MAGMATIC SIDEWINDER

Important Warnings

WARNING! BURN HAZARD: The front nozzle reaches high temperatures. Do not touch even after turning off.

(Also noted in German: Verbrennungsgefahr. Also noted in French: Risque de brûlure. Also noted in Spanish: Peligro de quemaduras.)

Document Version

Due to additional product features and/or enhancements, an updated version of this document may be available online. Please check www.elationlighting.com for the latest revision/update of this manual before beginning installation and/or programming.

General Information

Introduction

Please read and understand the instructions in this manual carefully and thoroughly before attempting to operate this device. These instructions contain important safety and use information. This product is intended to be used by professionally trained personnel only and is not suitable for private use.

Unpacking

Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton is damaged, carefully inspect the device for damage, and be sure all accessories necessary to install and operate the device have arrived intact. In the event that damage has been found or parts are missing, please contact customer support for further instructions. Do not return this device to your dealer without first contacting customer support. Do not discard the shipping carton. Please recycle whenever possible.

Box Contents

• Twist-locking power cable (x1)

Customer Support

Contact MAGMATIC customer service for any product-related service and support needs. Also visit forums.elationlighting.com with questions, comments, or suggestions.

ELATION SERVICE USA - Monday - Friday 8:00 AM to 4:30 PM PST
323-582-3322 | Fax 323-832-9142 | sales@magmaticeffects.com

ELATION SERVICE EUROPE - Monday - Friday 08:30 to 17:00 CET
Voice: +31 45 546 85 63 | Fax: +31 45 546 85 96 | support@elationlighting.eu

REPLACEMENT PARTS: Please visit parts.elationlighting.com

Important Notice!

There are no user-serviceable parts inside this unit. Do not attempt any repairs yourself. Doing so will void your manufacturer's warranty. Damages resulting from modifications to this fixture and/or the disregard of safety instructions and guidelines in this manual void the manufacturer's warranty and are not subject to any warranty claims and/or repairs.

Never point or aim a fog machine towards people or their clothing. This unit emits hot vapor and should be used with the same care that you would observe when using an electric kettle or iron.

Limited Warranty (USA Only)

A. Magmatic Effects warrants products to be free of manufacturing defects in material and workmanship for a period of two years (730 days) from the original date of purchase. This warranty excludes discharge lamps and all product accessories. This warranty is valid only if the product is purchased within the United States of America. The owner must establish the date and place of purchase by acceptable evidence when service is sought.

B. For warranty service, send the product only to the Magmatic Effects factory. All shipping charges must be pre-paid. Magmatic Effects will pay return shipping charges to a designated point within the United States if repairs are covered. Ship the product in its original package and packaging material. Do not ship accessories. Magmatic Effects shall have no liability for loss or damage to any shipped accessories.

C. This warranty is void if the product serial number/labels are altered or removed; if the product is modified in a manner affecting reliability; if repaired or serviced by anyone other than the Magmatic Effects factory without prior written authorization; or if damaged due to improper maintenance.

D. This is not a service contract and does not include maintenance, cleaning, or periodic check-ups. Magmatic Effects will replace defective parts at its expense and absorb warranty service and repair labor costs for defects in material or workmanship. The sole responsibility of Magmatic Effects is limited to repair or replacement of the product, including parts, at their discretion. Products covered by this warranty were manufactured after January 1, 1990.

E. Magmatic Effects reserves the right to make design and performance improvements without obligation to include these changes in previously manufactured products.

F. No warranty, expressed or implied, is given for accessories. Implied warranties of merchantability or fitness are limited to the warranty periods set forth above. Magmatic Effects shall not be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.

G. This warranty is the only written warranty applicable to Magmatic Effects products and supersedes all prior warranties and descriptions.

Warranty Returns (USA Only)

To obtain warranty service, a Return Material Authorization (RMA) number must first be obtained from MAGMATIC. The customer must provide product proof of purchase and serial number (e.g., invoice copy, Extended Warranty Certificate) and relevant maintenance records. Failure to provide acceptable evidence may result in denial of service.

Products returned for warranty service must be sent without accessories (power, data, safety cables, brackets, clamps, rigging hardware, frost filters, gel frames, barn doors, lenses, hoses, nozzles, rack mounting hardware, etc.). They must be boxed using original or suitable packaging materials (double-box and foam) for adequate protection during transit. Shipments must be freight pre-paid and insured to MAGMATIC in Los Angeles, CA, or a MAGMATIC Authorized Service Center. The RMA number must be clearly written on the outside of the return box, and a brief description of the problem and the RMA number must be included in the box.

Products returned without an RMA number clearly marked on the package will be refused and returned to the shipper at the customer's expense. Products returned damaged due to inadequate packaging or shipping carrier damage may incur additional repair charges and/or void the warranty. MAGMATIC and/or the Authorized Service Center shall have no liability for loss or damage to any accessories shipped with the product. If requested repairs are within the warranty terms, MAGMATIC will pay return ground transportation shipping charges to a single designated point within the United States.

Safety Guidelines

This fixture is a sophisticated piece of electronic equipment. Follow all instructions and guidelines in this manual for smooth operation. Magmatic Effects is not responsible for injury or damages resulting from misuse due to disregard of this manual's information. Only qualified/certified personnel should perform installation using only the original rigging parts. Modifications to the fixture or mounting hardware void the manufacturer's warranty and increase the risk of damage or personal injury.

⚠️ PROTECTION CLASS 1 - FIXTURE MUST BE PROPERLY GROUNDED.

⚠️ IMPORTANT:

• There are no user-serviceable parts inside. Do not attempt repairs yourself; this voids the warranty.
• Do not plug this unit into a dimmer pack.
• Do not remove the cover under any conditions.
• Keep unit in an upright position.
• Never operate this unit with the cover removed.
• Unplug from power during long periods of non-use.
• Ensure tank is empty before storage or transport.
• Do not move when filled with fluid.
• Disconnect power before adding fluid or performing maintenance.

FOR USE IN INDOOR / DRY LOCATIONS ONLY

• Do not expose device to rain and/or moisture. ?❌ [Keep Dry]
• Place unit in a well-ventilated area.
• Allow 40" (100cm) above and around the unit for proper ventilation.

Safety Guidelines (Continued)

CAUTION: Fog machines may set off smoke alarms!

• Do not attempt installation or operation without proper knowledge.
• Do not point or direct fog output in an unsafe direction.
• Do not touch the front nozzle during or immediately after operation, as it may be hot.
• Do not shake the device; avoid brute force during installation or operation.
• Save the packing carton in case the device needs to be returned for service.
• Do not spill water or other liquids into or on the device. Ensure fog fluid is kept inside the reservoir.
• Ensure the local power outlet matches the required voltage for the device.
• Do not remove components or disassemble the device; there are no user-serviceable parts inside.
• Never connect this device to a dimmer pack.
• Do not attempt to operate if the device has been damaged.
• Never use this device with the cover removed.
• To reduce risk of electrical shock or fire, do not expose this device to rain or moisture.
• Do not operate if the power cord is frayed, crimped, or damaged. Replace damaged cords with new ones of the same power rating.
• Do not remove or break off the ground prong from the electrical cord; it reduces the risk of electrical shock and fire in case of an internal short.
• Always disconnect from main power before making any connection, performing cleaning or maintenance, or adding or draining fluid.
• Always drain fluid before moving the device.
• Always mount this device in an area that allows proper ventilation.
• Always disconnect power cords during long periods of non-use.
• This unit is intended for indoor use only. Outdoor use voids all warranties.
• Always mount this unit in a safe and stable manner.
• Route power cords out of the way of foot traffic to avoid being walked on or pinched.

The device should be serviced by qualified service personnel when:

• The power cords or plugs have become damaged.
• Objects have fallen on and/or liquid has spilled into the device.
• The device has been exposed to rain and/or moisture.
• The device does not operate normally or exhibits a marked change in performance.

Overview

Diagram showing the front and side views of the MAGMATIC SIDEWINDER fog machine with numbered callouts.

• 1. Power In
• 2. Breaker
• 3. DMX In
• 4. DMX Out
• 5. Wired Remote Port
• 6. Touch Display Screen
• 7. Safety Cable Attachment
• 8. Carry Handles (x2)
• 9. LED Array
• 10. Fog Outlet
• 11. Mounting Clamp Points (x4)
• 12. Tank Level Gauge
• 13. Latch Screw
• 14. Tank Access Panel

Operation

• When first unboxing, open the shipping carton and carefully remove the device. Remove all packing material, paying particular attention to the area around the fog outlet vent.
• Always set up the device on a flat dry surface.
• Make sure the unit is disconnected from power before adding fluid to the tank.
• To access the fluid tank, unscrew the latch screw on the back side of the unit, near the fluid notice, then open the access panel.
• To fill the tank, remove it from behind the access panel. Unscrew the tank cap and fill with MAGMATIC ATMOSITY fluid (SKU# AFF only), then replace the cap.
• Never run the device on anything other than approved, MAGMATIC branded fluid, as doing so can result in severe damage.
• When placing the tank back, be careful not to pinch, twist, or tangle the feed tube connected to the tank cap.
• To close and secure the tank access panel, tighten the latch screw by pushing it down while rotating.
• After re-connecting the device to power and switching it on, allow the fluid to warm up for at least nine (9) minutes before beginning fog emission.

PLEASE NOTE: While the fog duration setting can be set as high as 250 seconds, individual bursts of continuous fog output will only occur for a maximum of 8 seconds. The device will produce a series of shorter fog bursts, each lasting up to 8 seconds, throughout the set duration.

Control Panel

This fixture includes a system menu with an easy-to-navigate touch screen control panel for settings and adjustments. When first powering on, the main menu is displayed.

Press the main menu icon you wish to access. Use the ENTER button to access sub menus and the UP and DOWN buttons to make adjustments. Press ENTER to confirm adjustments. Exit the main menu at any time without making adjustments by pressing the BACK/EXIT button.

Main Menu Screen

[DMX Set Icon] [Personality Icon] [Manual Icon]
[Preset Icon] [Information Icon] [Timer Icon]

Navigation Icons

[Back/Exit Icon] [Up Arrow Icon] [Down Arrow Icon] [Enter Icon]

Timer Icons (Timer Menu)

[Back/Exit Icon] [Settings Icon] [Play/Start Icon]

System Menu

DMX Set

WiFi Set

PERSONALITY

MANUAL

TIMER

Start or pause device operation according to these values by pressing the Play/Start icon.

PRESET

PRESET (Continued)

INFORMATION

DMX Channel Functions & Values

Macro Table

Dimensional Drawings

Diagrams showing the dimensions of the Magmatic Sidewinder fog machine. Dimensions may not be drawn to scale.

Side View: Height: 16.26 in. (413 mm)

Top View: Width: 14.80 in. (376 mm)

Front View: Depth: 7.60 in. (193 mm)

Trouble Shooting

If you experience low output, pump noise, or no output at all, disconnect the device and discontinue use immediately. Do not attempt to continue operation as this may damage the machine. Check the fluid level, the breaker, and the wall outlet to make sure that it is sending power. If all the above factors do not appear to be causing the issue, and the unit still fails to operate correctly, the unit will require service. Please contact Magmatic Effects for assistance.

Cleaning & Maintenance

When storing your device, be sure to store it in a cool area. Cover the device so that dust does not build up. When storing for long periods, it is highly advisable to run the device at least once every 3-4 months. Long periods of inactivity can severely shorten the life of your device.

Only run Magmatic's Atmosity fluid (SKU# AFF) through your machine. Never run plain water, vinegar, or any other liquid solution through your device, as doing so will severely damage your device.

Specifications

Performance

• Rated Power: 1450W
• Max Output: 50,000 CFM* (cu ft/min.)
• Max Continuous Output: 8 Seconds @ Full
• Max Throw Distance: 25 Feet
• Initial Ready Time: 9 Minutes
• Cycling Ready Time: 1 Minute
• Fluid Capacity: 2.5L
• Fluid Consumption: 180ml/min.

Compatible Fluid

• Atmosity Flash Fog Fluid (AFF-4L)
• Atmosity Extreme Filtered Fog Fluid (AEF-4L)

Construction

• Thermally Protected Heat Exchanger
• Advanced HPA (high pressure air) Pump Technology Energy Saving Mode with Auto-Clean Process
• Sealed Fluid Reservoir
• External Visual Fluid Level Detection
• Compact Light Weight Mobile Design

Control

• 3 DMX Channel Modes (1 / 4 / 7)
• Onboard LCD Touch Control Panel
• DMX-512 and RDM Protocol Support
• Optional MagFLY Wireless DMX Transceiver
• Optional MagRF and Wired Remotes

Connections

• 5-pin locking XLR, In/Out Data Connectors
• IP65 Locking Input Power Connector
• With Wired Digital Communication Network

Size / Weight

• Length: 16.26 in. (413mm)
• Width: 7.60 in. (193mm)
• Height: 14.80 in. (376mm)
• Weight: 29.5 lbs. (13.4kg)

Electrical

• Input Voltage: 120V, 230V, 240V 50/60Hz
• 9A (NFB) Resettable Breaker
• Max Power Consumption: 1560W

Thermal

• Maximum Ambient Temperature (Ta max) 104°F (40°C)
• Exterior Surface Temperature, Steady State: 140°F (60°C)

Approvals / Ratings

• CE | cETLus (pending) | IP20

Specifications are subject to change without notice.