User Guide for VideoRay models including: 72281, PRO 5 Mission Sensor System, PRO 5, Mission Sensor System, Sensor System
VideoRay Mission Specialist Pro 5 | Nautikaris
PRO 5 Quick Reference Guide 1 Visually Inspect the System 1A Check the thrusters. GOOD Inspect the propellers, verifying that each has 3 WORN blades and they are free to spin. 1B Inspect for water inside the camera housing. Inspect the thruster telltales and look for signs of oil leakage. 1C Inspect the entire system for signs of damage, loose, or worn parts. VideoRay Part Number 72281 rev 5.01.00 2021-09 2 Connecting & Powering On WARNING: Do not connect or disconnect cables while system is powered. CAUTION: ALL ROV submerged connections must be terminated. CAUTION: Follow these steps in order when starting the system. Connecting the System 1. Remove the tether caps and connect the female end of the tether and strain relief to the ROV. See figure 2B. (Store caps in a secure location) 2. If not already connected, connect the male end of the double ended connector 26A to the Operator Control Console (OCC). 26 3. Connect the male end of the tether to the female end of the double ended connector. 26B 4. Remove the ROV float block bolts and remove the float block. 5. Inspect all 5-pin and 9-pin connectors to ensure they are seated and then Replace and secure the float block. See figure 2C. CAUTION: If the connectors are not fully seated, clean, lubricate, and reseat them. 6. Connect the hand controller to the OCC controller USB port. 24 CAUTION: Do not connect more than one hand controller to the system at a time. 7. Connect the keyboard to the OCC keyboard USB port. 25 8. Confirm that the ROV POWER MAINS is fully depressed. 9. Connect the OCC power cord to the OCC and a power source. 18 ON 10. Turn on the OCC. 19 11. Turn on the ROV POWER MAINS. 20 Twist the Red Power Mains button clockwise. 12. Start the Pro 5 control software. Pro 5 2A Attach the strain relief bolt through the eye hole of the strain relief cable. 34 2B Test the strain relief to verify the stress is on the cable not the tether or connector. 35 2C If the connectors are separated, do not place the system in water. Clean, lubricate and reseat the connectors. BAD GOOD 3 Pre Dive Check List Using the Controller / Testing the System: 1. Verify all thrusters respond to the controller inputs as expected. M J 2. Verify main camera tilts all the way up and all the way down. F G 3. Verify main camera focus - in and out. H I 4. Verify LED light function. Both LED modules dim until off and increase until full illumination. E 5. Deploy Vehicle and adjust ballast. NOTE: It is okay to lower the vehicle using the tether To ballast the ROV: Add or remove ballast weights 12 until the ROV is slightly positively buoyant. Typically, this is achieved when the top of the float block is even with the water surface. 6. Enable auto controls (they will turn green when enabled). Auto-Depth Auto-Heading 7. Begin operations and recording. Views Nav/Sonar/Video Video Sonar Nav Sonar/Video Thruster / Propeller Reference Propeller Identification Show/Hide Tabs LEFT The LEFT propeller has a black plastic base RIGHT The RIGHT propeller has a stainless band at its base Correct Propeller Type for each Location PORT VERTICAL STARBOARD LEFT RIGHT RIGHT Vertical (looking down on the vehicle from the rear) Horizontal (looking from behind the vehicle) 4 Hand Controller Input Identification NOTE: XBox Elite hand controller compatibility coming soon A B C K D F J M H I G E L N O P A. All Autos Off B. Open Manipulator Jaws C. Close Manipulator Jaws D. Rotate Manipulator Jaws E. Lights Intensity F. Camera Tilt Up G. Camera Tilt Down H. Focus In I. Focus Out J. Vehicle Horizontal Control K. Camera Snapshot L. Camera Record M. Vehicle Vertical Control N. Sonar Frequency Selection O. Increase Sonar Range P. Decrease Sonar Range 5 Recovering the System Post Dive Check List 1. Navigate the vehicle back to the deployment site. 2. Disable auto controls and stop recording. Auto-Depth Auto-Heading 3. Retrieve the ROV. NOTE: It is okay to lift it by the tether. 4. Close the Greensea EOD Workspace by clicking on the red X on the top right corner of the EOD Workspace window. 5. Press the ROV Mains Power Switch. ON 6. Turn off the Operator Control Console using the Power Switch. OFF 7. Disconnect the tether from the ROV. 8. Disconnect the tether from the OCC whip. 9. Replace the tether caps on all tether connections. 10. Visually inspect the system for damage that might have occurred during your operation. 11. Rinse the salt water from the system and soak the submersible for 30 minutes in fresh water. 12. Return all components to their storage cases after they have dried. Verify System Connectivity 13. Heading - The Compass Bar will turn green when connected. 29 14. Depth - The Depth Tracker will turn green when connected. 30 15. Sonar - Imagery will display in the sonar window when the sonar has connected. 31 16. Video - Imagery will appear in the video window when the camera has connected. 32 USBL Installation NOTE: The USBL is an optional accessory NOTE: If not using the USBL, make sure the ROV connector port is sealed 17. Remove the float block. 1 18. Feed the USBL accessory cable through the GPS hole in the float block. 19. Connect the accessory cable to the power / communications module port. 20. Replace the float block and secure the USBL beacon using the rear float block screw. 14 21. Connect the Topside GPS Antenna to one of the Accessory USB Ports on the OCC. 28 22. Connect the USBL Topside Station to the OCC by plugging it into the Auxiliary 12 V Port for power 27 and the Accessory USB Port for communications. 28 23. Deploy the USBL Topside Station in the water. The OCC 16 17 22 18 23 19 24 25 26A 20 26 21 26B 27 28 15 Greensea Software 33 29 31 30 32 Pro 5 Component Identification 2 14 14 3 5 14 11 6 3 4 1 1. Float part number 70779 2. USBL Beac1on --(optional) part number 70693 3. LED Lighting Module part number 70023 (QTY 2) 4. Rotating Manipulator part number 70824 5. HD Camera Module part number 70044 6. Multibeam 750D Sonar part number 71047 7. Vertical Thruster part number 70503 8. Port Thruster part number 70503 9. Starboard Thruster part number 70503 10. Pro 5 Power and Comms Module part number 71006 11. AHRS Module part number 70273 12. Ballast part number 71044 13. Serial Number Plate 14. Float Block Screw 15. Operator Control Console (OCC) part number 70218 16. High Definition Display 17. Display Brightness 18. Universal Power Plug 100-124 volts AC 19. OCC Power On|Off Switch 20. ROV Power Mains/Emergency Stop 21. Line Insulation Monitor 22. HDMI Ports 23. Auxiliary Ethernet Port 24. Controller USB Port 25. Keyboard USB Port 9 26. Tether Whip Connection 12 26A-26B. Tether Double Ended Connector 27. Auxiliary 12 Volts (5 amp max) 28. Accessory USB Ports 29. Compass Bar 30. Depth and Altitude Tracker 31. Sonar feed 32. Video feed 33. Record button 34. Strain relief bolt 35. Test strain relief 8 12 10 Bottom view 9 11 7 10 13 8 Top viewAdobe PDF Library 16.0.7 Adobe InDesign 17.2 (Windows)