LSG Pacer M5 Under Desk Fold Down Treadmill

I. IMPORTANT SAFETY INSTRUCTIONS

⚠ WARNING: Read all instructions before using this treadmill.

It is important your treadmill receives regular maintenance to prolong its useful life. Failing to regularly maintain your treadmill may void your warranty.

⚠ DANGER

To reduce the risk of electric shock, disconnect your treadmill from the electrical outlet prior to cleaning and/or service work.

DO NOT USE AN EXTENSION CORD:

DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY USING IMPROPER ADAPTERS OR IN ANY WAY MODIFY THE CORD SET.

• Install the treadmill on a flat level surface with access to a 220-240 volt (50/60Hz), grounded outlet.
• Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet and treadmill may result.
• Do not block the rear of the treadmill. Provide a minimum of 1 metre clearance between the rear of the treadmill and any fixed object.
• Place your unit on a solid, level surface when in use.
• When running, make sure the plastic clip is fastened on your clothing. It is for your safety, should you fall or move too far back on the treadmill.
• Keep hands away from all moving parts.
• Never operate the treadmill if it has a damaged power cord or plug. When damaged, these must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Keep the cord away from heated surfaces.
• Do not operate where aerosol spray products are being used or where oxygen is being administered. Sparks from the motor may ignite a highly gaseous environment.
• Never drop or insert any object into any openings.

• The treadmill is intended for in-home use only and is not suitable for commercial environments.
• To disconnect, turn all controls to the off position, remove the safety key, and then remove the plug from the outlet.
• The pulse sensors are not medical devices. Various factors, including the user's movement, may affect the accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in determining heart rate trends in general.
• Use the handrails provided; they are for your safety.
• Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
• Before undertaking any type of exercise program, it is recommended that you consult a doctor.
• Injuries to health may result from incorrect or excessive training.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• ⚠ WARNING: Heart rate monitoring systems may be inaccurate. If you feel faint stop exercising immediately.
• Children should not be allowed on or around the equipment, even when not in use.
• Children should be supervised to ensure that they do not play with this machine.
• Loose-fitting clothing or jewellery that could become an entanglement hazard should not be worn.
• Training shoes should be worn when using the equipment.
• Equipment must be used on a level and stable surface.
• All fixings should be checked before the equipment is used.
• All literature relating to the use of the equipment should be retained for future reference.
• Recommended operating temperature: 5-40°C.

⚠ Remove the safety key after use to prevent unauthorized treadmill operation.

II. IMPORTANT ELECTRICAL INFORMATION

⚠ WARNING!

• Route the power cord away from any moving part of the treadmill including the elevation mechanism and transport wheels.
• NEVER remove any cover without first disconnecting AC power.
• NEVER expose this treadmill to rain or moisture. This treadmill is not designed for use outdoors, near a pool, or in any other high humidity environment.
• This is a high-power item; please do not share the same outlet with other high-power machines such as fridges, air conditioning etc. Please choose an outlet exclusively for the machine and make sure the fuse is 10A.

Battery Safety

⚠ WARNING

THIS PRODUCT CONTAINS A BUTTON BATTERY THAT IS HAZARDOUS AND IS TO BE KEPT AWAY FROM CHILDREN

The battery can cause severe or fatal injuries in 2 hours or less if it is swallowed or placed inside any part of the body. Seek medical attention immediately if this occurs.

If suspected of swallowing the battery or otherwise placed inside any part of the body, please contact Australian Poison Centre immediately on 13 11 26. Hotline is open 24/7.

Call triple zero (000) immediately if you or someone you know stops breathing, slips into a coma, or has a seizure or a severe allergic reaction to suspected poisoning.

III. PARTS LIST

The treadmill includes the following main components:

• Display Panel
• iPad Holder
• Handrail
• Running Belt
• End Cap
• Knob (for folding/unfolding)

Accessories included:

• Safety Key
• Screws
• T-wrench
• Knob (to fold and unfold)
• Socket Wrench (for maintenance)

[Diagram description: An illustration shows the treadmill with labels pointing to the Display Panel, iPad Holder, Handrail, Running Belt, and End Cap. Separate illustrations show the accessories: Safety Key, Screws, T-wrench, Knob, and Socket Wrench.]

IV. ASSEMBLY INSTRUCTIONS

[Diagram description: An illustration shows the initial steps of assembling the treadmill. It depicts unfolding the handlebars and attaching them to the main console using a knob and screws with a wrench.]

To assemble the treadmill:

1. Take the knob from the accessories bag.
2. Unfold the handlebars.
3. Screw the knob into the fixing hole until it is tight.
4. Tighten the bracket to the back of the main controller using the screws and wrench.

[Diagram description: An illustration shows how to secure the upright arm if it shakes. It involves removing a cap, inserting a socket wrench and Allen key into holes, tightening, and replacing the cap.]

If the column shakes:

1. Remove the cap on one side of the upright arm.
2. Insert the socket wrench into the corresponding hole of the column.
3. Insert the Allen key into the hole of the tool (socket wrench).
4. Rotate the wrench to tighten.
5. Remove the Allen key and socket wrench after tightening.
6. Close the cap.

V. UNFOLDING/FOLDING INSTRUCTIONS

UNFOLDING THE MACHINE

[Diagram description: An illustration shows the treadmill in its folded state, with arrows indicating the unfolding process. It shows raising a wrench at the bottom of the frame, unfolding the armrest, and tightening a locknut.]

1. Raise the wrench on the bottom of the machine frame to unfold the product.
2. Unfold the armrest.
3. Tighten the locknut behind the control panel. (The lock nut does not have to be completely unscrewed to prevent loss.)

FOLDING THE MACHINE

[Diagram description: An illustration shows the treadmill in its unfolded state, with arrows indicating the folding process. It shows loosening a locknut, folding the armrest, and then loosening a wrench at the bottom of the frame.]

1. Loosen the lock nut behind the control panel.
2. Fold the armrest.
3. Loosen the wrench at the bottom of the product frame to fold the product. (The lock nut does not have to be completely unscrewed to prevent loss.)

VI. CONTROL PANEL

[Diagram description: An image of the treadmill's control panel console, showing buttons and a digital display.]

Before beginning a workout session, ensure that the Safety Key is properly placed onto the Computer Console and the Safety Clip is securely attached to an article of your clothing.

ⓘ NOTE: Always stand on the side rails when you start the treadmill; never start the treadmill while you are standing on the running belt.

FUNCTION BUTTONS

• QUICK START: Press the START button on the computer to begin exercising. The running belt starts moving with an initial speed of 1.0 KPH. You may press the SPEED + or SPEED - button on the computer console to increase or decrease the running speed during exercise. During workout, you may press the STOP button on the computer console to end your workout at any time.
• START: Press the START button to begin exercising.
• STOP: Press the STOP button to end your workout.
• MODE: To select different functions (TIME, DISTANCE, or CALORIES) for setting exercise goals in manual program mode before training.
• PROG (PROGRAM): To select your chosen workout (P1 to P12).

DISPLAY BUTTONS

• SPEED +/-: Use these buttons to adjust the function value up or down, increasing or decreasing running speed adjustments during training periods on different modes.
• TIME: Displays your elapsed workout time in minutes and seconds. You may also pre-set a target time in STOP mode before training. To set TIME, press the MODE button until the TIME window blinks, then use SPEED + or SPEED - to change the setting. The pre-set target time range is from 5:00 to 99:00 minutes. Once set, press START to begin exercising.
• SPEED: Displays the current speed from a minimum of 1.0 KPH to a maximum of 6.0 KPH or 12.0 KPH.
• DIS (DISTANCE): Displays the accumulative distance traveled during your workout. You may also pre-set a target distance in STOP mode. To set DIS, press MODE until the DIS window blinks, then use SPEED + or SPEED - to change the setting. The pre-set target distance range is from 1.00 to 65.0 km. Once set, press START to begin exercising.
• CAL (CALORIES): Displays the total calories burned during your workout. You may also pre-set target calories in STOP mode. To set CAL, press MODE until the CAL window blinks, then use SPEED + or SPEED - to change the setting. The pre-set target calories range is from 10 to 995 calories. Once set, press START to begin exercising.

TRAINING IN PRE-SET PROGRAM MODE:

When in PROGRAM mode, press the PROG (PROGRAM) button to select your chosen workout (P01 to P12). Press the SPEED + or SPEED - button to change the setting. Press the START button to confirm and start your workout. This treadmill console has 2 kinds of Workout Programs to choose from.

UNFOLDED MODE PROGRAM SEQUENCES:

WALKPAD MODE PROGRAM SEQUENCES:

FUNCTION BUTTONS (Walkpad Mode):

• Press the button to start/stop training on different training modes immediately.
• Press the button to select the pre-set training program (P01-P04) mode before training. Hold the button for three seconds to switch on or off the light strips on two sides.
• Press the button to make upward adjustments for the speed.
• Press the button to make backward adjustments for the speed.

VII. MAINTENANCE INSTRUCTIONS

BELT ADJUSTMENT

[Diagram description: An illustration shows the rear of the treadmill with adjustment bolts and a wrench. Arrows indicate turning the bolts clockwise.]

The running belt is pre-adjusted at the factory but may require readjustment after prolonged use due to stretching. To adjust the belt:

1. Turn on the main power switch of the treadmill and let the belt run at a speed of 6-8 KPH.
2. Use the Allen Wrench provided to turn the rear roller adjustment bolts to centre the belt.
3. If the running belt is shifting to the left, turn the left adjustment bolt 1/4 turn clockwise. The belt should start to correct itself.
4. If the running belt is shifting to the right, turn the right adjustment bolt 1/4 turn clockwise. The belt should start to correct itself.
5. Continue turning the adjustment bolts until the running belt is properly centered.

[Diagram description: An illustration shows the rear of the treadmill with adjustment bolts and a wrench, similar to the previous one, indicating adjustment for slipping.]

If the running belt is slipping during use:

1. Turn off and unplug the treadmill.
2. Using the Allen Wrench, turn both left and right rear roller adjustment bolts 1/4 turn clockwise.
3. Turn the main power switch back on and run the treadmill at a speed of 6-8 KPH.
4. Walk on the running belt to determine if the belt is still slipping. Repeat this procedure until the belt no longer slips.

LUBRICATION

Lubricating your treadmill running belt ensures superior performance and extends its life expectancy. When you receive your treadmill, please apply some lubricant into each oil cap. After the first 25 hours of use (or 2-3 months), apply some lubricant and repeat for every following 50 hours of use (or 5-8 months). Run the treadmill at a slow speed for 3 to 5 minutes to evenly distribute lubricant.

HOW TO CHECK RUNNING BELT FOR PROPER LUBRICATION

Remove the cap on the lubrication system and squeeze a few drops of lubricant inside.

• If the surface is slick to the touch, then no further lubrication is required.
• If the surface is dry to the touch, apply some lubricant.

Avoid over-oiling the running deck.

VIII. CARE, MAINTENANCE & TROUBLESHOOTING GUIDE

EMERGENCY STOP

[Diagram description: An illustration shows the treadmill console with the Emergency Stop Key inserted.]

Before beginning a workout session, ensure that the EMERGENCY STOP KEY is placed onto the Computer Console and the Safety Clip is securely attached to an article of your clothing. If you fall, the clip will pull out the EMERGENCY STOP KEY from the Computer Console, and the running belt will stop immediately, helping to prevent injury.

⚠ WARNING: To prevent electrical shock, please turn off and unplug the treadmill before cleaning or performing routine maintenance.

⚠ WARNING: Always check wear and tear components like the foot lock latch tube and running belt to prevent injury.

CLEANING

After each exercise, ensure that the unit is wiped down and any sweat is removed from the unit.

The treadmill can be cleaned with a soft cloth and mild detergent. Do not use abrasives or solvents. Be careful not to get excessive moisture on the display panel, as this might damage the unit and create an electrical hazard.

Please keep the treadmill, especially the computer console, out of direct sunlight to prevent damage to the screen.

STORAGE

Store the treadmill in a clean and dry indoor environment. Never leave or use the unit outdoors. Ensure the master power switch is off and the power cord is unplugged from the wall outlet.

TROUBLESHOOTING GUIDE

IX. EXERCISE GUIDE

ⓘ PLEASE NOTE: Before beginning any exercise program, consult your physician. This is important especially if you are over the age of 45 or individuals with pre-existing health problems.

The pulse sensors are not medical devices. Various factors, including the user's movement, may affect the accuracy of heart rate readings. The pulse sensors are intended only as an exercise aid in determining heart rate trends in general.

Exercising is a great way to control your weight, improve your fitness, and reduce the effect of aging and stress. The key to success is to make exercise a regular and enjoyable part of your everyday life.

The condition of your heart and lungs and how efficiently they deliver oxygen via your blood to your muscles is an important factor to your fitness. Your muscles use this oxygen to provide enough energy for daily activity. This is called aerobic activity. When you are fit, your heart will not have to work so hard. It will pump a lot fewer times per minute, reducing the wear and tear of your heart. So as you can see, the fitter you are, the healthier and greater you will feel.

WARM UP

Start each workout with 5 to 10 minutes of stretching and some light exercises. A proper warm-up increases your body temperature, heart rate, and circulation in preparation for exercise. Ease into your exercise.

After warming up, increase the intensity to your desired exercise program. Be sure to maintain your intensity for maximum performance. Breathe regularly and deeply as you exercise.

COOL DOWN

Finish each workout with a light jog or walk for at least 1 minute. Then complete 5 to 10 minutes of stretching to cool down. This will increase the flexibility of your muscles and will help prevent post-exercise problems.

WORKOUT GUIDELINES

[Diagram description: A line graph showing Heart Rate on the Y-axis (80-200 bpm) against Age on the X-axis (20-75 years). It displays a TARGET ZONE between approximately 70% and 85% of maximum heart rate, a COOL DOWN zone below 70%, and a MAXIMUM zone above 85%.]

This is how your pulse should behave during general fitness exercise. Remember to warm up and cool down for a few minutes.

The most important factor here is the amount of effort you put in. The harder and longer you work, the more calories you will burn.

X. WARRANTY

AUSTRALIAN CONSUMER LAW

Many of LSG's products come with a guarantee or warranty from the manufacturer. In addition, they come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.

You are entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Full details of your consumer rights may be found at www.consumerlaw.gov.au.

Please visit our website to view our full warranty terms and conditions: https://www.lsgfitness.com.au/pages/warranty

WARRANTY AND SUPPORT

Please email LSG Fitness at support@lsgfitness.com.au for all warranty or support issues. For all warranty or support related enquiries, please lodge a support ticket first by sending an email.