User Manual for deako models including: DS2002, 2AK29-DS2002, 2AK29DS2002, Smart Plug Include Floor Lamps and String Lights
Deako Inc. DS2002 Smart Plug 2AK29-DS2002 2AK29DS2002 ds2002
Smart Plug User Manual 1. Features Snowflake is a UL or ETL-listed, Smart Plug for the US and Canadian market. Model:DS2002 · Loads: o Resistive 15A o Incandescent/Halogen 1000W o Motor ½ HP · User Interface o Indicator LED o On/Off button Figure 1 - Smart Plug Design Page 1 Status LED Figure 2 - Front View Button Figure 3 - Button View 2. Snowflake ElectronicInterface Requirements The electronics in Snowflake includes an AC/DC converter, the ESP32 Module, a relay and the user interface hardware (two buttons and one LED). The Supplier is responsible for all HW design and development and Deako is responsible for firmware development. A high-level block diagram is shown in Figure 4. Page 2 LED0 On/Off Pair ESP32 Module Figure 4 Snowflake Electronics Block Diagram The ESP32 WROOM32 Module will sit on a daughter card that interfaces to the main smart plug board. The daughter card will bring out at least 10 connections from the ESP32 WROOM32 Module to the smart plug PCB. 3. Snowflake Specifications Deako expects the Supplier to create a test plan that demonstrates compliance to these specifications Table 1 - Snowflake Specifications # 3.1 Operating temperature 3.2 UI surface temperature, max resistive load, max temperature after equilibrium 3.3 Maximum Load Incandescent/Halogen 3.4 Maximum Load ELV/LED Maximum Load MLV 3.5 3.6 Load Motor 3.7 Load General Purpose 3.8 Load Resistive 3.9 UL/ETL 3.10 UI 3.11 Radio 3.12 Power Consumption with Load in Off State 3.13 Neutral Required Spec 0°C - 40°C <50°C 1000W Supplier to provide spec Supplier to provide spec ½ HP Supplier to provide spec 15A Yes 2 Buttons + 1 LED Combo 500mW Yes Page 3 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user's authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, (2) This device must accept any interence received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Page 4 IC Statement - English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licenceexempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. -French: L'émetteur/récepteurexempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et DéveloppementéconomiqueCanada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: -(1) l'appareil ne doit pas produire de brouillage, et -(2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. l'appareil numérique du ciem conforme canadien peut - 3 (b) / nmb - 3 (b). cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs rf et la conformité. L'appareil a été évalué pour répondre aux exigences générales d'exposition aux radiofréquences. L'appareil peut être utilisé en condition d'exposition portable sans restriction. This device complies with ISED RF radiation exposure limits set forth for an uncontrolled environment. This device must be installed and operated with a minimum distance of 20 cm between the radiator and user body. Le présent appareil doit être installé et exploité à une distance minimale de 20 cm entre le radiateur et les corps. Page 5Microsoft Word 2016