FREUND Indoor Station Quick Installation Guide

1 Package Contents

The package includes the following items:

• Indoor Station
• Quick Installation Guide
• Wall-mount Bracket
• 10 pin Cable*1
• 4 pin Cable*1
• 2 pin Cable*1
• TA4*30mm Screw*2
• PM4*16mm Screw*2
• Screw fixing seat*2

2 Physical Specification

3 Product Appearance Description

1) Front Panel

The front panel features a display screen and several control buttons:

• Button 1: Management Center Key
• Button 2: Monitor key
• Button 3: Unlock Key
• Button 4: Return / Hang up key
• Button 5: Answer key
• Button 6: Microphone

[Visual Description: The front panel shows a screen with the FREUND logo above it. Below the screen are six circular buttons labeled 1 through 6, corresponding to the functions listed.]

2) Rear Panel

The rear panel contains various interfaces for power and connectivity:

• Port 1: DC Power interface (12V/1A input) ?
• Port 2: Ethernet interface (standard RJ45, 10/100M adaptive). CAT5 or CAT5E network cable recommended. ?
• Port 3: Industrial power interface. ?
• Port 4: 1 set of RS485 interface (for connecting card readers, sensors, etc.).
• Port 5: 8 sets of alarm input interfaces (for connecting switches, infrared sensors, door sensors, vibration sensors, etc.). ?
• Port 6: Speaker. ?

[Visual Description: The rear panel shows a layout of ports and connectors with numerical labels corresponding to the descriptions.]

3) External Device Connection Diagram

This diagram illustrates how to connect external devices such as a switch, door magnetic switch, infrared sensor, vibration sensor, and emergency key to the indoor station's input and WAN ports.

[Visual Description: A block diagram showing the Indoor Station connected to a Switch via WAN port and Input Port. Other devices like Door magnetic switch, Infrared sensor, Vibration sensor, and Emergency key are shown connecting to Input Ports.]

4 Installation Diagram (Two Models)

Wall Bracket Dimensions

[Visual Description: A diagram showing the dimensions of the wall bracket. Key dimensions include 102.00mm, 90.00mm, 28.00mm, 79.43mm, 60.00mm, 58.43mm, 4.00mm, 52.06mm, 4.00mm, 106.00mm.]

Desktop Bracket

A desktop bracket is available for purchase independently.

Model 1. Wall-mounted Installation

Step 1. Install Wall Bracket

Without 86 embedded box in the wall:

1. According to the position of the cable in the wall, dig out a square hole (height*width*depth=58.5*60*50mm) that can accommodate all cables.
2. Align the square hole of the wall bracket with the hole dug out, then mark the two fixation holes through the bracket on the wall.
3. Take down the bracket, use an electric drill to make the two fixation holes on the wall, then insert the two screw fixing seats provided.
4. Fix the wall bracket on the wall with two TA4*30mm screws.

[Visual Description: Steps A, B, C, D illustrate the wall mounting process. Step D shows a TA4*30mm Screw.]

With 86 embedded box in the wall:

1. Make sure all cables are in the embedded box.
2. Fix the wall bracket on the 86 embedded box with two PM4*16mm screws.

[Visual Description: An illustration shows fixing the wall bracket to an embedded box using PM4*16mm screws.]

Step 2. Connect Peripherals

If you need to connect other input and output devices, please connect them to the host through the cable.

Step 3. Power on the device

If it is working properly, align the slot on the rear side of the panel with the pin on the wall bracket and slide the host down to complete the installation.

[Visual Description: An illustration shows the indoor station being slid down onto the wall bracket.]

Model 2. Desktop Installation

Align the slot on the rear side of the panel with the pin on the desktop bracket and slide the bracket up to complete the installation.

5 Searching IP Address

There are two methods to search for the device. The default WAN mode is DHCP.

Method 1: Using iDoorPhone Network Scanner

Open the iDoorPhone Network Scanner, click the Refresh button to search the device and find the IP address.

Download address: http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe

[Visual Description: A screenshot of the iDoorPhone Network Scanner (V 1.0) interface showing IP Address, Serial Number, MAC Address, SW Version, and Description. A 'Refresh' button is visible.]

Method 2: Via Device Menu

After booting, navigate to "Menu" --- "Status".

6 IP Indoor Station Setting

Step 1: Log in the web setting page of Indoor Station

Input the indoor station's IP address (e.g., http://172.18.70.55) into the address bar of your PC's web browser.

The default username and password are both "admin".

[Visual Description: A screenshot of a login page with fields for User, Password, and Language selection, and a 'Logon' button.]

Step 2: Add the SIP account

Set the SIP server address, port, username, password, and SIP user with assigned SIP account parameters. Select "Activate", and then click "Apply" to save the setting.

[Visual Description: A screenshot of the web interface showing SIP settings, including server details, registration expiration, proxy settings, and activation options.]

Step 3: Feature Setting

Configure various features such as auto on hook, silent mode, auto hang-up delay, default line, and more.

[Visual Description: A screenshot of the web interface showing 'Features' settings, with options like 'Enable Auto on Hook', 'Enable Silent Mode', 'Auto HangUp Delay', etc.]

Step 4: Unlock Setting

Configure the Function Key settings. Set the unlock key type to "DTMF", and specify the value (password) to open the correct access control device.

[Visual Description: A screenshot of the 'Function Key' settings page, showing configurations for DSS Keys, including Type, Name, Value, Subtype, Line, and Media.]

7 Local Operation

Answer/hang up calls

When the door phone calls the indoor station, click the Answer key (Button 5) to answer the call, and click the Return / Hang up key (Button 4) to hang up the call.

Unlock the door

During the call of indoor station and door phone, click the Unlock Key (Button 3) to unlock the door.

Turn on/off the monitoring

Click the Monitor key (Button 2) on the indoor station to check the monitoring screen, and click the Monitor key (Button 2) to exit. (Only supports communication with video door phones).

Call management center

Click the Management Center Key (Button 1) on the indoor station to call the management center, and click the Return / Hang up key (Button 4) to cancel the call.