Attica 4x4 – Attica 4x4 | Embrace the Adventure
Instruction Manual for ATTICA models including: ATTJL01B109-BX Apex Series Rear Bumper, ATTJL01B109-BX, Apex Series Rear Bumper, Rear Bumper, Bumper
File Info : application/pdf, 9 Pages, 10.79MB
DocumentDocumentATTJL01B109-BX Before installation - Read and understand all instructions, warnings, cautions, and notes contained in this installation instruction guide. Consult your vehicle owner's manual for proper disconnection of electrical and li ting of vehicle if required for installation of this product. This install may require some technical skills and knowledge of basic mechanical work. If you do not feel that you are capable of performing this install please take this product to a trained professional. A ter reading this guide please contact us with any questions or concerns before installing product. Customer Service: (626) 369-2121 ATTICA4X4 is not responsible for any bodily injury or harm to you or your vehicle as a result of an improper install. Proper installation of this kit requires knowledge of the factory recommended procedures for removal and installation of original equipment components. We recommend that the factory shop manual and any special tools needed to service your vehicle be on hand during the installation. Installation of this kit without proper knowledge of the factory recommended procedures may affect the performance of these components and the safety of the vehicle. Always wear eye protection when operating power tools. Inspect all contents of this package to make sure product is not damaged and all installation hardware has been included. If parts are missing from kit, please be prepared to provide the following information: · Name of purchase location · Bar Code on side of box · Date above Bar Code · Date insde box cover tech@attica4x4.com (626) 369-2121 · 10mm socket · 18mm socket · 21mm socket · 4mm hex tool tools required hardware kit x 2 Nut Bracket x 4 w27 | washer x 4 b55 | Bolt x 6 w36 | lock washer x 4 n29 | nut x 4 w25 | lock washer x 6 w35 | washer x 4 b37 | bolt x 6 b56 | bolt x 1 SPARE PARTS HARDWARE KIT 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM Begin by unpacking all items and inspecting them for damage or missing items. Any concerns, please contact the company you purchased the bumper from. A ter inspection, remove your factory rear bumper. Transfer your parking sensors to Attica Apex Series Rear Bumper using the B55 bolts | N29 nuts | 10mm Socket. Begin by placing your threaded plate as shown. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM Please Note: Some model's of the Wrangler JL have a threaded insert located where your threaded plate should go. If so, do not panic, just flip your threaded plate over and only fasten the outermost nut as shown above. Once your threaded plate(s) are in position, proceed with inserting your rear bumper into place. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM A ter mounting your rear bumper, use B56 bolts, W36 lock washer and W35 washer. Lorem ipsum 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM Once you are done hand-tightening the bolts on both sides of your rear bumper, it should mirror what is shown to the le t. Use B37 bolts, W25 lock washer and W27 washer into both under-sides of the bumper. Please note: Some model's of the Wrangler JL have a threaded insert located where your threaded plate should go. If so you will need to proceed with using B56 bolt, W36 lock washer & W35 washer in the same location where the threaded insert resides as shown on the right. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM A ter all your bolts are hand-tightened. Proceed with tightening the B37 bolts on both sides of the rear bumper with your 18mm Socket to help your li t bumper into position. Please note: Use your 21mm Socket for bottom B56 bolt if needed. Once your B37 bolts are tightened, continue with tightening the B56 bolts on both sides of your rear bumper by using your 21mm Socket. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM Finally, your Attica Wrangler Apex Series Rear Bumper is fully installed and ready to hit all forms of terrains. 13942 VALLEY BLVD, CITY OF INDUSTRY, CA 91746 TECH@ATTICA4X4.COM 626-369-2121 WWW.ATTICA4X4.COM if you have any questions, please email us at tech@attica4x4.com or call us at 626-369-2121 tech@attica4x4.com (626) 369-2121