OrcaTorch Dive Lights - Lighting Solutions Provider for Safe Diving！
User Manual for ORCATORCH models including: SD03 Dive Beacon Torch, SD03, Dive Beacon Torch, Beacon Torch, Torch
File Info : application/pdf, 1 Pages, 434.58KB
DocumentDocumentFrontside Backside
User Manual
SD03
4-Colour Dive Beacon
PRODUCT INT ODUCTION
The OrcaTorch SD03 is a compact and multifunctional 4-colour dive beacon. It can emit light in 4 different colours and has 8 lighting modes: for each colour either constant light or flashing mode. Both colour and light mode can be chosen by rotating the body. The SD03 can be used as an underwater or outdoor signal light, dive backup light, outdoor regular light, etc. Its shell is made of plastic which provides good light penetration. With excellent waterproofness, it will function up to 150m underwater. There is no doubt that the SD03 is one of the best choices for diving or outdoor lighting.
PRODUCT FEATURES 4 single colours and 8Rmodes integrated in one light Compatible with 1*AA battery or 1*14500 battery Non-slip and comfortable silicone ring The tail D-ring can be used more easily with lanyard Practical and convenient mode memory function Plastic transparent shell with enhanced light guide performance
Professional waterproof design, depth rated to 150 meters underwater Reverse polarity protection, to protect the light from improper battery installation Aircraft-grade high-strength aluminum AL-6061-T6 used with type III military grade hard anodization technology
INSIDE THE BOX
ANSI/ NEMAFL1
Output
Runtime
BatteryType 14500 AA 14500 AA
White 100 lm White Flash 100 lm
50 lm 50 lm
3Hr 30mins
6Hr 30mins
3Hr 10mins
5Hr 30mins
Red
1 lm 0.5 lm 62Hr 95Hr
Red Flash 1 lm 0.5 lm 120Hr 250Hr
SD03x1, AA batteryx1, Lanyardx1, User Manualx1.
Note: The 14500 battery is not included in the box. If you need the 14500 battery, please buy it yourself.
Blue
1 lm
Blue Flash 1 lm
Green
1 lm
Green Flash 1 lm
0.5 lm 62Hr 0.5 lm 120Hr 0.5 lm 62Hr 0.5 lm 120Hr
120Hr 220Hr 120Hr 220Hr
SPECIFICATIONS
Notice: Stated data has been measured according to the international flashlight test standards ANSI/NEMA FL1 using one OrcaTorch 14500 Li-ion battery (3.7V, 900mAh) or 1*AA battery (1.5V, 1800mAh) under laboratory conditions. The parameters are approximate and may vary between flashlights, batteries and environments.
Max Intensity
14500 AA
280cd 600cd
Beam Distance
14500 AA
48m 33m
Waterproof
Underwater 150m
Impact Resistant
1.5m
Dimension
30.5mm (Head Dia)*76.15mm (Length) 1.2in (Head Dia)*3in (Length)
Net Weight
50g/1.76oz(excluding battery)
PRODUCT PICTURE
White LED AA Battery
Integrated shell
Silicone ring O rings
Red, Blue and Green Signal Lights
Lanyard
BATTERY INSTALLATION
The battery assembly direction is shown in the figure.
Note: The supplied AA battery is not rechargeable. If you need a rechargeable lithium 14500 battery, please buy it yourself.
OPERATION INSTRUCTION
ON/OFF Insert the battery and tighten the tail to turn on the SD03.
Mode Selection After the light is switched on, loosen and tighten the tail to switch modes among white, white flash, red, red flash, blue, blue flash, green, and green flash in sequence.
MEMORY FUNCTION The mode will be memorized if it has worked for more than 3S. The light will start from this mode by default when turned on the next time.
USAGE AND MAINTENANCE
Please clean the surface of the light with fresh water and wipe it dry afteruse in case of the seawater corrosiveness.
Do not drop or place the light on sand in case iron sand stick or go into switch section or screw thread.
Tighten all the connections of the light before going underwater.
Please take out the batteries after each diving.
Please don't disassemble the sealed head, doing so may cause damageto the flashlight and will void the warranty.
We recommend the use of high quality batteries. lf the flashlight will notbe used for a long time,remove the batteries to avoid damage fromelectrolyte leakage or
battery explosion. Please replace the O-rings if they are
damaged after prolonged use and regularly lubricate the o-rings so as to not erode the rubber. Doing so willkeep the flashlight properly sealed against water. Please clean the contacts of your light from time to time, especially when the light flickers or doesn't light up. There are probably several reasons for a flickering or not working light:
Reason A: The batteries need to be replaced. Solution: Replace batteries (Please confirm correct installation of + and -terminals). Reason B:The threads,PCB board contact or other contacts are dirty.Solution: Clean the contact points with an alcohol soaked cotton swab. lf the methods above don't work, please contact the distributors and referto the warranty policy.
USAGE AND MAINTENANCE
We will replace products afflicted with manufacturing defects within 30days of purchase and repair a light free of charge within 12 months ofpurchase if problems develop under normal use; if repair is required after12 months from the date of purchase, we will charge for parts.The totalrepair fee is dictated by the cost of the replaced materials.
Please register your OrcaTorch products through official website www.orcatorch.com to get extra 1 year warranty.
warning The flashlight is high intensity lighting device and capable of causingeye damage, please avoid shining the light directly into the eyes.
ORCATORCH TECHNOLOGY LIMITED
Tel:+86-755-33560383
Fax:+86-755-29454989
Email: info@orcatorch.com
www.orcatorch.com
Address: 7F, Building 6, Rundongsheng Industrial Park,
Gushu, Xixiang, Baoan, Shenzhen, China (518102)
SD03
OrcaTorch SD03 48 SD03 IP68150m SD03
48 150 AA 14500 D AL-6061-T6
SD03x1, AA x1, x1, x1 1450014500
ANSI/NEMA FL1, AA (1.5V1800mAh) 14500 (3.7V 900mAh)
ANSI/ NEMAFL1
14500 AA 14500
100 50 100 50
3 30 6 30
1 0.5 62
AA 3 10 5 30 95
1 0.5 120 250
1 0.5 62 120 1 0.5 120 220 1 0.5 62 120 1 0.5 120 220
14500 AA
280 600
14500
48
AA
33
IP68150
1.5
30.5()*76.15 () *10(
50()
AA
AA 14500
"-------"
3
O O
O
PCB /
ORCATORCH
www.orcatorch.cn 1
3030 11 1 ORCATORCH