WIFI Signal Amplifier SH24Go10W

Part List

Please check the part list before the installation:

• SH24Go 10W
• DC injector
• 24V DC adapter
• Quick Installation Guide

NOTE: All connected cables need to be customized, because the application scenarios of different customers are different, so the required cable type and lengths are also different. If any missing or damaged parts are found, please contact your local vendor.

Hardware Installation Diagram

The diagram illustrates the connection process for the WIFI signal amplifier. It shows a DC injector unit, a USB WiFi Adapter (WD8811CU_D2), the SH24Go10W amplifier, and an antenna. The DC injector provides power through the coax cable to the amplifier. The setup involves connecting the DC injector to an Access Point (AP), then to the SH24Go10W, and finally to a power adapter. An antenna is shown mounted close to the amplifier for maximum gain.

Installation Steps:

1. Connect DC injector to AP.
2. Connect DC injector to SH24Go10W.
3. Connect DC injector to power adapter.
4. Power on the AP and SH24Go10W.

When the SH24Go10W is powered on, the power indicator on the DC injector will be steady Green.

Technical Specifications

Operating range

2400 ~2500 MHz

Channel width

20Mhz & 40 Mhz

Supported standards

IEEE 802.11 b/g/n

Operation mode

Bi-directional, half-duplex, time division duplex

Connector type

N-K female

Output power

10dBm

Input power

-30~26dBm

Transmit gain

22 dB

Receiver gain

≤20dB

Noise figure

≤ 3.5 dB typical

Frequency response

± 1dB over operating range

Power adapter

24V/2A DC, 100~240V

Operating temperature

-25 °C to +55 °C

Operating humidity

Up to 75% relative humidity

Material

Cast aluminum

LED light

Power status / activity status LED

Booster weight

470g

Booster size

15.2 x 7.3 x 2.6cm

CAUTION:

⚠️ Do not open the aluminum box without permission.

To prevent potential damage to the environment or to human health, please separate these products from other kinds of waste and recycle them properly. This helps foster the sustainable reusing of material resources. Home users can contact the establishment where they purchased the product or the corresponding local authorities to get information about how and where to take this waste for an ecologically safe recycling process. Major consumers can contact their provider and check the conditions of the purchase contract. Neither this product nor its electric accessories must be thrown away with other commercial waste.

This device must only be used in a system which has obtained authorization (FCC ID: 2AYN6-SH24GO10W).

Wireless USB WiFi Adapter User Guide

• External antenna, covering a wide range of signals.
• RTL811CU chip.
• 20m/40m bandwidth coexistence.
• Supports IEEE802.11 b/g/n.
• USB 2.0 interface.

Instructions

1. Users need to follow the driver file of this product. If it is a Windows 10 system, the driver may not be required.
2. When the driver is installed normally, the computer will display a wireless network card icon.
3. The user can scan and connect to the router's hotspot using the wireless configuration tool of the Windows system. The product can then be used normally.

Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Note: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.