Installation Guide for HD Ridez models including: WB-NR095BD Black Overland Slider Tubular Drop Steps Style Nerf Bars Running Boards, WB-NR095BD, Black Overland Slider Tubular Drop Steps Style Nerf Bars Running Boards, Slider Tubular Drop Steps Style Nerf Bars Running Boards, Steps Style Nerf Bars Running Boards, Nerf Bars Running Boards, Bars Running Boards, Running Boards
APS Black Overland Slider Tubular Drop Steps Style Nerf Bars Running Boards Compatible with Nissan Frontier 2005-2024 Crew Cab : Automotive
INSTALLATION INSTRUCTIONS RS6 OVERLAND SLIDER DROP STEPS 05-24 NISSAN FRONTIER CREW CAB PART#WB-NR095BD PARTS LIST: 1 Driver/Left Tube 1 Passenger/Right Tube 4 Drop Steps 1 Driver/Left Front Mounting Bracket 1 Passenger/Right Front Mounting Bracket 2 Driver/Left Rear Mounting Brackets 2 Passenger/Right Rear Mounting Brackets 12 10mm x 30mm Hex Bolts (2) Passenger/Right Rear Mounting Brackets Passenger/Right Front Mounting Bracket RS6 OVERLAND SLIDER DROP STEPS 05-24 NISSAN FRONTIER CREW CAB 24 10mm x 20mm OD x 2mm Flat Washers 12 10mm Nylon Lock Nuts 8 8mm Triangle Double Bolt Plates 12 8mm x 24mm OD x 2mm Flat Washers 16 8mm x 22mm OD x 2mm Flat Washers 16 8mm Nylon Lock Nuts 12 8mm Serrated Flange Nuts (2) Driver/Left Rear Mounting Brackets Passenger/Right Tube Driver/Left Front Mounting Bracket (4) Drop Steps Front PROCEDURE: 1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. CLEAN MOUNTING STUDS WITH WIRE BRUSH TO REMOVE PAINT AND DEBRIS. 2. Starting on the Passenger/Right front of the vehicle, (Figure 1). Attach (1) Mounting Bracket to the front location with (2) 8mm Flat Washers and (2) 8mm Flange Nuts, (Figure 2). Do not tighten hardware. 3. Repeat Step 2 to attach (2) Mounting Brackets to the Passenger/Right center and rear locations, (Figure 3). 4. Select the Passenger/Right Tube. Insert (2) 8mm Triangle Double Bolt Plates into the front (2) sets of (2) holes, (Figure 4). Attach (1) Drop Step to the (2) Double Bolt Plates with (4) 8mm x 22mm Flat Washers and (4) 8mm Nylon Lock Nuts, (Figure 5). Do not tighten hardware. 5. With assistance, line up the mounting tabs in the Passenger/Right Tube to the rear faces of the Mounting Brackets. Secure the Tube to the Mounting Brackets with (6) 10mm Hex Bolts, (12) 10mm x 20mm Flat Washers and (6) 10mm Nylon Lock Nuts, (Figure 6). Do not tighten hardware. 6. Level and adjust the Overland Step, then tighten all hardware. 7. Repeat Steps 1--6 to attach the Driver/Left Overland Step. 8. Do periodic inspections to the installation to make sure that all hardware is secure and tight. To protect your investment, Do not use any type of polish or wax that may contain abrasives that could damage the finish. Mild soap may be used to clean the Overland Sliders. Page 1 of 3 10/12/22 (EL) RS6 OVERLAND SLIDER DROP STEPS 05-24 NISSAN FRONTIER CREW CAB Passenger/Right Side Installation Pictured Front (Fig 1) Passenger/Right side front mounting location (2) 8mm Flat Washers (2) 8mm Flange Nuts Front (Fig 2) Attach (1) Mounting Bracket to the Passenger/Right front location Rear (Fig 3) Passenger/Right side rear mounting location Page 2 of 3 10/12/22 (EL) RS6 OVERLAND SLIDER DROP STEPS 05-24 NISSAN FRONTIER CREW CAB Passenger/Right Side Installation Pictured (Fig 4) Insert (1) Triangle Bolt Plate into the holes in the Tube 8mm Bolt Plate (2) 8mm x 22mm Flat Washers (2) 8mm Nylon Lock Nuts Front (Fig 5) Attach (1) Drop Step to (2) Bolt Plates (2) 10mm Hex Bolts (4) 10mm Flat Washers (2) 10mm Nylon Lock Nuts (Fig 6) Attach the Passenger/Right Overland Slider to the (3) Mounting Brackets Page 3 of 3 10/12/22 (EL)WPS 文字