User Guide for TOYBOX models including: 2BGPC-COMET, 2BGPCCOMET, 2BGPC-COMET 3D Printer, 2BGPC-COMET, 3D Printer, Printer
TOYBOX LABS INC COMET 3D printer 2BGPC-COMET 2BGPCCOMET comet
Qui ck- st ar t gui de - Engl i sh440mm x160mm 300gsm mat t e coat ed paper Pant one 172 U pr i nt i ng The ESP32- WROVER- E and ESP32- WROVERI E use t he ESP32- DOWD- V3 " chi p f r om t he ESP32 ser i es. The ESP32- DOWD- V3 chi p has t he char act er i st i cs of scal abi l i t y and adapt abi l i t y. Two CPU cor es can be cont r ol l ed separ at el y. The adj ust ment r ange of CPU cl ock f r equency i s f r om 80 MHz t o 240 MHz. User s can t ur n of f t he power of t he CPU and use l ow- power copr ocessor s t o moni t or t he st at us changes of per i pher al s or whet her cer t ai n anal og quant i t i es exceed t hei r val ues. ESP32 al so i nt egr at es a var i et y of per i pher al s, i ncl udi ng capaci t i ve t ouch sensor s, Hal l sensor s, SD car d i nt er f aces, Et her net i nt er f aces, hi gh- speed SPI , UART, I PS, and PC. 152mm 155.5mm The l ef t Account , f ar l ef t ' I nser t ' but t ons ar e Food, Wi Fi , and About . On t he of t he r i ght but t on ar e and ' Remove' . 156mm Connect t he phone t o t he di spl ay scr een and i nser t t he scr een wi t h t he r ocket i nt o t he machi ne. Connect t he r ecei ver . The ext er nal sensi ng emi ssi on devi ce can be act i vat ed af t er bei ng connect ed. 155.5mm Fi r st , i nst al l t he br acket ont o t he base, and t hen pl ace t he t abl et on t op of t he br acket . Next , f i x t he box wi t h handl es t o t he r i ght si de of t he base Fi r st , i nst al l t he br acket ont o t he base, and t hen pl ace t he t abl et on t op of t he br acket . Then f i x t he box wi t h handl e t o t he r i ght si de of t he base. Fi nal l y, use t he pr ovi ded wr ench t o f i r ml y f i x al l par t s and compl et e t he assembl y pr ocess I nst al l t he br acket st r uct ur e ont o t he base. I nser t t he wi r e i nt o t he wi r e hol e. I nser t t he ver t i cal descendi ng component i nt o t he base and embed t he ci r cul ar component i nt o t hat ar ea Open t he Wi Fi connect i on on your phone and assembl e t he assembl ed par t s. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. -This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.Adobe PDF library 16.07 Adobe Illustrator(R) 24.0