User Guide for FOCALCREST models including: SRB01, 2AYEW-SRB01, 2AYEWSRB01, SRB01 In-Wall Relay Switch, In-Wall Relay Switch, Relay Switch, Switch
Focalcrest Limited SRB01 Smart Relay 2AYEW-SRB01 2AYEWSRB01 srb01
File Info : application/pdf, 2 Pages, 426.84KB
DocumentDocumentIn-Wall RELAY SWITCH
Smart RELAY* (Zigbee version)
Rev. A-031821
P/N SRB01
*Please see separate Smart SWITCH Sub-Assembly manual for complete instructions.
Smart Relay (1)
D
Heat-conducting sticker(1)
Fixing screw (1)
Instruction Manual (1)
SAVE THESE INSTRUCTIONS
·Warning! Turn OFF electrical powe befoe installing or servicing this product. Improper use or installation can cause SERIOUS INJURY, DEATH o LOSS/DAMAGE OF PROPERTY
·Warning! This device must be protected by a circuit breaker (20A max)
·Important: This device must be installed by a licensed electrician in accordance with all national and local electrical codes
·Caution: This poduct must not be wired to a circuit exceeding the rated working voltage
aut1on: Use this device only with copper or copper-clad wire. Do not use aluminum wiring. This product has not been approved fo use with aluminum wiring
·lmpotant: Using this product in a manner othe than outlined in this document voids your warranty Further, Focalcrest 1s NOT liable for any damage incured with the misuse of this product
·lmpotant: Please use this product in an indoor environment
·lmpotant: Please make sue that the type of load complies with relevant equirements of this device
·lmpotant: The wireless communication distance may be affected or reduced by metal casings, mirrors, electric appliances, etc
Technical Specifications
Model number
SRB01
Input Voltage
AC 85V-245V
Max Load Powe
AC 11 OV/300W AC 220V/600W
Min Load Power
No lim
Type of Load
Lighting
Operating Temperature
0-40'C (32 °-104 ° F )
Relative Humidity
5-85% RH
Wess Connectivity Zigbee 24GHz IEEE 80215.4
Zigbee Profile
Zigbee 30
RF Characteristics
Opeating frequency 24GHz Range 30m-60m Internal antenna
Product Size(L*W*H)
F r n t
F a s t e n n g s C re w R Es ET But t
594mm * 393mm * 212mm (234in x 155in x O83in)
.IX n g h e
ED
: Bottom 1
Panel Connection port
,: ;>·"'"
Output for load Wire Connection port
Step 3: Connect the w1es according to one of the two diagrams below 8 Connect the LIVE wire to the'L'terminal fJ Connect the NEUTRAL wire to the oute,N'tem1nal @ Connect the LOAD wire to the'OUT' 8(Fig. 3a only) Connect the NEUTRAL wie from the
light to the inner'N'terminal (}N
Step 4: Switch on the macircuit breaker to check if the wires are connected correctly. It they are correct, the LED light on the Smat Relay will be on Step 5: Shut off the main cicuit beakeaga Step 6: Stick the heat-conducting sticker at the recommended poson on the Smart Relay and fix 1t on a proper plane of the box.(Make sure the'antenna location area'is not blocked)
Smart Relay Sub-Assembly uses Zigbee wess technology and may be used in diffeent loads, including incandescent lamps, halogen lamps, LED lamps and fluoescent lamps. It is small in size and may be installed 1n the box of light fixtures. This device is compatible with standardgbee 3.0 gateway or devices for remote control and inter-opeation
Caution: All installations of this device should be peformed by a qualified o licensed electrician!
Step 1: Please note that 1f your Z1gbee 3.0 gateway adds devices by scanning QR codes, please scan the device identification QR code on the device before installation
Step 2: Shut off the main cicuit beake(MCB) for safety during the installation
,
------------Recommen ded paste
,,,
U °
oooo ',,',','
A lo
--
n te
c a
at
re
-
n a
.
10
n
a n
,,'','
©
Step 7: Switch on the main circuit breaker(MCB) and check if the light can be tuned on
Adding to your Zlgbee network (Inclusion)
1. Set yourgbee 3.0 gateway into inclusion/pairing mode (Refer to the gateway's manual)
2. Set the Smart Relay into inclus,on/painng mode with eithe methods. The LED will slowly blink blue fo 30 seconds. a Short press the RESET button b. (Alternative) If the Smart Switch installed too, quickly toggle the mechanical switch panel over 1O times
3. If the Smart Relay 1s successfully paired, the LED will be solid blue
Removing from Zigbee netwok (Exclusion)
1. Remove the Smat Relay from your Zigbee 3.0 gateway 2. Press and hold the RESET button for more than 5seconds 3. lf the Smat Relay 1s removed, the LED will be solid red
Resetting to factory defaults
1. Press and hold the RESET button for more than 5seconds If the LED light 1s solid RED, the Smart Relay has been factory reset and all data have been cleaed
IndicatorLight Status
Desciption
Pairing mode
Normal Zigbee network working mode No Z1gbee network working mode Swrtch opeation
lndicatoLight Status The BLUE LED blinks slowly for 30 seconds The BLUE LED is always on
The RED LED is always on
The BLUE LED blinks once
Foca/crest Limited Warranty
Thank you fo puchasing In-Wall RELAY SWITCH Focalcrest Lited values your business and always strives to provide you the very best quality of service
1. HARDWARE PRODUCT LIMITED WARRANTY. Focalcrest warrants to the original end use puchase, ("Customer") of each new Focalcest product that such Focalcrest Product hardware and components ('Product Hadware"), when used ,n accodance with the technical specifications by Focalcest, will be free, in all material respects, of defects in materials and workmanship under normal use ("Limited Warranty"). This Limited Waanty is non-transferable and sets forth Focalcrest's sole and exclusive liability, and the sole and exclusive emedies availableelation to any non-conformity, defect o s,m claim
3. EXCLUSIONS NOT COVERED BY THIS LIMITED WARRANTY. This Limited Warranty does not cover, and Focalcrest and its supplies are not responsible fa (A} Damage, malfunction, or inoperability of the Focalcrest Product caused by:DEALER RECOMMENDED OR CERTIFlED BY Focalcrest
( i ) shippers or delivery services, or due to Customer impropely opening the Focalcrest Product packaging,
(ii) Operation, storage, or application of the Focalcrest Product outside of the environmental, temperature, and other specifications provided in the Documentation;
(iii) Acts of God, including, but not limited to, flood, fire, earthquake, lightning, electrical surges, or any othe external cause;
(iv) Any act beyond Focalcrest's direct control, including, but not limited to, unauthorized repair or installation by Custome or 3rd party, accident, abuse, misuse, neglect, use of 1ncompat1ble devices and accessories, operating the Focaest Product outside the pernitted or intended uses pov1ded in the Documentation, or any other reason besides a defect 1n material or workmanship;
( v ) Use of incorrect voltage lines, fuses, circuit breakers, or incompatible load types as set forth in the Documenta tion, or failure to provide adequate, continuous, compatible power to the Product, 1f applicable;
(vi) lnterfeence from radio frequencies, infrared sources, or obstacles,
(vii) Normal wear and tear, or failure to install, maintain, or epair the Focalcrest Product in accordance with the Documentation and the applicable prov,s,ons of law for theurisdiction where the Focalcrest Product is being installed;
(v1ii) Any product, part or software that has been moded to alter funct1onal1ty or capability without the expess written permission of Focalcrest,
(ix) Batteries and consumable parts (if any), unless damage occued due to a defect in materials or workmanship in the Focalcrest Product;
( x ) Cosmetic damage, including, but not limited to, scratches, dents and normal wear and tear;
(x1) Focalcrest Product 1n which the serial number has been removed or defaced; and
(xii) ANY DAMAGE, MALFUNCTION, OR INOPERABILITY ARISING FROM INSTALLATION, MAINTENANCE, OR PROGRAMMING PERFORMED BY AN INDEPENDENT CONTRACTOR, INCLUDING, WITHOUT LIMITATION, ANY
(B) any on-site labor costs incured by Customer for the diagnosis, emoval, repair, re-installation, and/or reprogramming of the Focalcrest Product;
(C) any non-Focalcrest hardwae, including the functionality of 3rd party products controlled or automated by Focalcrest Products or Software (a "Focalcrest System"), batteries or softwae product (manufacturers, supps, or publishers, other than Focalcrest may provide their own warranties to Customer for their products, but Focalcrest, insofar as permitted by law, provides non-Focaest Products only "AS IS"); and
(D) the cost of epairing or replacing, or compensation for, any property that is damaged when a Focalcrest Product does not work properly, eventhe damage was caused by a Focalcrest Product
FCC-ID: 2AYEW-SRB01
@CE
FCC Statement This device complies with part 15of the FCC rules. Operation is subject to the following two conditions
(1) this device may not cause hamful interfeence, and {2) this device must accept any interfeence eceived, including inteFerence that may cause undes,ed opeation
Changes or modifications not expressly approved by the party responsible fo compliance could void the use's authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits for a Class B d11tal device, pursuant to pat 15of the FCC Rules These limits are designed to povide reasonable potection against hamful intefeence in a es1dential installation
s equipment geneates uses and can radiate ad10 frequency enegy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there 1s no guaantee that inteference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television eception, which can be determined by turning the
equipment off and on, the user is encouaged to try to corect the interference by one or more of the following measures
- --Reorient or relocate the receiving antenna. - --Increase the separation between the equipment and
receiver. - --Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. - --Consult the dealer or an experienced radio/TV
technician for help.
Important Announcement Important Note Radiation Exposure Statement
This equipment complies with FCC ad1ation exposure l1m1ts set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiate and your body This tansmitte must not be co-located or opeating in conunction with any other antenna or transmitter
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your respons1bty to dispose of your waste equipment by handing it over to a designated collection point fo the recycling of electrical and electonic equipment waste
Rev. A-031821
P/N SRB01
Adobe Illustrator 24.3 (Macintosh) Adobe PDF library 15.00