atomi smart AT1824 Smart WiFi Ceiling Fan Owner's Manual

Owner's Manual for atomi smart models including: AT1824 Smart WiFi Ceiling Fan, AT1824, Smart WiFi Ceiling Fan, Ceiling Fan, Fan

Let's get started!

Smart WiFi Ceiling Fan - Syndigo

13 mar 2022 — WARNING. 1. To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure.

[PDF] Smart WiFi Ceiling Fan - Syndigo

Do not attempt to recharge non-rechargeable batteries. Remove exhausted ... Pause your fan to attach the clip to the end of any blade. Run your fan and ...

File Info : application/pdf, 15 Pages, 3.83MB

original

Let's get started!
Smart WiFi Ceiling Fan
Quick Start Guide
v1.12/21

FOR YOUR SAFETY

READ AND SAVE ALL INSTRUCTIONS BEFORE USING.

WARNING

1. To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure

and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the screws

provided in the bags C1, C2 or C3, or use the ones provided with the outlet box.

2. To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by

turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot

lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag,

to the service panel.

3. To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.

4. To reduce the risk of personal injury, do not bend the blades when installing or cleaning the fan. Do not

insert foreign objects in between rotating fan blades.

5. Chemical burn hazard. Keep batteries away from children. If a new or used battery is swallowed or

enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours.

Always completely secure the battery compartment. If the battery compartment does not close

securely, stop using the product, remove the batteries, and keep it away from children. If you think

batteries might have been swallowed or placed inside any part of the body, seek immediate medical

attention. Dispose of cells properly and keep away from children. Even used cells may cause injury.

6. Do not attempt to recharge non-rechargeable batteries. Remove exhausted batteries from the

product.

7. All wiring must be in accordance with national and local electrical codes. It is highly recommended

that you use a qualified electrician.

Caution: modifications not approved by the party responsible for compliance could void user's authority to operate the equipment.

Mounting to high ceilings?
Maximize your comfort by choosing the right accessory downrod length for your ceiling.
If you have an angled ceiling, you may need a longer downrod.

Visit www.atomismart.com to find additional downrod options.

WHAT'S IN THE BOX

Ceiling fan (x1)

Fan blade (x3)

12" downrod (x1) Angled canopy (x1) Glass shade (x1)

Light ring (x1)

LED board (x1)

Bag A Blade screw (x10) Paper washer (x11)

Bag B1 Standard mounting bracket (x1)

Bag B2 Angled mounting bracket (x1)

Bag C1 Short mounting screw (x4)
Washer (x4) Anchor (x4)

Bag C2 Long mounting screw (x4)
Washer (x4) Anchor (x4)

Bag C3 Concrete anchor (x2)

Bag D Wire nut (x3)

Brightness

Warm

On/O

Cool

Brightness

Speed

On/O

4H
Timer

Speed

Bag E1 Remote control (x1) Remote control mount (x1)

Bag E2 Remote control mount screw (x2) Remote control mount anchor (x2)

TOOLS NEEDED FOR INSTALLATION

Ladder

Screwdriver

Wire strippers (If applicable)

Drill (If mounting to a support structure or concrete. Only concrete-compatible
screws are included.)

SELECT YOUR INSTALLATION LOCATION
Measure room dimensions

CEILING FAN MOUNTING OPTIONS
Unpack and inspect the fan carefully to be certain all parts are included.

Flush Mounting
Pre-assembled. The Atomi Smart Ceiling Fan comes already prepped for this installation option.
Ceiling Outlet Box

Standard Mounting
Ceiling Outlet Box

30 inches

from blade tip

to nearest wall

or obstruction

7 feet from bottom edge of blade to the floor

Check the outlet box

The fan must be secured to the building structure or a fan-rated outlet box capable of supporting 32kg (70Lbs).

Standard bracket

maximum angle =

15 degrees

Ceiling Outlet Box
12" Downrod (minimum)

Angled Mounting

Angled bracket maximum angle =
35 degrees

FOR THIS STEP YOU WILL NEED

BAG
A

INSTALLING THE BLADES
One at a time, insert each blade into the slot on the fan structure. Secure each blade with the screws and washers found in bag A.

FOR THIS STEP YOU WILL NEED

ASSEMBLING THE LIGHT FIXTURE
1
Remove the three screws as shown in the drawing.

For seamless installation, insert and tighten side screws first (1).
Next, insert and tighten middle screw (2).

2
Pass the connector through the center hole of the light ring and
the LED board.

3
Connect the white plug from the housing structure to the white plug in the LED board.
4
Align the keyhole slots in the light ring and the LED board with the keyhole slots in the housing area. Insert the screws and tighten them.
8

INSTALLING THE BRACKETS
Only use the provided Atomi Smart ceiling bracket that comes with your fan. Pick which installation option (below) that works best for your location. Remove any existing bracket from your ceiling prior to installation.

PREVENT POSSIBLE ELECTRIC SHOCK. Before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.
WARNING
Secure the bracket to the ceiling using the washers and screws found in bag C1, C2 or C3, according to the type of support structure you are installing the ceiling fan on to.

Standard Bracket

Angled Bracket

BAG

ATTENTION: for this installation, you must use the

included 12" downrod or you may need a longer

one. Visit www.atomismart.com to find additional downrod options. In step 4, you will find the

instructions to replace the downrod.

PREVENT FAN FALLING INJURY OR

DEATH. Make sure all three screws

are tight to secure the trim ring to

WARNING

the mounting plate.

Standard bracket maximum angle =
15 degrees

Up to 15°

Angled bracket maximum angle =
35 degrees

Between 15° to 35°

FOR THIS STEP YOU WILL NEED 12" DOWNROD

REPLACING THE DOWNROD (OPTIONAL)
This step is for Standard and Angled Mounting only. For the Flush Mounting (pre-assembled) go to Step 5. If you have a longer downrod from Atomi Smart, please, follow the same instructions.
If you are using the Angled Bracket, please use the Angled Canopy when prompted on the next page.

PREVENT FAN FALLING INJURY OR DEATH:

· ALWAYS tighten screws with a screwdriver or a drill.

WARNING

· DO NOT hand tighten screws. · CHECK the screws are tight using screwdrivers each time you change fan direction.

Standard or Angled Mounting

1
Detach the red, white, and black wires from the wire splitter. Unplug the white and black wires.

2
Lift the canopy and funnel.

3
Locate and remove the clip and pin.
3 2 1
4
Loose the screws and remove the downrod, canopy, and funnel.
11

5
Remove the clip and pin from the new downrod.

8
Tighten the screws.

9
Slide down the funnel.

3 2
1

Insert the canopy and funnel

into the downrod, passing all

wires through the downrod.

7
Keep the canopy and funnel up and insert the pin and clip.
1 2

Re-attach the wires to the wire splitter, matching the colors. Plug the white and black wires.

Note: Use the canopy to place the exceeded wires.

5
HANGING THE FAN
Lift and carefully hang the fan on the mounting bracket.
14

FOR THIS STEP YOU WILL NEED
BAG
D

WIRING THE FAN
Carefully follow these steps to get your fan wired safely and quickly. If you are unfamiliar with wiring or uncomfortable doing it yourself, please contact a qualified electrician.

THE CEILING FAN MUST BE GROUNDED.

If the ground wire for the installation site

is not present or you're unsure what this

WARNING

means, immediately STOP installation

and consult a qualified electrician.

WIRING MUST BE UP TO CODE. All wiring

must be in accordance with national and

local electrical codes. If you are unfamiliar

WARNING

with wiring or in doubt, consult a

qualified electrician.

1
Slide the remote receiver between the mounting bracket and the top of the downrod.

2
Push the bare metal ends of the wires together and slide a wire nut over them. Twist the wire nut clockwise until tight.
Give it a gentle pull to ensure none of the wires come apart.

2.1

2.2

2.3

Connect the BLACK (ungrounded) wire from the RECEIVER to the BLACK
wire from the CEILING.

Connect the WHITE wire from the RECEIVER to the WHITE wire from
the CEILING.

Connect the GREEN (grounded) wire from the FAN to the GREEN OR BARE wire
from the CEILING.

3 1
2

FOR THIS STEP YOU WILL NEED

INSTALLING THE CANOPY

1
Lift the canopy into place so that the screw holes are aligned with the housing holes. Fit the canopy in place as shown (1) and turn it clockwise.

2
Tighten the screws.

HAVE EXTRA WIRING? Turn the wires upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the
outlet box. Make sure that the wires are still attached to the wire nuts.

INSTALLING THE GLASS SHADE

PREVENT GLASS FALLING. Make sure that glass is properly secured.
WARNING

Lift the glass shade and align the notches in the glass shade with the tabs in the light ring.

Attach the glass shade by lifting and turning it clockwise one-third of a full turn until it stops. NOTE: Check to ensure proper engagement.

FOR THIS STEP YOU WILL NEED

BAG
E1

USING THE REMOTE CONTROL
Note: Requires 2 AAA batteries (not included).

Control buttons

Light Switch Press to turn the light ON/OFF
Warm Press to increase the white light warmness by 10%. Hold the button to quickly increase to maximum levels
+ Speed Press to increase the fan speed (Low,
Medium, High). Hold the button to quickly increase to High
Fan Switch Press to turn the fan ON/OFF
- Speed Press to decrease the fan speed (Low,
Medium, High). Hold the button to quickly decrease to Low

Brightness

Warm

On/O

Cool

Brightness

Speed

On/O

4H
Timer

Speed

+ Brightness Press to increase the light brightness by 10%. Hold the button to quickly increase to maximum levels
Cool Press to increase the white light coolness by 10%. Hold the button to quickly increase to maximum levels
19
- Brightness Press to decrease the light brightness by 10%. Hold the button to quickly decrease to minimum levels
4H Press to quickly add a 4-hour Timer to turn off your ceiling fan blades

3
Turn on the circuit breakers to the outlet box associated with the wall switch location, then turn on the wall switch and check if the Atomi Smart WiFi Ceiling Fan starts flashing white light.
If it does not flash a white light, please, check all wiring connections for any wrong connections.
If it does flash a white light, please, proceed to the next step.

Attaching to an existing light switch
Note: This is only compatible with toggle switches.

1
Remove the screws from your light switch cover (Do not remove the cover).

2
Place the Remote Control Mount over the cover and attach it with the cover's screws.

Mounting it to the wall

20
1
Place the Remote Control Mount on the wall and make the guide
holes with a pencil.

BAG
E2
2
Drill holes for the included anchors (if applicable).

3
Attach the Remote Control Mount to the wall with the included screws and anchors.

Now that your Smart WiFi Ceiling Fan is installed, it is time to connect and start using it.
Connecting your Smart WiFi Ceiling Fan

1
GET

21
2
Register

Get the app
Download the Atomi Smart app from the App Store or Google Play.

Register
Follow the on-screen instructions and register an account.
Make sure to allow access to Location (Android), Bluetooth and Local Network (iOS).

Add Device

Turn on your Atomi Smart device
And confirm that the light is flashing white.
If not flashing, reset the light by following the Troubleshooting instructions.
22
5

Add your Atomi Smart device
Press "Add Device" or the "+" sign and select "Connect Device" on the popup that appears.
If the popup does not appear, close the app and try again. Still nothing? Read the "Troubleshooting" section on this user guide.

WiFi Password
Continue

Select the right network
Enter your home WiFi name and password, then press "Continue"
Make sure you're connected to a 2.4GHz WiFi network (Atomi Smart can't connect to 5GHz networks).

USING THE BALANCE KIT
Follow these steps to properly even out the blade weight distribution.

1
Ensure your fan in correctly installed and all fasteners are secure. It is recommended the fan run on HIGH for 10-20 seconds to perform these next steps.

2
Pause your fan to attach the clip to the end of any blade. Run your fan and observe the wobble. Stop the fan and move the clip to the next blade,
repeating these steps for all the fan blades.

3
Now, move the clip to the blade that caused the least wobble. Run your fan and observe the wobble. Adjust the clip in small increments along the edge of the blade to achieve the least wobble.

23
4
At the location where you noticed the least wobble, adhere the
balance weight and remove the clip.

TROUBLESHOOTING

The popup does not appear when

I'm getting "Failed to Add Device",

adding a device.

"Failed to find router" or "DHCP" error.

Make sure that you are allowing the app to

- Confirm that your phone is connected to a

access your phone's Location (Android), Bluetooth

2.4GHz WiFi network.

and Local Network (iOS). For more details, visit our - Check whether the router password you

website's Support page.

entered is correct.

If the popup still doesn't appear, follow the steps

- Confirm that the DHCP service is enabled on

below:

your router settings.

1. Press "Add Device" or the "+" sign and select

- Make sure that your WiFi signal is strong.

your Atomi Smart device.

- Temporarily disable your 5GHz network.

2. Follow the on-screen instructions (Make sure

- If you have a mesh network/router that does

you connect to a 2.4GHz WiFi Network).

not allow you to disable 5GHz, try to move

farther away from your router until your phone

I can't find the atomi-smart-XXXX network in my WiFi list.
Make sure your Atomi Smart device is powered

moves to the 2.4GHz band. - For more Connection Troubleshooting tips, visit
atomismart.com/connection-troubleshooting/

on and the light is flashing white. If not, reset your device.

My Atomi Smart device appears as "Unavailable" or "Offline" in the app.

24 My WiFi network doesn't appear in the Refresh the device list.

Atomi Smart app.
Use your smartphone to confirm that you have

I just replaced my router.

at least two WiFi bars in the vicinity of your Atomi

If you replace your router, you will need to reset

Smart device. If not, move your Atomi Smart device your devices and add them again to the app.

closer to your router. (The list will refresh every 10 seconds).

How to reset my device?

Turn off the light switch

Cannot connect to my WiFi network.
Make sure that you have entered the correct WiFi password during the WiFi setup. Check if there are problems with your internet connection. If the WiFi signal is too weak, reset your WiFi router and try again.

- Turn ON, OFF and wait 1-2s - Turn ON, OFF and wait 1-2s - Turn ON, OFF and wait 1-2s - Turn ON, OFF and wait 1-2s - Turn ON and wait a few seconds. The light
should start flashing white.

The Ceiling Fan does not work
- Make sure that the circuit breaker power is turned on.
- Confirm that your wall switch is on. - Turn off the power from your circuit breaker
and check the fan's wiring for any connection issues.

The Ceiling Fan is too noisy
Confirm that the blades are properly installed.
The Ceiling Fan is wobbling
- Confirm that the downrod was correctly attached to the mounting bracket.
- Make sure that the mounting screws are firmly screwed in.
- Confirm that the canopy is firmly attached to the mounting bracket.
- Note any warped blades. If even one blade is slightly distorted, it can create an imbalance. Check for warping by standing on a secure ladder and looking down the edge of the blade

toward the motor. If there's any curvature, the blade is considered warped. Repeat this step for every blade. If they do not appear uneven, confirm that the screws that attach the blades are tightened and secure. Warped blades cannot be balanced. Use the included balance kit to even out the blade weight distribution. Directions on how to use it can be found on page 23.
Remote Control doesn't work
- Make sure that the AAA batteries (not included) are correctly in place.
- Replace the batteries with new ones.

For more information about app and device features, tutorials and troubleshooting tips go to: www.atomismart.com/helpCeilingFan

25
STILL CAN'T CONNECT? NEED ASSISTANCE?
Our friendly customer service team will work hard to put a smile back on your face.
Here's how we can connect.

1-800-757-1440 Mon-Fri 9:00-5:00 EST (US)
or support@atomiusa.com

WELCOME TO THE ATOMI SMART FAMILY!
We know you will love our products so much that we are giving you an exclusive 15% off your next purchase on atomismart.com.

Log onto https://atomismart.com/shop-now/

Add to Cart

Enter promo code ATOMI15OFF

Proceed to checkout

Free shipping on orders over $50 *within the contiguous US only*

Terms and conditions apply.

The following terms and conditions apply to the promo code:
1. Coupon is only valid on the Atomi Smart website www. atomismart.com.
2. A valid code must be entered at the checkout page in order to redeem the promotion.
3. Customers can only redeem one time at checkout. 4. Customers can only use the promo code once. 5. Atomi Smart reserves the right to cancel or modify any
order, or revoke the use of the promo code for any reason. 6. Unless otherwise stated, promo codes are not valid in
conjunction with other promotions or discounts.

7. Additional terms and conditions may be specified in relation to specific promo code (for example, duration, eligibility, discount amount and products covered), and will govern the use and redemption of those vouchers.
8. Promo code is not exchangeable for cash. 9. Atomi Smart will not be liable and/or be required to offer
replacement codes, discounts, credits, cash or otherwise compensate customers for: a. discontinued or cancelled promo code; b. improper use of, or inability to redeem, a promo code; or c. the inability to redeem promo code due to technical issues.

FCC Notice: This device complies with Part 15 of the FCC Rules. Operation is subject to the two following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired
operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Warning This product can expose you to chemicals including Lead, which is known to the State of California to cause birth defects or other reproductive harm. For more information,go to www.P65Warnings.ca.gov.
27
Limited lifetime warranty from the date of purchase against defects in material and workmanship.
For questions or concerns, email us at support@atomiusa.com Manufactured and marketed by Atomi Inc. 10 West 33rd St., New York, NY 10001 atomiTM is a trademark of Atomi Inc. atomi smart® is a registered trademark of Atomi Inc. Designed by Atomi in New York. Made in China.

References

Adobe PDF Library 16.0.5 Adobe InDesign 17.1 (Macintosh)