Electric Microcrystallograph – SC632

Parts Name

1. Adjustment of speed and ON/OFF; 2. Adjustment of needle length; 3. Needle connect; 4. Needle cartridge

Diagram Description: A pink microcrystallograph device is shown with numbered callouts pointing to different parts. Callout 1 points to the main body of the device, indicating speed and ON/OFF adjustment. Callout 2 points to a rotating ring on the device, indicating needle length adjustment. Callout 3 points to the connection point for the needle cartridge. Callout 4 points to a small, cylindrical needle cartridge.

How to Operate

Usage method

1. Clean skin: Perform daily makeup removal and cleansing. Toner can be used for secondary cleaning.
2. Take out the nanowafer and install it on the top of the microcrystallizer.
3. Apply a proper amount of liquid or essence to your face.
4. Press the power switch key for 3 seconds to start the microcrystallograph. Contact the skin vertically. Each contact point is recommended to stay for 35 seconds.
5. After the operation, turn off the power supply and remove the nano chip. Apply common skin care products and recommend the use of essence. A sterile repair mask can be applied before applying skin care products.
6. Nano chips cannot be used repeatedly to avoid cross-contamination.

Instrument operation

1. Long press to start/shut down. The default first blue light is on. Click the button to switch gears cyclically after starting: the second green light is on, and the third red light is on.
2. Charging display: Red light indicates charging; green light indicates full charge.

How to Operate

Preparation

1. Take out the needle cartridge from its sterilized packaging.
2. Fit round slots 1 into 2 of the machine, and push the needle cartridge horizontally up to the end.
3. Lock the cartridge by turning it counter-clockwise.
4. Adjustment of needle length should be done after turning on the machine.
5. To remove the needle cartridge, turn it clockwise and push it out horizontally, aligning the fitting round slots (slot 1 and slot 2) together.

Adjustment of needle length

The needle length can be adjusted by turning the adjustment ring clockwise or counter-clockwise. Turning it clockwise makes the needle longer. Turning it counter-clockwise makes the needle shorter.

Diagram Description: Two illustrations of the needle cartridge. The first shows a needle cartridge with a ring labeled '1'. The second shows the same cartridge with a ring labeled '2'. The text indicates that turning the ring clockwise (labeled '2') makes the needle longer, and counter-clockwise (labeled '1') makes it shorter.

Manipulation techniques

Point method

When the microcrystallograph is installed, the nanowafers are vertically touched on the skin surface, creating a slight depression visible visually, with a gentle and dense upper and lower edge. Adjust the strength according to the contact position.

Sliding method

When the microcrystallograph is installed, the microcrystalline wafer is vertically touched on the skin surface, and a slight quadruple-pit sensation can be observed visually. While sliding in a straight line, the nanowafer does not leave the skin surface. It is recommended to stay at the same part for 3-5 seconds and no more than 2 times.

Circle method

When the microcrystallograph is installed, the nano-wafer is perpendicular to the skin surface. It can visually detect the sense of retraction. The nano-wafer is circled at a uniform speed and does not leave the skin surface. It is recommended that the nano-wafer stay at the same place for 3-5 seconds and no more than 2 times.

Matters needing attention

Notes for nano-electric microcrystallograph:

1. Do not disassemble or refit chargers and microcrystals. It is strictly forbidden to use chargers when the power supply is damaged. Otherwise, it will lead to electric shock, fire, and charger damage.
2. It is strictly forbidden to contact the charger with wet hands. If the charger touches other liquids, water, or fire, cut off the power supply immediately.
3. Do not short-circuit the charger. Do not use it with mechanical vibration or shaking. Avoid direct sunlight, bathrooms, and other high-temperature places. The equipment is not waterproof and should not be exposed to rain or dampness.
4. Do not use chargers near TV, radio, or other electrical appliances.
5. Pay attention to the charger when plugging in and pulling the power cord, as this can damage the wire. When charging, the microcrystallizer and charger must be placed in a ventilated place with a temperature between -10°C and +55°C. Using an unauthorized charger can cause danger and violate the manufacturer's warranty terms.
6. Keep the charger out of the reach of children to avoid danger.

Notes for nanowafers:

1. If the disposable packaging is incomplete or leaky, do not use it to avoid skin contamination.
2. Before operation, ensure the operating parts and hands are clean.
3. For the first time, it is recommended to perform a skin test with skincare products on the inside of the wrist. Do not use if itching or other allergic phenomena occur.
4. Apply moderate force when using the wafer; do not press intentionally or lift the wrist until the wafer can no longer touch the skin.
5. About 10-20 minutes after using nano-wafers, some people may experience skin redness, which is a normal phenomenon and will disappear within 24 hours without treatment.
6. Except for the wafer head, do not allow contact with water or other liquids on other parts of the instrument to avoid damaging the machine.
7. The same wafer can only be used by one person for one time. It is strictly forbidden to share one wafer with others. It is forbidden to use the same wafer multiple times after disinfection. Otherwise, it may cause skin allergies, redness, spots, inflammation, and other adverse consequences.
8. When preserving nanowafers, discard used wafers and store unopened wafers and microcrystallographs in a well-ventilated environment, avoiding dampness, heavy pressure, and shock. Keep them away from children.
9. In the process of use, the nano-wafer should move continuously and stay at the same part for 3-5 seconds, no more than 2 times.

Suggestions for the Use of Problematic Skin Dry and sensitive skin:

Before using any efficacy products, apply three imported products (e.g., hyaluronic acid replenishment mask). After the skin does not need water, then apply the effective products. Before introducing effective products, perform a small-scale introduction. If the skin is not red, swollen, itchy, or shows other symptoms, then proceed with application on the face.

Please use wash-free repairing and rehydrating products in time after application.

Suggestions for skin with spot problems:

Use freckle essence combined with replenishment products, such as whitening and freckle essence.

Skin with acne problems:

It can be imported with acne products. If the acne skin itself has inflammation, it is recommended not to apply to the entire face back and forth when importing; only apply to the area with acne to avoid infecting other parts of the face.

Print Import Note: It can be imported with acne-removing products and freeze-dried powder. First, use freeze-dried powder to import the pockmarks. When importing, avoid infection by bypassing the operation of the pockmarks. Finally, introduce the anti-acne products vertically onto the pockmarks.

Specific manipulation of acne pit:

After cleaning the face, first use the instrument to point on the pit, then apply freeze-dried powder on the pit, and then use the instrument to point until the pit is red or slightly painful. Twice a week, daily morning and evening, smear frozen thousand powder. Generally, continue to use for more than three months for more obvious effects.