center column for height adjustment.
4. Foam Sleeve: Provides grip and insulation on the center column.
5. Flip Lock: Lever mechanism to extend or retract leg sections.
6. Center Column: The main vertical support of the tripod.
7. Sleeve: Part of the leg structure.
8. Rubber Pads: Located at the bottom of the legs for stability and grip.
9. Angle Lock: Adjusts the angle of the tripod legs.
10. Hook: Located at the bottom of the center column for hanging weights.
11. Handle Bar: For carrying or adjusting the tripod.
12. Pan Lock Screw: Secures the panning movement of the head.
1. Tripod Introduction
2. Use of the Quick Release Plate: To remove the quick release plate, squeeze and pull the plate locking lever out. The Quick Release Plate will disengage allowing it to be removed.
3. Vertical Panning, Horizontal Rotation, and 90 Degree Shot:
- a: Rotating the panning adjustment knob loosens for smooth panning and tightens when rotated oppositely.
- b: Rotating the tilt adjustment knob loosens for smooth tilting and tightens when rotated oppositely.
- c: Rotating the rolling lock knob adjusts the angle of the loading plate. Flip up to 90 degrees. Rotate oppositely to tighten.
4. Raising and Lowering the Center Column: Turn the center locking knob counter-clockwise to set the column to the desired position. Hold the column and turn the knob clockwise to secure it. Do not overtighten.
5. Extend and Fold the Leg: Open the Flip Lock Lever to extend or retract leg sections. Snap the lever closed to lock. Repeat for each leg and section.
6. Weight Hook: Use the retractable weight hook to hold a sandbag or camera bag for added stability in windy conditions. Do not overload the tripod.
Warnings
Do not exceed the tripod's maximum load capacity.
Ensure the ballhead is locked.
Do not operate this tripod when the temperature is below -20° C or above 70° C. It is not recommended to operate in saltwater.
Do not put this tripod in sunlight or lean it against the glass of a car for a long time.
Do not leave this tripod unattended in public places; please be careful when use it in dangerous places.
Remove the camera from the ballhead during setup or transport.
It is not necessary to equip lubricant. Please use standard lubricant or grease when necessary.
For your safety, keep it out of power supply.
Bluetooth Remote Shutter
Cellphone Clamp
Supporting Range: 2.3-3.6 inches
Assembly
8. Remove the quick release plate.
9. Assemble the plate with phone mount using the 1/4 screw interface.
10. Fasten the ring at the bottom of the quick release plate to secure the phone mount.
Step 1 Pairing
- A. Turn the remote on with the power switch located at the side. The blue LED light will flicker.
- B. Turn on your phone's Bluetooth setting & connect to "Bluetooth remote RL7" in the available devices list. The blue LED light will stop flickering when connected.
Step 2 Using
Open your phone's camera app. Press the button associated with your phone's operating system (iOS for iPhone, Android for Android Phones).
Note: If your camera does not respond, it may not be compatible. In this case, download the free app "Camera 360" and use this camera app with the remote.
Step 3 Filming Videos
Switch your phone's camera into Video mode first. Press the button to start/stop recording videos.
Note for Samsung Cell Phones:
- Go to camera setting, scroll down and tap "Volume keys function" and choose "Record video".
- Open the native camera, click the iOS button (Not Android) to start the video, click again to stop the video.
Additional Warnings
Do not exceed the tripod's maximum load capacity.
Ensure the ballhead is locked.
Do not operate this tripod when the temperature is below -20° C or above 70° C. It is not recommended to operate in saltwater.
Do not put this tripod in sunlight or lean it against the glass of a car for a long time.
Do not leave this tripod unattended in public places; please be careful when use it in dangerous places.
Remove the camera from the ballhead during setup or transport.
It is not necessary to equip lubricant. Please use standard lubricant or grease when necessary.
For your safety, keep it out of power supply.
