User Manual for Whirlpool models including: WR619CHAUS 4 Zone Ceramic Cooktop, WR619CHAUS, 4 Zone Ceramic Cooktop, Ceramic Cooktop, Cooktop
EN INSTALLATION · The cooktop must be set into a worktop at least 20 mm deep. · There must be nothing between the cooktop and the oven (cross rails, brackets, etc.). · Make sure the power cord is long enough to allow convenient installation. · The distance between the lower face of the glass ceramic hob and the cupboard or separating panel must be at least 20 mm. min. 20 mm · For built-in dimensions and installation see the picture in this paragraph. · A minimum distance must be maintained between the hob and the hood above it. Please refer to the user manual of the hood for more informations. · Apply the supplied gasket to the cooktop (unless it has already been fitted), after having cleaned its surface. · Do not install the cooktop near a dishwasher or washing machine, so that the electronic circuits do not come into contact with steam or moisture, which could damage them. · If an oven is installed beneath the cooktop, make sure that it is equipped with a cooling system. If the temperature of the electronic circuits exceeds the maximum permitted temperature, the cooktop will switch off automatically; in this case, wait for a few minutes until the internal temperature of the electronic circuits reaches a tolerable level, at which point it will be possible to switch the hob on again. · ATTENTION: to install the hob on other surfaces than wood (marble, plastic, ceramic, marble, stone, etc.) remember to ask After Sales Service for the fixing plates (fig. 2) Code 4819 404 78697. PLACING THE HOB Important: remove any protective film before installing the hob. Make sure that the opening in the worktop for the hob is cut according to the dimensions given in the drawing, paying attention to the tolerance range. The hob should not be forced into the worktop. Forcing the glass-ceramic top may cause it to crack (even at a later date)! If the worktop is made of wood, use the spring clips and screws provided. Secure the spring clips (A) (fig. 1) with the screws provided (B) (fig. 1) as shown, paying attention to the specified distances. Fit the hob into the worktop. If the worktop is made of marble, plastic, ceramic, stone, etc., the hob must be secured with special brackets (C) (fig. 2). Fit the hob into the worktop (fig. 1). Place the 4 brackets (C) in position in accordance with the thickness of the worktop as shown in fig. 2. Fasten the 4 screws (D) in the positions (E) (fig. 2). BA 145 ± 1mm 200 mm 1 DIMENSIONS AND DISTANCES TO BE MAINTAINED i Min. 5 cm L Min. 40 cm Min.10 cm CD CD E 40 mm 30 mm 50 mm CD 2 50 mm 580 mm 482 mm 510 mm 552 mm Min. 20 mm 490 - 492 mm Min. 6,5 mm Max. 16 mm Min. 50 mm 560 - 562 mm REMOVING THE HOB: To remove the hob, first, disconnect it from the electric supply. It is strongly recommended to free the underneath part from the oven, drawer, separator, or other. It allows the technician to access the lower part of the hob to unfasten the four clips with a screwdriver, lift the hob and remove it, avoiding any worktop damage. ELECTRICAL CONNECTION Electrical connection must be made before connecting the appliance to the electricity supply. The power cord is not included in the package - remember to prepare your own power cord. Installation must be carried out by qualified personnel who know the current safety and installation regulations. Specifically, installation must be carried out in compliance with the regulations of the local electricity supply company. Make sure the voltage specified on the data plate located on the bottom of the appliance is the same as that of the home. Regulations require that the appliance be earthed: use conductors (including the earth conductor) of the appropriate size only. CONNECTION TO THE TERMINAL BLOCK For the electrical connection, use an H05RR-F or H05V2V2-F cable as specified in the table below. SUPPLY VOLTAGE 230-240V ~ + 220-240V 3 ~ + 380-415V 3N~ + 380-415V 2N~ + CONDUCTORS AMOUNT x SIZE 3 x 2,5 mm2 4 x 1,5 mm2 5 x 1,5 mm2 4 x 1,5 mm2 F G The appliance must be connected to the electricity supply by means of an all-pole disconnect switch with minimum contact gap of 3 mm. ATTENTION: the power supply cable must be long enough to allow the cooktop to be removed from the worktop and must be positioned so as to avoid damage or overheating caused by contact with the base. NOTE: the yellow/green earth wire must be connected to the terminal with the symbol and must be longer than the other wires. · Remove approx. 70 mm of the cable sheath from the power supply cable (G). · Strip approx. 10 mm of sheath from the wires. Insert the cable (G) through the opening in the lid (F). · Insert the cable into the cable clamp and connect the wires to the terminal block as indicated in the diagram printed on the lid. · Secure the power supply cable (G) by means of the cable clamp. · Refit the protection lid (F). · After the electrical connection, fit the hob from the top and hook it to the support springs, according to the illustration. PRODUCT DESCRIPTION 1. Radiant cooking zone 145 mm 2. Radiant cooking zone 210 mm 1 3. Radiant cooking zone 145 mm 2 4. Radiant cooking zone 180 mm 5. Rear right cooking zone control knob 5 6. Rear left cooking zone control knob 6 7. Front left cooking zone control knob 3 7 8. Front right cooking zone control knob 8 4Adobe InDesign 18.1 (Windows) Adobe PDF Library 17.0