Insteon Wall Switch Owner's Manual
Getting Started
Everything you need to quickly get up and running.
Insteon Wall Switch Types
The Insteon Wall Switch is available in several configurations:
- Dimmer Switch & On/Off Switch: Features brightness LEDs, a status LED, a set button, and paddle for On/Off control. Holding the paddle brightens or dims the light.
- High-Wattage Dimmer Switch: Similar to the standard dimmer but includes a heat sink tab and is rated for higher wattage.
Switch Controls:
- Brightness LEDs: Indicate brightness levels.
- Status LED: Provides device status information.
- On/Off Paddle: Tap to turn On/Off. Press and hold to adjust brightness.
- Set Button: Used for linking and programming functions.
Tools Needed for Installation
- Phillips Screwdriver
- Flathead Screwdriver
- Voltage Detector
- Wire Cutter / Stripper
Disconnect Power
⚠️ Always disconnect power before installation. Contact Insteon Support if uncertain about installation.
Support Phone: 1-866-243-8022
Installation
Follow these steps to install your Insteon Wall Switch:
- Unbox and read instructions.
- Disconnect Power: Turn off power to your switch at the electrical service panel (Circuit Breakers or Fuse Panel).
- Remove the Old Switch: Disconnect the wires from the old switch. If your box lacks neutral wires, stop and contact support.
- Identify Line and Load wires: Use a voltage detector or multi-meter to identify the line and load wires. The line wire will be energized.
- Wire-In The Switch: Turn off power at the circuit breaker again. Connect the Wall Switch wires to the identified wires in the junction box. Ensure wire nuts are secure and no exposed copper wire is visible, except for the bare ground wire. Additional wiring diagrams are available in the 'Installation Diagrams' section.
- Install the Switch: Mount the Wall Switch into the junction box, ensuring the LED bar is on the left.
- Reconnect Power: Turn power back on to the switch at the circuit breaker panel.
- Test the Switch: Tap the paddle to turn the connected load On and Off. Press and hold the paddle to dim or brighten.
- Install Wall Plate: Complete the installation by attaching your wall plate. For a seamless look, consider an Insteon Screwless Wall Plate.
Installation of your Wall Switch is now complete. ✔️
Installation Diagrams
Use the following diagrams to help wire your Wall Switch, from single-switch to multi-way configurations.
Standard Switch Wiring
Diagram Description: Shows a single Insteon Wall Switch connected to a load. Wires are labeled: Load, Line, Neutral, Ground.
Three-Way Switch Wiring
Diagram Description: Illustrates a three-way switch setup with two Insteon Wall Switches controlling a single load. Wires are labeled: Load, Line, Neutral, Ground, and Traveler (Not Used). One switch connects to Line, the other to Load. Both switches connect to Neutral and Ground. Traveler wires connect between the two switches.
Four-Way Switch Wiring
Diagram Description: Depicts a four-way switch setup with three Insteon Wall Switches controlling a single load. Wires are labeled: Load, Line, Neutral, Ground, Traveler 1 (Not Used), and Traveler 2 (Not Used). The configuration involves complex interconnections between the switches via traveler wires.
Insteon Links
Insteon devices can operate independently or connect to form a powerful control system. Linking associates multiple Insteon devices, allowing them to control each other.
Understanding Linking
- Links are One-Way: A link from device A to device B means A can control B, but B cannot control A.
- Links Remember Device State: The controlled device's current state (On, Off, or brightness level) is stored in the link. For example, a switch can turn a lamp dimmer to 75% brightness.
- Controllers: Devices that initiate commands (e.g., Sensors, Switches, Keypads, Hub).
- Responders: Devices that receive commands (e.g., Switches, Keypads, Plug-In Modules, LED Bulbs).
- Controller-Only: Devices that can only send commands (e.g., Motion Sensor).
- Responder-Only: Devices that can only receive commands (e.g., LED Bulb).
- Grouping Devices / Cross Linking: Allows multiple devices to control each other, useful for virtual three-way configurations. This requires linking devices in both directions.
Linking to the Insteon Hub
- From the Insteon Hub app, navigate to 'Rooms' and then 'All Devices'.
- Tap the 'Add' button.
- Select 'Wire-In Device' from the list.
- When prompted, press and hold the set button on your Wall Switch until it beeps. Your Wall Switch is now added to your Insteon Hub. ✔️
Linking with a Single-Button Controller
- On your Insteon Wall Switch, press and hold the set button until the device beeps. ?
- Adjust your responder device to the desired state (On, Off, or brightness level). Then, press and hold its set button until it double-beeps. ??
Your Insteon Wall Switch will now control your Insteon device. ✔️
Linking with a Multi-Button Controller
- Press and hold the set button on your Wall Switch. ?
- On your multi-button Insteon device, tap the desired button (e.g., A or B) and then press and hold its set button until the device beeps. ?
Your Wall Switch will now control a specific button on your multi-button Insteon device. ✔️
Multi-Linking or Making a Scene
- On your Insteon Wall Switch, press and hold the set button until the device beeps. ? Then, tap the set button.
- Adjust the devices in your scene to their desired states (e.g., Lamp 1 at 50%, Lamp 2 at 72%, Lamp 3 at 30%, Appliance ON).
- One at a time, press and hold the set button on each device in the scene until it double-beeps. ??
- Tap the set button on your Wall Switch to finish building your scene.
Your Wall Switch will now control your scene. ✔️
Unlinking from a Single-Button Controller
- On your Insteon Wall Switch, press and hold the set button until the device beeps. ?
- Press and hold the set button again until the device beeps. ?
- Press and hold the controlled device's set button until it double-beeps. ??
Your Wall Switch will no longer control that Insteon device. ✔️
Unlinking from a Multi-Button Controller
- On your Insteon Wall Switch, press and hold the set button until the device beeps. ?
- Press and hold the set button again until the device beeps. ?
- On your multi-button Insteon device, tap the desired button (e.g., A or B) and then press and hold its set button until it double-beeps. ??
Your Wall Switch will no longer control that button on your multi-button Insteon device. ✔️
Multi-Unlinking or Removing a Scene
- On your Insteon Wall Switch, press and hold the set button until the device beeps. ? Press and hold the set button again, then tap the set button.
- One at a time, press and hold the set button on each device in your scene until it double-beeps. ??
- Tap the set button on your Wall Switch to exit Multi-Unlinking mode.
Your Wall Switch will no longer control your scene. ✔️
Local Programming
Encompassing all on-device programming options, use local programming to set local properties. For the best experience, use software for managing device properties.
Navigating the Chart
Instructions:
- To move right: Press and hold the set button.
- To move down: Tap the set button.
Status LED Indicators:
- Status LED blinks green
- Status LED double-blinks green
- Status LED blinks red
- Status LED double-blinks red
Features and Modes
| Mode/Feature | Description |
|---|---|
| Linking Mode | Prepares the module for linking to another Insteon module. The first device becomes the controller, the second the responder. Exits automatically after a link is made. |
| Multi-Linking Mode | Prepares the module for linking to multiple Insteon modules. Remains active for 4 minutes or until the set button is tapped. Useful for creating scenes. |
| Unlinking Mode | Allows removal of links from the Insteon module. Exits automatically after a link is removed. |
| Multi-Unlinking Mode | Allows removal of multiple links. Remains active for 4 minutes or until the set button is tapped. |
Flow Chart Overview
The flow chart details various functions accessible via the set button:
- Linking Mode: Initiated by pressing the set button.
- Unlinking Mode: Initiated by pressing the set button.
- Multi-Linking Mode: Select to initiate.
- Multi-Unlinking Mode: Select to initiate.
- LED Brightness: Adjust brightness or select 'Adjust'. Press 'Cancel' to exit.
- On Level: Uses current brightness. Press 'Save' to confirm.
- RF Beacon: Toggle or cycle through four presets. Press 'Save' to confirm.
- Ramp Rate: Select to adjust speed. Press 'Save' to confirm.
- Factory Reset: Select to initiate. Press 'Reset' to confirm.
- Resume Dim: Uses current brightness. Press 'Save' to confirm.
Factory Reset
A factory reset erases all stored links and reconfigures the device to factory defaults.
- Pull the set button out from the switch until the status LEDs turn off.
- Wait approximately ten seconds. 10 Seconds
- Push in and hold the set button until the long beep subsides. LONG ?
- Release the set button. The switch will double beep. ??
? For older switches that do not produce a long beep, press and hold for 10 seconds.
Your Wall Switch has been restored to factory settings. ✔️
Software-Only Features
Most Insteon devices have features that can only be enabled, disabled, or modified using Insteon control software (e.g., HouseLinc, Insteon PowerLine Modem).
- Beep on Button Press: The Wall Switch beeps when a button is tapped. By default, this feature is disabled. ?
- Blink on Traffic: The Wall Switch LED blinks when Insteon communication is detected. By default, this feature is disabled.
- Disable Local Programming: Prevents changing settings via the set button or tap-and-hold programming. ❌
- Error Blink: The Wall Switch LED blinks red if responders do not acknowledge a message, and green if they do. By default, this feature is enabled. ✔️❌
- LED Brightness: Adjust the brightness of the status LEDs from full bright to off.
Appendix
Everything else you might need to know about your Insteon product.
Insteon Glossary
| Term | Definition |
|---|---|
| Controller | The Insteon transmitter. |
| Responder | The Insteon receiver. |
| Blinking | LED turning on and off repeatedly. |
| Dual-Band | An Insteon device that can send and receive both Insteon powerline signals and Insteon radio frequency signals. |
| Ramp Rate | The speed at which the load fades on or off. |
| On-Level | The preset brightness level a device will return to when turned on. |
| Insteon | A dual-band, mesh networking technology developed by Smarthome/Insteon, known for reliability and simplicity in home automation. |
| Link | A one-way association between a controller and responder. |
| Linking | Associating Insteon controller buttons with groups of Insteon responders to recall a memorized state. Can be done manually or via software. |
| Unlinking | Removing stored links from an Insteon device. A one-way process, performed in both directions for devices that act as both controllers and responders. |
| Multi-Linking / Unlinking | A mode allowing multiple links to be created or removed simultaneously. Active for 4 minutes or until the set button is tapped. |
| Factory Reset | Erases all stored links and reconfigures the device to factory defaults. |
| Load | The device being controlled (e.g., light bulb, ceiling fan). |
| On/Off | A device that controls its load to turn on/off but cannot dim. Typically a relay-based device. |
| Retry | An attempt by a controller to resend an Insteon signal if acknowledgment is not received. |
| Scene | Multiple devices responding to memorized states (e.g., a 'dinner time' scene). |
| Set Button | A button on an Insteon device used for setting or changing properties. |
| Simulcast | A method to increase message delivery reliability by having nodes retransmit messages simultaneously. |
| X10 | A legacy powerline networking technology compatible with many Insteon devices. |
Specifications
| Category | Specification |
|---|---|
| General | |
| Available Colors | White |
| Brand | Insteon |
| FCC ID | SPB2477 |
| Industry Canada | 5202A-24772 |
| Product Number | 2477S On/Off Switch, 2477D Dimmer Switch, 2477DH Dimmer Switch (High Wattage) |
| Patent | Protected under US and Foreign Patents (see www.insteon.com/patents) |
| UPC | 813922012378 (On/Off Switch), 689076401746 (Dimmer Switch), 813922011005 (Dimmer Switch High Wattage) |
| Warranty | 2 years, limited |
| Operation | |
| On-Levels | 32 locally, increments of 1% with software |
| Ramp Rates | 0.125 seconds to 8 minutes |
| Status LED | 9 White LEDs |
| Operation Modes | Insteon |
| Multi-Way Circuit Support | Yes, one switch controls the load; others are secondaries. |
| Setup Memory | Non-volatile EEPROM |
| Insteon Features | |
| Insteon Addresses | 400 |
| Insteon Device Category | 0x01 |
| Insteon Device Subcategory | 0x00 |
| Insteon ID | 1 |
| Insteon Links | 417 |
| Insteon Messages Repeated | Yes |
| Insteon Powerline Device | Yes |
| Insteon RF Device | Yes |
| Maximum Controlled Scenes | 1 |
| Maximum Scene Memberships | 1 |
| Multi-Link Support | Yes |
| Multi-Unlink Support | Yes |
| Phase Detect Beacon | Yes |
| Radio Frequency | 915.0 MHz US |
| Radio Frequency Range | 150 feet |
| Scene Commands Supported as Controller | On, Fast-On, Begin Brighten, End Brighten / Off, Fast-Off, Begin Dim, End Dim |
| Scene Commands Supported as Responder | On, Fast-On, Begin Brighten, End Brighten / Off, Fast-Off, Begin Dim, End Dim |
| Software Configurable | Yes |
| Mechanical | |
| Paddle Type | True rocker action |
| Wire Nuts | 4 Included |
| Mounting | Single or multi-gang junction boxes. Derating of 200W for each immediately adjacent dimmer. |
| Dimensions | On/Off and Dimmer Switch: 4.1" H x 1.8" W x 1.2" D (104mm x 46mm W x 31mm D) Dimmer Switch (High Wattage): 4.1" H x 2.5" W x 1.2" D (104mm x 64mm W x 31mm D) |
| Operating Environment | Indoors |
| Operating Humidity Range | 0-90% relative humidity, non-condensing |
| Operating Temperature Range | -40° to 104° F (-40° to 40° C) |
| Set Button | 1, recessed. Requires removal of sensor to access. |
| Storage Temperature Range | -40° to 104° F (-40° to 40° C) |
| Weight | 3.6 oz (102g) |
| Electrical | |
| Supply Voltage | 100-277 Volts AC ± 10%, 50/60Hz, Single Phase |
| Neutral Wire | Required |
| Power Wire Leads | 6" 16 AWG stranded 600V (Line, Load, Neutral) |
| Maximum Amperage | 5 amps |
| Ground Lead | 6" 18 AWG stranded bare copper |
| Power Consumption | 0.59 Watts |
| Certification | ETL 3017581 |
Troubleshooting
- LED Lights Not Illuminated: Check power supply and circuit breaker. Ensure wire connections are secure. Status LEDs may be disabled via software.
- Unable to Add to Scene/Responder: Powerline noise from large appliances or electronics may interfere. Check GFCI outlet connections. Consider noise filters. Ensure sufficient range between devices; use a Range Extender if necessary.
- Slow Response to Commands: Likely due to the controller repeating commands for devices removed from the network. Remove old links from the controller or perform a factory reset on the controller.
- Connected Light Turns On By Itself: An unexpected link may exist. Examine the Wall Switch's links and remove any stray controllers. Perform a factory reset if the controller is unknown. If using X10 addresses, try assigning a different one.
- Switch Turns Off But Not On (via controller): The link may have been set to 'Off'. Re-link the device to the controller with the load on.
- No Response to Button Taps or Controller Links: A power surge or excessive powerline noise may have occurred. Temporarily disconnect power by pulling the set button out, wait 10 seconds, then push it back in. A factory reset may be required.
- Long, Continuous Beep After Installation: Indicates incorrect wiring. Turn off power and verify all wire connections are secure, properly labeled, and that no bare wire is exposed. Use a voltage detector or multi-meter to identify Line, Load, and Neutral wires correctly. Contact an electrician if unsure.
Certifications and Warnings
This device complies with FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any interference. Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate the equipment and the manufacturer's warranty.
The digital circuitry complies with Class B limits per FCC Rules, designed for residential installations. If interference occurs, users are encouraged to:
- Re-orient or relocate the receiving antenna.
- Increase distance between this device and the receiver.
- Connect to a different AC circuit.
- Consult a dealer or experienced radio/TV technician.
WARNING: Unauthorized modifications void user authority and warranty.
Product Warranty
Limited Warranty: Insteon warrants this product to the original consumer purchaser for two years from the date of purchase against defects in material and workmanship. This warranty does not cover misuse or neglect. If defective, Insteon will repair, replace, or refund the purchase price at its option. For warranty service, call 866-243-8022 to receive an RMA# and shipping instructions.
Address for Returns:
Insteon
ATTN: Receiving
16542 Millikan Ave.
Irvine, CA 92606-5027
Limitations: This warranty is exclusive and in lieu of all other warranties. Implied warranties are limited to the two-year period. Insteon is not liable for special, incidental, or consequential damages. Home automation devices are conveniences, not sole control methods.
Protected under U.S. and foreign patents. ©2015 Insteon.
