Signature Kitchen Suite (SKS)
Owner's Manual for SKS models including: SKSMD2401S, SKSMD2401S Microwave Oven Drawer, Microwave Oven Drawer, Oven Drawer
6 дней назад — The Easy Touch Automatic Drawer system eases open with a gentle pull or the touch of a button. ... For complete warranty details, refer to your Use & Care manual.
Signature Kitchen Suite 1.2 Cu. Ft. Stainless Steel Microwave Drawer | Vineland, NJ
File Info : application/pdf, 6 Pages, 1.14MB
DocumentDocumentSKSMD2401S MICROWAVE OVEN DRAWER Features Capacity Power Output Sensor Cooking Drawer Opening Lighting 1.2 cu. ft. 900 W Yes Easy Touch Automatic Incandescent Cooking Menu Display Type 1.2 CU. FT. OVEN CAPACITY 1.2 cu. ft. capacity is designed to provide plenty of room to heat large items like casserole dishes and dinner platters. EASY TOUCH AUTOMATIC DRAWER The Easy Touch Automatic Drawer system eases open with a gentle pull or the touch of a button. Give the drawer a small nudge and it smoothly shuts for you. The even, gliding action and solid construction prevents liquids from spilling during opening and closing. SMOOTHTOUCH® GLASS CONTROLS Intuitive SmoothTouch® Glass Controls not only look sleek but make operating the microwave drawer easy with just a touch. The seamless controls are also easy to wipe clean. INSTALLATION FLEXIBILITY Flexible installation options include below an island or peninsula and in standard cabinetry. A heat deflector kit is included for flush or true flush installation for an integrated, streamlined look. Power Levels Sensor Touch Cooking / Reheat Options Defrost Options Minute PlusTM Stop/Clear, Start/Enter Completion Beeper Energy Saving Mode Kitchen Timer/Clock Child Safety Lock SmoothTouch® Glass Touch 11 12 (Baked Potatoes, Sweet Potatoes, Fish / Seafood, Brown Rice, White Rice, Quick Fresh Vegetables, Longer Fresh Vegetables, Steamer Bag, Frozen Vegetables, Ground Meat, Frozen, Beverage Reheat 6 (Ground Meat, Steaks/Chops, Boneless Poultry, Bone-in Poultry, Roast, Casserole/ Soup) Yes Yes Yes Yes (Dims Display After 3 Minutes of Inactivity) Yes Yes ©2025 LG Electronics USA, Inc. All rights reserved. "Signature Kitchen Suite" and the Signature Kitchen Suite logo are registered trademarks of LG Electronics Inc. Design, features and specifications are subject to change without notice. Specifications are for planning purposes only. Consult the product's installation instructions for final dimensional data and other details prior to making cutouts or custom panels. Consult with a heating and ventilation engineer for your specific ventilation requirements. Non-metric weights and measurements are approximate. Smart features require Internet access. 1-855-790-6655 | www.signaturekitchensuite.com Page 1 of 6 | Effective 2/25 SKSMD2401S MICROWAVE OVEN DRAWER Installation Features Deflector Vent Kit Included (Required Yes for Flush and True Flush Installation) Technical Specs Required Power Supply Plug Type Power Cord Length (inches) 120V, 60Hz / 15 Amp 3-Prong 48 Dimensions and Weight Overall Exterior Width (inches) Overall Exterior Height (inches) Overall Exterior Depth (inches) Required Cutout Width (inches) Required Cutout Height (inches) Required Cutout Depth (inches) Interior Width (inches) Interior Height (inches) Interior Depth (inches) Net Weight (approx.) Shipping Weight (approx.) 23 7/8 15 15/16 23 1/64 22 1/8 15 9/16 23 1/2 17 5/16 7 1/8 16 9/16 74 lbs 88 lbs Warranty Summary* Limited Warranty, Parts & Labor (In Home Service) Limited Warranty on Magnetron (In Home Service) 3 Years 10 Years OVERALL PRODUCT DIMENSIONS 4 11/16" (119 mm) 1 3/4" (44 mm) 15 15/16" (405 mm) 21 5/8" (549 mm) 4" (102 mm) 15" (381 mm) Auto Drawer Opening 14 19/32" (371 mm) 23 7/8" (606 mm) 21 7/8" (556 mm) 1 5/16" (33 mm) Door Thickness MOUNTING SCREW LOCATIONS Mounting Flange *These warranties give you specific legal rights and you may have other rights that vary from state to state. For complete warranty details, refer to your Use & Care manual. Page 2 of 6 | Effective 2/25 SKSMD2401S MICROWAVE OVEN DRAWER STANDARD (PROUD) INSTALLATION Suggested electrical outlet location* 5" (127 mm) 6" (152 mm) Anti-Tip Block 3 1/2" (89 mm) C 22 1/8" 4" (101 mm) (562 mm) A B 23 1/2" (597 mm) A Minimum Depth 14 13/16" (376 mm) to Bottom of Anti-Tip Block 15 9/16" (395 mm) 36" (914 mm) Countertop Height D A - Allow 7/8" (22 mm) overlap B - Allow 3/16" (5 mm) overlap C - Allow 7/16" (11 mm) minimum space 24" (914 mm) Cabinet Minimum D - Allow 1/8" (3 mm) overlap *Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges. Notes The floor of the opening should be constructed of plywood strong enough to support the weight of the oven (about 100 pounds). Electrical A 120V, 60Hz grounded power receptacle should be installed at the back of the cabinet opening. Warning Be sure that the clearance of the floor between the wall oven and the microwave drawer is a minimum of 2-inches. Page 3 of 6 | Effective 2/25 SKSMD2401S MICROWAVE OVEN DRAWER A growing trend in the installation of kitchen appliances is mounting flush. This allows the consumer to present their appliances with a clean, flush with the cabinet face appearance. In this installation type, there are two ways to accomplish this look: 1/4" front extended and true flush. FLUSH (1/4" FRONT EXTENDED) INSTALLATION REQUIRES DEFLECTOR VENT (KIT INCLUDED) Suggested electrical outlet location* 24 3/16" (614 mm) Minimum 24 1/2" (622 mm) Maximum 1 1/16" (27 mm) 23 1/2" (597 mm) Minimum Depth 1 3/4" (44 mm) 4" (101 mm) 22 1/8" (562 mm) 5" (127 mm) 6" (152 mm) Anti-Tip Block 3 1/2" (89 mm) 14 13/16" (376 mm) to Bottom of Anti-Tip Block 16 15/16" (430 mm) Anti-Tip Block Mounting Note: the face of the cleat shelf must sit 1 3/4" (44.4 mm) back from the face of the cabinet. 22 1/8" Cabinet face Shelf face 1 3/4" Cabinet face (562 mm) Mounting cleat opening width Drawer face (44 mm) CL Top view Note: the mounting surface of the finished cleat must sit 1 1/16" (27 mm) back from the face of the cabinet (pushing *Can also be installed using an electrical outlet in an adjacent cabinet within the the face of the drawer out 1/4" (6 mm)) area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges. Notes In the flush 1/4" front extended application, the appliance can be mounted slightly "proud" of the cabinet cutout, which will create a flush appearance. Having the 1/4" extension also allows to hide the cabinet cutout edges. Page 4 of 6 | Effective 2/25 SKSMD2401S MICROWAVE OVEN DRAWER TRUE FLUSH INSTALLATION REQUIRES DEFLECTOR VENT (KIT INCLUDED) 16 7/8" (429 mm) Anti-Tip Block Mounting cleat 22 1/8" (562 mm) Mounting cleat opening width CL Top view Drawer face Cabinet face Note: The mounting surface of the finished cleat must sit 1 5/16" (33 mm) back from the face of the cabinet. *Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" (38 mm) diameter hole and deburred of all sharp edges. Notes In the true flush application, the appliance is mounted just as described, truly flush with the cabinet face. However, due to the appliance face and the cabinet face being on the same plane, the cabinet cutout edges will be visible and exposed. It is recommended in this true flush installation to finish / stain these edges. Page 5 of 6 | Effective 2/25 SKSMD2401S MICROWAVE OVEN DRAWER DEFLECTOR VENT KIT INSTALLATION REQUIRED FOR FLUSH AND TRUE FLUSH INSTALLATION Suggested Electrical Outlet Location Anti-Tip Block No Oven 22 1/8" (562 mm) Mounting Cleat Opening Width 24 3/16" (614 mm) Min 24 1/2" (622 mm) Max Flush Opening Width 16 15/16" (430 mm) Flush Opening Height Anti-Tip Block 3/4" (19 mm) Shelf 3/4" (19 mm) Shelf Front Face of Cabinet 1 3/4" (44 mm) Front Face of Shelf Front View Side View Shelf detail showing the deflector vent during installation. Position deflector vent and mark holes. Pre drill using a 1/16" (1.57 mm) bit before mounting. Shelf detail showing the deflector vent installed. Page 6 of 6 | Effective 2/25