Deaf Bonce Hannibal Series Mid-Range Speakers
Thank you for purchasing Deaf Bonce products. Our company is committed to creating extremely loud sound systems with no loss of quality.
To ensure proper use, please carefully read through this manual before using this product. It is especially important that you read and observe cautions in this manual. Please keep the manual in a safe and accessible place for future reference.
Safety Instructions
- Fasten the speakers properly when installing in the vehicle. If the component is disconnected during driving, it may cause serious damage to passengers or other vehicles.
- Before installing, store the product in its original packaging to avoid accidental damage.
- Be careful when installing or dismantling the speaker. Do not let the speaker drop to avoid damage to its moving parts.
- When working with tools, follow safety rules.
- Before installation, switch off the head unit and all other audio devices to avoid their damage.
- Ensure the speaker location does not hinder the proper operation of mechanical and electrical devices of the vehicle.
- Do not install components in places exposed to water, excessive humidity, high or low temperature, dust, or dirt. The product may be operated at +5 °C (41°F) to +40 °C (104°F). In case of moisture condensation, let the product dry.
- When performing plumbing, drilling, or cutting works on the car, ensure there are no wiring, brake lines, fuel pipes, or other structural elements under the work area. Follow safety rules and use protective glasses and gloves.
- When stretching speaker cables, ensure they do not contact sharp edges or moving mechanical devices. Make sure they are firmly fixed and protected over the entire length.
- The diameter of the speaker cables must be selected according to the length and applied power.
- Never run cables outside the car or near moving parts of the car, as this can lead to destruction of the insulating layer, short circuit, and fire.
- To protect cables, use rubber gaskets if the wire passes through a hole in a plate, or other similar materials if it lies close to parts exposed to heat.
CAUTION!!! High sound pressure can damage your health! Please use common sense when controlling volume!
Wiring Diagrams
Do not expose your amplifier to loads below the value predetermined by the manufacturer. Various examples of connection types are given below. Use these examples to determine the required load impedance of your connection.
Serial connection of the speakers
| Voice coil | Total impedance |
| 4 Ohm x 2 MR | 8 Ohm |
| 4 Ohm x 3 MR | 12 Ohm |
| 4 Ohm x 4 MR | 16 Ohm |
Parallel connection of the speakers
| Voice coil | Total impedance |
| 4 Ohm x 2 MR | 2 Ohm |
| 4 Ohm x 3 MR | 1.33 Ohm |
| 4 Ohm x 4 MR | 1 Ohm |
Mixed connection of the speakers
| Voice coil | Total impedance |
| 4 Ohm x 4 MR | 4 Ohm |
CAUTION!!! High sound pressure can damage your health! Please use common sense when controlling volume!
Selection of the diameter of speaker cables
Use the table below to select the desired diameter based on the length and power consumption.
| Power consumption (W) | Cable length (m) | Size A.W.G mm² |
| 25 000 | 0-1 | 5 16,8 |
| 20 000 | 1-2 | 8 8,37 |
| 15 000 | 2-3 | 10 5,26 |
| 10 000 | 3-4 | 14 2,08 |
| 8000 | 4-5 | |
| 6000 | 5-6 | |
| 4000 | 6-7 | |
| 2000 | 7-8 | |
| 1000 | ||
| 500 | ||
| 250 | ||
| 100 |
Filtering, Recommended Amplifier Settings
The correct choice of amplifier, its settings, filtering, and enclosure largely influence the lifespan of your audio system. Select an amplifier with a nominal power not exceeding the nominal power of the speakers. Proper coordination of the head unit (HU) with the amplifier will allow you to get a clean, undistorted signal applied to the component, preventing overheating and voice coil damage. Recommended settings of the amplifier and HU: HU volume should not exceed 80%. The amplifier sensitivity should be set to 50%.
The recommended filter settings:
- High pass filter HPF (cuts frequencies below the set frequency): 150-250 Hz (24 dB/Oct) or 250-350 Hz (12 dB/Oct).
- Low pass filter LPF (cuts frequencies above the set frequency): 8-10 kHz (12 dB/Oct).
Recommended amplifiers: MFA-2.80, MFA-2.120, MFA-2.220, MFA-2.320, MFA-2.420, MFA-2.520, MFA-4.80, MFA-4.120, MFA-4.180, MFA-4.220, MFA-4.320, MFA-5.1000.
Specifications
| Model | HM-6E | HM-8E | HM-6S | HM-6E+ | HM-8E+ |
| Size (Inch) | 6.5 | 8 | 6.5 | 6.5 | 8 |
| Surround material | Cloth | Cloth | Cloth | Cloth | Cloth |
| Cone material | Pressed paper | Pressed paper | Pressed paper | Pressed paper | Pressed paper |
| Frame material | Stamped Steel | Stamped Steel | Stamped Steel | Stamped Steel | Stamped Steel |
| Magnet type | Ferrite | Ferrite | Ferrite | Ferrite | Ferrite |
| Power RMS (W) | 80 | 80 | 100 | 70 | 85 |
| Power MAX (W) | 160 | 160 | 200 | 140 | 170 |
| Voice coil size (Inch) | 1 | 1 | 1 | 1 | 1 |
| Voice coil wire | CCAW | CCAW | CCAW | CCAW | CCAW |
| Frequency response (Hz) | 100 - 11 000 | 75 - 11 000 | 100 - 11 000 | 100 - 12 000 | 80 - 11 000 |
THIELE-SMALL PARAMETERS
| HM-6E | HM-8E | HM-6S | HM-6E+ | HM-8E+ | |
| Impedance (Ohm) | 4 | 4 | 4 | 4 | 4 |
| Spl (dB) | 90.9 | 91.8 | 92.5 | 92 | 95 |
| Fs (Hz) | 89 | 77.4 | 98 | 102 | 80.1 |
| Vas (L) | 12.62 | 25.87 | 10.2 | 9.01 | 24.13 |
| Qts | 0.91 | 0.96 | 0.71 | 1.26 | 1.01 |
| BL | 3.6 | 4.1 | 4.35 | 3.46 | 4.13 |
This specified sensitivity is not directly connected with the sound pressure created in the vehicle, and therefore should not be used as the sole indicator for comparison with other speakers.
Dimensions
HM-6E
Diagram showing dimensions for HM-6E speaker.
HM-8E
Diagram showing dimensions for HM-8E speaker.
HM-6S
Diagram showing dimensions for HM-6S speaker.
HM-6E+
Diagram showing dimensions for HM-6E+ speaker.
HM-8E+
Diagram showing dimensions for HM-8E+ speaker.
Connection of terminals
Diagram showing speaker terminal connections.
Installation
Diagram showing speaker installation process.
Box Contents
- Mid-range speaker - 2 pcs.
- Owner's manual - 1 pc.
- Warranty card - 1 pc.
Warranty Period, After-Sales Service and Service Life Information
Each Deaf Bonce product is warranted to be free from defects in materials and workmanship under normal use and service. The warranty period for the product is 12 (twelve) months from the date on which the product is transferred to the consumer. During the warranty period, defective parts will be repaired or replaced at the discretion of the manufacturer, provided there are grounds for doing so under the laws of the consumer's country. The defective product must be returned to the dealer from whom it was purchased, together with the duly filled out warranty certificate, complete with original packaging.
Deaf Bonce shall not be liable for any damage caused by transportation. Deaf Bonce shall not be liable for any expenses or lost profits arising out of or in connection with the use or inability to use the product or any other incidental or indirect costs, expenses, or damages incurred by the customer. The warranty is valid in accordance with the laws currently in force. For more information, please visit the Deaf Bonce website and refer to the warranty card.
The manufacturer reserves the right to change the design and specification of the product without prior notice.
The service life of the product is 12 (twelve) months from the date on which the product is transferred to the consumer. Exploitation (including, but not limited to use for intended or any other purpose, transportation, storage, modification/alteration/improvement/upgrade) of the product or any part thereof after the expiry of the service life is not permitted. At the end of its service life, the product must be disposed of.
Information on Disposal of Electrical and Electronic Equipment (For European Countries with Separate Waste Collection)
Items marked with a "crisscrossed wheeled bin" symbol ? are not allowed to be disposed of with regular household waste. These electrical and electronic products should be disposed of in special reception centers equipped for recycling such products and components. For information about the location of the nearest disposal/recycling spot and the rules for waste delivery, please contact your local municipal office. Recycling and proper disposal help protect the environment and prevent harmful effects on health.
Manufacturer: Ningbo Sound Solution I&E Trading Co., Ltd
Made in China
QR codes for HM-6E, HM-8E, HM-6S, HM-6E+, HM-8E+ are present.
Visit: https://alphard.audio
