BuzziSurf Installation Manual
For 220-240V Models
Product Overview
This document provides installation instructions for the BuzziSurf lighting fixture, designed for 220-240V power supplies. It is available in Small, Medium, and Large sizes, with both Globe and Spot diffuser options.
Technical Information
? LED Technology
? Suitable for indoor use.
? Earth connection is required.
?? The light source is not replaceable.
✅ CE Certified
Power Factor: >0.8
Input Current: Max 0.35 Amp
Environmental Protection
?️ Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Important Note: The light source of this luminaire is not replaceable. When the light source reaches its end of life, the whole luminaire shall be replaced.
Items Not Included
The following items are not supplied with the BuzziSurf fixture and must be provided by the installer:
- Screwdriver (Phillips head)
- Screwdriver (Flathead)
- Pencil
- Tape Measure
- Drill
- Allen Key
- 2x Wall Plugs
- 2x Screws
Diagrams on page 3 illustrate these excluded tools and hardware.
Included Components
The package contains the following components, with quantities varying by model and configuration:
- Main Luminaire Body
- Mounting Bracket (1x)
- Mounting Screws (2x)
- Wire Connectors (quantity varies, e.g., 1x or 4x)
- Cable Ties (2x)
- Wire Sleeves/Nuts (2x)
- M6 Threaded Rods (2x)
Diffuser Options:
- Globe Diffuser: 1x (Small), 3x (Medium), 5x (Large)
- Spot Diffuser: 1x (Small), 3x (Medium), 5x (Large)
Diagrams on pages 4, 5, and 6 show the included parts for different BuzziSurf variants.
Product Variants and Page References
The BuzziSurf is available in three sizes, with specific installation details referenced:
- BuzziSurf Small: Installation steps begin on page 8.
- BuzziSurf Medium: Installation steps begin on page 16.
- BuzziSurf Large: Installation steps begin on page 16.
Diagrams on page 7 provide a visual overview of the Small, Medium, and Large models.
Installation Instructions
Installation typically requires two persons (?).
Step 1: Turn Off Power
Before starting, ensure the main electrical power supply is turned OFF at the circuit breaker. The image shows a hand switching off circuit breakers labeled 'OFF'.
Diagram shows a hand pressing down on circuit breaker switches labeled 'OFF'.
Step 2: Mark Drilling Points
For BuzziSurf Small: Measure and mark the drilling points on the ceiling. The required distances are 48 cm between the outer points and 18 cm between inner points. Use a pencil and tape measure.
For BuzziSurf Medium & Large: Specific measurements are indicated, such as 'Trio 75 cm | Quintet 150 cm' and 'Trio 28 cm | Quintet 36 cm'. Use a pencil and tape measure to mark these locations.
Diagrams show a drill, tape measure, and pencil, with markings indicating hole placement for mounting. Specific dimensions are shown for Small, Medium, and Large models.
Step 3: Prepare Mounting Points
Insert wall plugs into the marked holes. Then, screw in the mounting screws partially, leaving them extended for attaching the bracket. An Allen key may be used for this process.
Diagram shows wall plugs being inserted into holes and screws being partially screwed in, with an inset showing an Allen key.
Step 4: Attach Mounting Bracket
Align the mounting bracket with the prepared screws and secure it firmly to the ceiling by tightening the screws. An inset shows a screwdriver tip.
Diagram shows the mounting bracket being attached to the ceiling with screws.
Step 5: Prepare Suspension Cables
Feed the suspension cables through the canopy. Adjust the length of the cables as needed. The diagram shows a cable being fed through a component and an arrow indicating adjustment.
Diagram shows suspension cables being fed through a component, with arrows indicating adjustment.
Step 6: Connect Suspension Wires
Secure the suspension wires to the fixture body using the provided wire nuts or connectors. The diagram shows a wire being inserted and secured.
Diagram shows a wire being fed through a connector and secured with a screw-like mechanism.
Step 7: Attach Luminaire Body
Connect the luminaire body to the mounting bracket. This may involve aligning and securing it with screws or other fasteners.
Diagram shows the luminaire body being lifted and attached to the mounting bracket.
Step 8: Electrical Connection (Earth)
Connect the earth wire from the luminaire to the corresponding earth terminal in the ceiling junction box. The diagram shows the earth symbol and a wire being connected.
Diagram shows the earth connection point and a wire being connected.
Step 9a: Dimmable Connection
For dimmable function (compatible with 1-10V, DALI, DMX, DST): Connect the wires according to the color coding: Blue wire to Neutral, Brown wire to Line, Red wire to DIM+, and Black wire to DIM-. Ensure conductors are stripped to approximately 10 mm (0.4 inches) before inserting into the connectors. The diagram shows the wiring connections and a close-up of stripping a wire.
Diagram shows wire connectors with wires (Blue, Brown, Red, Black) connected to terminals labeled Neutral, Line, DIM+, DIM-. An inset shows how to strip a wire.
Step 9b: Non-Dimmable Connection
For non-dimmable function: Connect the wires: Blue wire to Neutral, Brown wire to Line. Red and Black wires are not used. Ensure conductors are stripped to approximately 10 mm (0.4 inches) before inserting into the connectors. A warning symbol indicates not to remove a specific part of the connector.
Diagram shows wire connectors with wires (Blue, Brown) connected to terminals labeled Neutral, Line. Red and Black wires are shown disconnected. An inset shows how to strip a wire, and another shows a warning not to remove a connector component.
Step 10: Secure Canopy
Attach the luminaire's canopy to the mounting bracket, covering the electrical connections. Secure it with screws.
Diagram shows the canopy being attached to the mounting bracket with screws.
Step 11: Attach Diffuser
For Globe models: Screw the Globe diffuser onto the luminaire body. The diagram shows a globe being screwed on.
For Spot models: Attach the Spot diffuser to the luminaire body. This may involve aligning and twisting it into place. The diagram shows a spot diffuser being attached with a twisting motion.
Diagrams show the attachment of both Globe and Spot diffusers.
Final Adjustments and Warnings
Adjust the suspension cables to the desired height. Ensure all connections are secure. The diagram shows arrows indicating adjustment of suspension cables and a warning symbol with a crossed-out lamp, reinforcing that the light source is not replaceable.
Diagrams show suspension cable adjustment and a warning icon indicating the non-replaceable nature of the light source.
