NETGEAR Nighthawk M6 5G Mobile Router

Download Resources

To download the user manual, scan the QR code or visit http://www.netgear.com/m6usermanual.

To see warranty information, scan the QR code or visit https://www.netgear.com/au/mr6110warranty.

Safety First

Please read all safety notices before using this device. This device is designed to be used at least 5 mm from your body. Do not use the device near fuel or chemicals or in any areas such as service stations, refineries, hospitals, or aircraft. Obey all warning signs where posted.

Radio frequency safety information: The device includes an internal antenna. For optimum performance with minimum power consumption, do not shield the device or cover it with any object. Covering the antenna affects signal quality, might cause the router to operate at a higher power level than needed, and might shorten battery life.

Radio frequency energy: Your wireless device is a low-power radio transmitter and receiver. When switched on, it intermittently transmits radio frequency (RF) energy (radio waves). The transmit power level is optimised for best performance and is automatically reduced when there is good quality reception. Maximum power is used only at the edge of network coverage, so under most circumstances the power output is very low. Under poor network conditions, the device transmits at a higher power, and might get hot, and battery life might be significantly shorter.

Declaration of conformity - specific absorption rate (SAR): Your device is designed to be used at least 5 mm from the body. NETGEAR declares that the product detailed in this manual, and in combination with its accessories, conforms with the essential requirements of the Radio Communications Standard (Electromagnetic IC Radiation Human Exposure) 2003 and the Australian Communications and Media Authority Section 376 of the Telecommunications Act 1997 when used at a distance of not less than 5 mm from the body.

What's in the box

• Nighthawk® M6 5G Mobile Router
• Battery cover
• Battery
• USB Type C cable
• AC adapter

Get to know your mobile router

The mobile router features the following components:

• Touch screen: For interacting with the router's interface.
• Back/Home buttons: For navigation.
• Power button: Press and hold for 2 seconds to turn on/off.
• External antenna port (TS-9): For connecting external antennas.
• USB Type C port: For charging and data transfer.
• Ethernet port: For wired network connection.

Install the battery

1. Verify the SIM orientation as shown on the product label.
2. Insert the nano SIM card. The nano SIM card must have an active data plan with your operator.
3. Insert the battery.
4. Install the back cover.
5. To charge the battery, connect the USB cable to the mobile router and then plug it into either:
   • A wall socket, using the AC adapter (faster charge option).
   • A USB port on your laptop.

Set up your mobile router

1. Press and hold the Power button for 2 seconds.
2. To better safeguard your network, the first time you turn on your mobile router, you are asked to set up your login credentials.
3. Follow the onscreen instructions to customize your mobile router settings.

LCD home screen

The home screen displays your mobile router's WiFi network name and password, and the mobile network signal strength and connection type.

Key indicators include:

• Signal strength: Indicates the quality of the mobile network connection.
• Mobile network: Shows the network type (e.g., 5G) and carrier.
• Battery: Displays the current battery level.
• WiFi network name and password: Your network credentials.
• QR code for quick connect to WiFi: Allows easy connection of devices.

Use the battery or AC power

This mobile router can operate on battery when you're away from your home or the office. The Power Manager settings allow you to further optimize battery life.

This mobile router can also operate without a battery using the supplied AC adapter. For extended periods on AC power, it is recommended to remove the battery to extend its lifespan.

Connect to the Internet

The mobile router LCD screen goes dark to save power. A quick press and release of the Power button wakes the screen.

QR code connect from a smartphone

1. Tap the QR code icon on the mobile router's LCD home screen. A QR code displays.
2. Point your phone's camera at the QR code. Your phone connects to the mobile router WiFi network.

On your laptop or other WiFi-capable device

1. Open your WiFi network manager.
2. Find your mobile router's WiFi network name (e.g., NTGR_XXXX) and connect.
3. Enter your mobile router's WiFi password.

Note: To reduce power consumption and extend battery life, this mobile router has Ethernet disabled by default. You can go to Power Manager to change to custom profile settings.

LCD Settings

View or change the settings:

On the home screen, tap the Settings tile. From the Settings page, tap Airplane Mode, Security, Mobile, or Screen to view or change the settings. Tap Messages to view or delete SMS messages. Tap More to view device Information and other settings.

Support and Community

From the Web Admin Portal home page, click the [More options icon] in the upper-right corner to access help and support files.

Contact your service provider regarding warranty and support information for this product.

For additional information, visit netgear.com/support to access the user manual and to download firmware updates.

You can also check out the NETGEAR Community for helpful advice at community.netgear.com.

Regulatory and Legal

For regulatory compliance information, visit https://www.netgear.com/about/regulatory/. See the regulatory compliance document before connecting the power supply.

For NETGEAR's Privacy Policy, visit https://www.netgear.com/about/privacy-policy.

By using this device, you are agreeing to NETGEAR's Terms and Conditions at https://www.netgear.com/about/terms-and-conditions. If you do not agree, return the device to your place of purchase within your return period.

LCD WiFi Manager

You can manage the WiFi network and change the WiFi settings from the LCD screen.

Change the WiFi network name and password

1. On the home screen, tap the WiFi tile.
2. Tap WiFi and select an available WiFi network.
3. Tap WiFi Name, enter your changes, and tap Done.
4. Tap WiFi Password, enter your changes, and tap Done.

If your device is not connecting to this mobile router, it is suggested enabling Dual-Band (2.4 & 5 GHz) in WiFi Band settings.

Note: To reduce power consumption and extend battery life, this mobile router is default set to the WiFi 5 GHz Only band.

Web Admin Portal

You can use a web browser to view and change more advanced mobile router settings.

Log In

1. To find the URL for the Web Admin Portal, on your mobile router, tap Settings > More > Device Information. The URL displays. It is either http://mywebui.net or http://192.168.1.1.
2. On a WiFi-capable device that is connected to your mobile router, type the URL in the browser bar.
3. Log in as administrator.

Note: The default administrator login is printed on the mobile router label, which is inside the battery compartment.

Manage settings using the NETGEAR Mobile app

Use the NETGEAR Mobile app to change your WiFi network name and password. You can also use it to play and share media, and access advanced mobile router features.

1. Make sure your mobile device is connected to the Internet.
2. To download the NETGEAR Mobile app, scan the QR code below. The QR code connects you to the Apple Store or Google Play Store, depending on your mobile device.