Instruction Manual for Godox models including: RT-16, RT16, 2ANIV-RT-16, 2ANIVRT16, RT Series, Studio Flash Trigger
Shenzhen Neewer Technology Co., Ltd RT-16 TRIGGER 2ANIV-RT-16 2ANIVRT16 rt 16
GODOX
:
GODOX_RT
705-RT0000-00
(mm) 390x120mm
(mm)
±2mm
128g
/
Studio Flash Trigger
RT Series
Instruction Manual
Foreword
Thank you for purchasing RT Series Studio Flash Trigger. It is a control discreteness for camera to trigger studio flashlight synchronously. The device is composed of two parts, namely signal transmitter and receiver.
Contents
Foreword For Your Safety Names of Parts
Body Accessories Battery Channel Settings
Instructions for Use Function Introduction Connection Operation
Technical Data Attentions Maintenance
For Your Safety
To prevent damage to the product or injury to you or to others, read the following safety precautions in their entirety before using this equipment. Keep these safety instructions where users can read them for ready reference.
Do not disassemble or modify Failure to observe this precaution could result in electric shock or product malfunction. Should the product break open as the result of a fall or other accident, remove the batteries and take the product to authorized maintenance center for inspection. Keep dry Do not handle with wet hands or immerse in or expose to water or rain. Failure to observe this precaution could result in fire or electric shock.
Keep out of the reach of children This device contains small parts that may pose a choking hazard. Consult a physician immediately if a child swallows any part of this device. Do not expose to high temperature Do not leave the device in a closed vehicle under the sun or in other areas subject to extremely high temperature. Failure to observe this precaution could result in fire or damage to the casing or internal parts.
Names of Parts
Body 7 6 8 5 9 1 2
3 4
Receiver (1)Trigger Output Plug (2)Receiving Indicator Lamp (3)Power Switch (4)Channel Code Switch (subject to different model, unavailable for AT-01 )
Accessories 1. Convert Adapter 2. Instruction Manual
Transmitter
(5)Test Button (6)Channel Code Switch (subject to different model, unavailable for AT-01 ) (7)Camera Hot Shoe (8)Sync Cord Jack (9)Transmitter Indicator Lamp
Batteries and Installation
Transmitter: Slide the battery-chamber cover from the back of the transmitter and insert one 12V/23A battery (provided by manufacturer) Receiver: Slide the battery-chamber cover from the back of the receiver and insert two AAA 1.5V alkaline batteries (available separately).
Low Battery Indicator LED indicator on receiver will blink fast when the batteries are low. Please change batteries before they run down in case of flash failure or flash missing. Replacing Batteries When replacing batteries on transmitter or receiver 1.Turn the camera off and disconnect the receiver 2.Remove the batteries with new ones When the device is not in use 1. The transmitter consumes little power and can last over three years when it is in spare without any operation. 2. The receiver is equipped with a power on/off switch. To reduce the drain on the batteries when the device is not in use, please slide the power to OFF position.
Channel Settings There are16 channels in this device. Set the transmitter and receiver on the same channel before use. Check the table for channel setting as below:
channel 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
S1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 S2 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 S3 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 S4 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Instructions for Use
Function Introduction RT Series Studio Flash Trigger is based on a wireless remote system. The transmitter enjoys an advanced electric circuit which is designed with sleepy function, so it has very low power consumption. The receiver is used with alternating current, and it achieves quick response under the advanced MCU control. It can meet the need of sync flash for any different shutter camera. Connection 1.Insert the trig output plug (1) of the receiver into the synch control socket of the strobe.
2.Turn on the power switch (3) of the receiver.
Operation 1.Adjust the same state for the channel code switch (4) (6) for the transmitter and receiver.
2.Press the test button (5), and the transmitter indicator lamp (9) and the receiving indicator lamp (2) will turn red. Simultaneously the strobe will flash to work.
3.Attach the transmitter onto the camera hot shoe mount and press the camera shutter for instant using(corresponding function setting is required for camera).
4.If the camera has no Hot Shoe Jack, insert one end of the synchronous line into the Socket for Synchronous Line (8) and the other end into the Synchronous jack of the camera.
Technical Data
Model
RT-01 RT-02 RT-04 RT-16
Channel
1
2
4
16
Transmit frequency
433MHz wireless remote system
Transmitter power
12V 23A lithium-ion battery
Receiver power Sync socket
3V (AAA*2) 6.35mm / 3.5mm
Outdoor operation distance
30 m (Open space)
Indoor operation distance
20 m (Open space)
Sync speed
1/200 sec
Transmitter Dimension Receiver Dimension
60*42*30mm 77*33*22mm
Attentions
Unable to trigger flash or camera shutter. Make sure the transmitter and receiver are set to the same channel, and the PC cord or the hot shoe mount is completely connected.
Signal disturbance or shooting interference. Change different channel on the device.
Operating distance limited or flash missing. Check if the battery is exhausted. Try to change the battery.
Keep away from strong magnetic field. The strong static or magnetic field produced by devices such as radio transmitter leads to malfunction.
Maintenance
Avoid falling The device may malfunction after strong shocks or under excess stress.
Keep dry The production isn't water-proof. It will lead to malfunction if soaked in water or exposed in high humidity, which cause malfunction and rust, corrosion.
Avoid sudden temperature changes such as the circumstance when taking the remote control out of a building with higher temperature to outside in winter. This may lead to condensation of moisture. Please put the remote control in handbag or plastic bag to prevent sudden temperature changes.
Made In China
705-RT0000-00
Corel PDF Engine Version 16.0.0.707