KENWOOD Food Processor

Introduction

The KENWOOD food processor and its attachments are designed for a wide range of food preparation tasks, including chopping, cake making, dough preparation, pureeing, mixing, whisking, and grating. This manual provides instructions for safe and effective use of your appliance.

Safety Precautions ⚠️

• Read and keep these instructions for future reference.
• Remove all packaging and labels from the appliance.
• Blades and discs are extremely sharp. Handle with extreme care, especially when fitting, removing, or cleaning. Hold them by the top part, avoiding contact with the cutting edges.
• Do not lift or carry the appliance by the handle, as it may break and cause injury.
• Always remove the knife before filling the bowl.
• Keep fingers and kitchen utensils away from the inside of the bowl or blender when the appliance is connected to the power supply.
• Always switch off the appliance and disconnect it from the power supply before:
  • fitting or removing parts;
  • leaving the appliance unattended;
  • cleaning.
• Never push food down the feed tube with your fingers. Always use the provided pusher.
• Do not fit the knife block to the motor unit without first fitting the blender jug or compact chopper.
• Before removing the lid from the bowl, blender jug, or compact chopper, ensure the appliance is switched off, all moving parts have stopped, and the jug/chopper is not detached from the cutting assembly.
• BURNS RISK: Hot ingredients must cool to room temperature before blending.
• Never use the lid to control the processor; always use the speed selector.
• Handle the locking mechanism with care; excessive force may cause damage or injury.
• Do not use attachments not supplied for this appliance.
• Never leave the appliance unattended when switched on.
• Do not use a damaged appliance. Refer to the 'Servicing and Customer Care' section for repairs.
• Prevent moisture from coming into contact with the motor unit, cord, or plug.
• Ensure the cord does not hang over the edge of a table or touch hot surfaces.
• Do not overload the appliance beyond the recommended speed settings.
• This appliance is not intended for use by children. Keep it and its cord out of reach of children.
• Children should be supervised and not play with the appliance.
• Persons with reduced physical, sensory, or mental capabilities, or lack of experience or knowledge, may use the appliance if supervised or instructed on safe use and understand the associated risks.
• This appliance is for household use only. Kenwood is not responsible for misuse or use contrary to these instructions.
• Improper use can lead to injury.
• Maximum energy consumption is indicated for the most power-hungry attachment. Other attachments may consume less energy.
• Instructions for safe use of each attachment are in the 'Using Attachments' section.

Appliance Components

Main Food Processor Unit

• ⚙️ 1: Motor unit
• ⚙️ 2: Removable drive shaft
• ? 3: Tritan™ bowl
• ? 4: Tritan™ lid
• ➡️ 5: Wide feed tube
• ? 6: Pushers
• ? 7: Safety interlock
• ? 8: Cord storage (rear)
• ? 9: Power on indicator
• ▶️ 10: Auto button
• ⚙️ 11: Speed/Pulse control

Weighing Function (Type FPM91)

• ⚖️ 12: kg/lb button
• ?️ 13: Display screen
• ? 14: ON/ZERO button
• ?️ 15: Weighing plate

Thermo-Resistant Blender

• ? 16: Filter lid
• ? 17: Lid
• ? 18: Blender jug
• ⭕ 19: Sealing ring
• ? 20: Knife block
• ? 21: Spout cap openings

A – Standard Attachments

• ? 22: Knife
• ? 23: Dough tool
• ? 24: Twin whisk
• ? 25: Stirring tool
• ? 26: Max volume disc
• ? 27: Slicing disc - 4mm
• ? 28: Slicing disc - 2mm
• ? 29: Grating disc - 4mm
• ? 30: Grating disc - 2mm
• ? 31: Attachment storage box

B – Optional Attachments

Not all attachments are included with every food processor model. The set of attachments depends on the model. For more information or to order additional attachments, refer to the 'Servicing and Customer Care' section.

• ? 32: Extra fine grating disc (if included)
• ? 33: Julienne disc (if included)
• ? 34: Decorative slicing disc (if included)
• ? 35: French fry disc (if included)
• ? 36: Mini bowl and knife (if included)
• ⚙️ 37: Compact chopper (if included)
• ? 38: Citrus press (if included)
• ? 39: Metal centrifugal juicer (if included)

How to Use the Food Processor

1. Insert the removable drive shaft into the motor unit 1 and press down gently until it is firmly in place.
2. Place the bowl onto the motor unit. Turn the handle back to the right and then clockwise 2 until it clicks into place.
3. Fit the attachment onto the bowl's drive shaft. Note: Always fit the bowl and attachment before adding ingredients.
4. Fit the lid 3 so that the top of the drive is centered over the lid.
5. Insert the pusher into the feed tube. Turn the small pusher clockwise to lock it into the correct position 4. Important: The processor will not operate if the bowl, lid, or wide feed tube are not correctly fitted. The feed tube and bowl handle should be on the right side.
6. Connect the appliance to the power supply. The power on indicator will light up and flash until the bowl and lid are correctly fitted. Select one of the following options:
   • Auto Button: The indicator will light up when the Auto button is pressed, and the optimal speed will be automatically selected for the attachment.
   • Speed Control: Manually select the desired speed (refer to the speed chart).
   • Pulse Mode: Use the pulse mode (P) for intermittent bursts. The motor runs as long as the button is pressed.
7. When processing is complete, turn the speed selector to 'O' (off). If you used the Auto button, press it again and the indicator will extinguish.

Power On Indicator Behaviour

• The power indicator will flash if the lid, bowl, or wide feed tube are not fitted correctly.
• If 'Auto' mode was selected but the interlocks are not engaged, the power and 'Auto' indicators will flash.
• The Auto button will not work if a speed is selected on the speed dial.
• Always switch off the appliance and disconnect it from the power supply before removing the lid.

Important Notes

• The food processor cannot be used for grinding coffee beans or making icing sugar from granulated sugar.

Eco Function

If the food processor is left switched on for 30 minutes without use, it will enter standby mode to reduce energy consumption.

• The power indicator will flash slowly. To exit standby mode, perform one of the following actions:
  • Press the Auto button.
  • Select a speed on the speed dial, then return it to the 'O' position.

When the appliance is ready for use, the power indicator will light up continuously.

Note: If the bowl or lid are fitted incorrectly, the power indicator will flash faster than in Eco mode.

Weighing Function (Type FPM91)

Your food processor has a built-in weighing function to weigh ingredients directly in the food processor bowl or blender jug. The maximum total weight is 3 kg (6.6 lbs).

Weighing Procedure

1. Always fit the removable drive shaft, bowl, and attachment or blender jug to the motor unit before adding ingredients.
2. Connect the appliance to the power supply. The display screen will not be lit.
3. Press the ON/ZERO button once and the display screen will light up.
4. Press the kg/lb button to select the weighing scale in grams or ounces. On first use, the scale defaults to kg/g.
5. Ensure the display shows '0'. If not, use the ON/ZERO button to set it to zero. Then weigh the required ingredients directly in the food processor bowl or blender. Once the weight appears on the screen, press ON/ZERO again and the display will show '0'. Add the next ingredients, and their weight will be shown. Repeat this process until all ingredients are weighed.
6. If the zero reading is not displayed, or if the bowl/attachment/lid is removed, the display will show '----', indicating no reading. Press the ON/ZERO button to set a zero reading.
7. Fit the lid and select the appliance's speed. The display will show '----' during operation until the speed is returned to 'O'.
8. After stopping the appliance, the display will show the last weight value before the speed was set to 'O'. Note: This value includes the weight of the lid if the zero reading was not taken before switching on.
9. The weight of ingredients added via the feed tube during operation will not be reflected on the display.

Weighing Plate (15)

The removable weighing plate is designed for weighing ingredients without using the food processor bowl or blender jug. To use the plate, place it on the motor unit. Then follow steps 2-5 of the 'Weighing Procedure'. To remove the plate, simply lift it off.

Auto Shut-off

• If the same weight is displayed for 5 minutes, the display will automatically turn off.
• The display can be manually turned off by pressing and holding the ON/ZERO button for several seconds.

• Do not overload the appliance beyond the 3 kg maximum weight. If the display shows '[0 - Ld]', the maximum weight has been exceeded.
• Handle the motor unit with care to avoid damaging the weight sensor.
• The appliance must be placed on a dry, level surface before weighing.
• Do not move the motor unit during weighing.

How to Use the Thermo-Resistant Blender

1. Insert the sealing ring 19 into the knife block 20, ensuring it is correctly seated in the corresponding grooves. If the seal is missing or fitted incorrectly, leaks will occur.
2. Hold the knife block 20 by the rear, and insert it into the bowl. Turn counter-clockwise until it clicks into place 6. Refer to the diagrams on the reverse of the knife block for:
   • Unlocked position
   • Locked position
   Note: The blender will not operate if not assembled correctly.
3. Add ingredients to the bowl.
4. Fit the lid onto the bowl and press down to lock it in place 6. Fit the spout cap.
5. Place the blender onto the motor unit and turn clockwise to lock it in place 7. Note: If the blender is not locked correctly, the appliance will not operate.
6. Press the Auto button or select a speed on the dial (see speed chart) or use the pulse mode.

Helpful Tips

• When making mayonnaise, add all ingredients except the oil to the blender. Remove the spout cap. Then, with the appliance running, slowly pour the oil through the lid opening.
• Thick mixtures, such as pâtés or sauces, may stick. If mixtures do not blend well, add more liquid.
• For crushing ice, use the pulse mode for short, intermittent bursts until the ice is crushed to the desired consistency.
• Cover the opening with your hand. For best results, empty the bowl regularly. Blending spices is not recommended as they may damage plastic parts.
• If the blender is not fitted correctly, the appliance will not operate.
• For dry ingredients, cut them into pieces, remove the spout cap, and add pieces one by one while the appliance is running. Cover the opening with your hand. For best results, empty the bowl regularly.
• Do not use the blender as a storage container. Empty it before and after use.
• Never blend more than 1.6 L; for frothy mixtures like milkshakes, this amount should be less.

Recommended Speeds and Processing Times

* Speed is a recommendation and will depend on your recipe and the products being processed.

Using Attachments

22 Knife

The knife is the most versatile of all attachments. The processing time determines the final texture. For a coarse texture, use the pulse mode. Use the knife for making pies and dough, chopping raw and cooked meat, slicing vegetables, nuts, pâtés, dressings, puréed soups, and crumbles from biscuits and bread.

Tips

• Chop meat, bread, vegetables, and similar ingredients into 2 cm cubes before processing.
• Biscuits should be crumbled and added through the feed tube while the processor is running.
• Fat for pastry should be cut into 2 cm cubes while cold.
• Avoid over-processing ingredients.

23 Dough Tool

Used for yeast dough.

• Place dry ingredients in the bowl and add liquid through the feed tube while the appliance is running. Continue until a smooth, elastic dough ball is formed, which usually takes about 60 seconds.
• Re-knead by hand only. Re-kneading in the bowl is not recommended as it may lead to unstable processor operation.

24 Twin Whisk

Used for light mixtures such as egg whites, cream, condensed milk, and for whisking eggs and sugar for sponge cakes. Heavier mixtures, such as those based on fat and flour, will damage the attachment.

Using the Whisk

1. Fit the removable drive shaft and bowl onto the motor unit.
2. Insert each whisk 3 fully into the drive head.
3. Fit the whisk assembly by carefully rotating it until it lowers onto the drive shaft.
4. Add the required ingredients.
5. Fit the lid, ensuring the end of the shaft is centered over the lid.
6. Switch on the food processor.

Important Information

• This whisk is not suitable for processing universal mixes as they are too thick and may damage the attachment. Use the knife for these purposes.

Helpful Tips

• For optimal results, eggs should be at room temperature.
• Ensure the bowl and whisks are clean and free from grease before whisking.
• Heavier ingredients such as flour and dried fruit should be incorporated by hand.
• Do not exceed the maximum load or processing time indicated in the recommendation chart.

25 Mixing Tool

Use this attachment for mixing light ingredients into thick mixtures, such as meringue, mousses, and fruit purées.

1. Fit the removable drive shaft and bowl onto the motor unit.
2. Insert the spatula into the drive head until it is fully seated.
3. Fit the mixing tool by carefully rotating the drive head until it drops onto the drive.
4. Add ingredients.
5. Fit the lid, ensuring the end of the drive is centered over the lid.
6. Select a low speed (1-2).

To Remove the Whisk

Remove the whisk from the drive head by pressing the release button 10.

Tip

• Do not use Auto mode or high speed, as low speed is required for proper mixing.
• For best results, do not whip egg whites or cream to a very stiff peak; the mixing tool cannot cope with such thick mixtures.
• Do not mix ingredients for longer than recommended in the chart, or the mixture may lose its airiness and become slack.
• Any ingredients remaining on the attachment or bowl sides should be carefully mixed in with a spatula.

26 Max Volume Disc

When blending liquids, the max volume disc can be used with the knife. It allows for an increase in the volume of liquid processed from 1.4 to 2 litres, preventing spills and improving slicing results.

1. Fit the removable drive shaft and bowl onto the motor unit.
2. Fit the knife.
3. Add the required ingredients.
4. Place the disc over the knife, ensuring it fits into the grooves inside the bowl 11. Do not press down on the disc.
5. Fit the bowl lid and switch on the appliance.

Discs for Slicing/Grating

Slicing Discs - 4mm (27), 2mm (28)

Use the slicing side for cheese, carrots, potatoes, cabbage, cucumbers, courgettes, beetroot, and onions. Use the grating side for grating cheese, carrots, potatoes, and similar products.

Grating Discs - 4mm (29), 2mm (30)

Use the grating side for grating cheese, carrots, potatoes, and similar products.

Extra Fine Grating Disc 32 (if included)

Used for grating Parmesan cheese and potatoes for potato dumplings.

Julienne Disc 33 (if included)

Used for slicing ingredients into strips or coarse grating, for ingredients for fritters and vegetable garnishes.

Decorative Slicing Disc 34 (if included)

Used for creating decorative shapes when slicing potatoes, carrots, cucumbers, and similar products.

French Fry Disc 35 (if included)

Used for slicing potatoes into strips (French fries), and for ingredients for salads, gratins, and sauces (e.g., cucumbers, apples, and pears).

Safety Precautions

• Never remove the lid until the cutting disc has stopped rotating completely.
• Cutting discs are extremely sharp and require extreme care.
• Do not overfill the bowl – do not exceed the maximum capacity indicated on the bowl.

Using the Cutting Discs

1. Fit the removable drive shaft and bowl onto the motor unit.
2. Using the central handle, fit the disc onto the drive shaft with the correct side facing up 12.
3. Fit the lid.
4. Place the food into the feed tube. Select the appropriate feed tube size. The pusher has a smaller diameter feed tube for individual pieces or thin ingredients. To use the smaller feed tube, insert the larger pusher into the smaller feed tube. To use the larger feed tube, insert the smaller pusher into the larger pusher and turn clockwise to lock. Do not fill the feed tube above the maximum level – the processor will not operate if the wide feed tube is not fitted correctly.
5. Switch on and gently push the food down with the pusher; never put your fingers into the feed tube.

Tips

• Use fresh ingredients.
• Do not cut ingredients too finely. Fill the wide feed tube evenly across its width. This prevents ingredients from shifting during processing. You can also use the smaller feed tube.
• When using the julienne disc, place ingredients horizontally.
• When slicing or grating: ingredients placed vertically 13 will be shorter than those placed horizontally 14.
• Ingredients placed vertically will be cut into shorter pieces than those placed horizontally.
• A small amount of product will always remain on the disc or in the bowl after processing.

36 Mini Bowl and Knife (if included)

The mini bowl is used for chopping herbs and processing small quantities of ingredients such as meat, onions, nuts, mayonnaise, vegetables, purées, sauces, and baby food. Do not overfill the bowl.

• a Mini knife
• b Mini bowl

Using the Mini Bowl and Knife

1. Fit the removable drive shaft and bowl onto the motor unit.
2. Place the mini bowl onto the removable drive shaft, aligning the cut-out section with the corresponding protrusions 15 on the main bowl. Note: If the mini bowl is not fitted correctly, you will not be able to close the main bowl lid.
3. Fit the knife onto the drive shaft 16.
4. Add the ingredients to be processed.
5. Fit the lid and switch on the food processor.

Safety Precautions

• Never remove the lid until the knife has stopped rotating completely.
• Knife blades are very sharp. Handle with care.

Important Information

• This appliance is not intended for grinding spices, as they may damage the plastic surfaces of the appliance.
• The appliance is also not intended for grinding hard products such as coffee beans, ice cubes, or chocolate, as they may damage the knife.

Tips

• Herbs to be chopped should be clean and dry.
• When mixing cooked ingredients for baby food, add a little liquid.
• Products such as meat, bread, and vegetables should be cut into approximately 1-2 cm cubes before processing.
• When making mayonnaise, pour the oil through the feed tube.

37 Compact Chopper (if included)

Use the compact chopper for processing dry ingredients such as nuts, coffee beans; it is also suitable for grinding various spices such as: peppercorns, cardamom seeds, coriander, fennel, fresh ginger root, fresh chilli peppers, and whole garlic cloves.

• a Sealing ring
• b Knife block
• c Glass jar

Using the Compact Chopper

1. Add ingredients to the jar. The jar should be half-filled.
2. Fit the sealing ring onto the knife block.
3. Holding the knife block, insert the knives into the jar and turn counter-clockwise to lock 17.
4. Fit the compact chopper onto the motor unit and turn clockwise to lock it in place 18.
5. Use the 'Auto' button or select the required speed (see recommended speeds chart) or use the pulse control.

Safety Precautions

• Never fit the knife block to the appliance without the jar attached.
• Never unscrew the jar while the compact chopper is fitted to the appliance.
• Do not touch the sharp edges of the knives. Keep the knife block out of reach of children.
• Never remove the compact chopper until the knives have stopped rotating completely.
• To prolong the life of your compact chopper, do not use it continuously for longer than 60 seconds. Switch off once the desired consistency is reached.
• The appliance will not operate if the compact chopper is not fitted correctly.
• Do not use the compact chopper for grinding ginger root, as it is too hard and may damage the knives.

Helpful Tips

• For optimal spice grinding, it is recommended not to process more than 100 g at a time in the compact chopper.

38 Citrus Press (if included)

This citrus press is used for extracting juice from citrus fruits (e.g., oranges, lemons, limes, and grapefruits).

• a Cone
• b Sieve

Using the Citrus Press

1. Fit the removable drive shaft and bowl onto the motor unit.
2. Place the sieve into the bowl, ensuring the sieve handle is positioned directly over the bowl handle 19.
3. Place the cone over the drive shaft and turn until it is fully seated 20.
4. Cut the fruit in half. Then switch on the appliance and press the cut side of the fruit onto the cone.
5. If the sieve locks are not engaged, the citrus press will not operate. For optimal results, store fruits at room temperature and roll them on the work surface before juicing. To improve juicing, rotate the fruit on the cone from side to side. For large quantities, clean the sieve regularly to prevent seeds and peel from accumulating.

39 Metal Centrifugal Juicer (if included)

The centrifugal juicer allows you to extract juice from hard fruits and vegetables.

• a Pusher
• b Lid
• c Pulp extractor
• d Filter basket
• e Bowl
• f Juice spout
• g Juicer and drive adapter

Using the Metal Centrifugal Juicer

1. Fit the drive adapter onto the motor unit 21, pressing down gently to ensure it is correctly fitted.
2. Then fit the bowl. Turn the handle back and turn clockwise to lock 22.
3. Insert the pulp extractor into the filter basket, ensuring the tabs engage with the slots in the base of the basket 23.
4. Fit the filter basket 24.
5. Fit the attachment lid onto the bowl and turn to lock, ensuring the feed tube is positioned over the lid. The juicer will not operate if the bowl or lid are not correctly fitted to the locking mechanism.
6. Place a glass or other container under the juice spout.
7. Cut the products so they can pass through the feed tube.
8. Select the 'auto' mode and gently push the products down with the pusher. Never put your fingers into the feed tube. Process the loaded portion completely before adding more.
9. After feeding the last piece, let the juicer run for another 30 seconds to extract any remaining juice from the filter basket.

Safety Precautions

• Do not use the juicer if the filter is damaged.
• Only use the provided pusher. Never insert fingers into the feed tube. Before cleaning the feed tube, unplug the appliance.
• Before removing the lid, switch off the juicer and wait for the filter to stop.

Important Information

• If the juicer starts to vibrate, switch it off and empty the pulp from the basket. (The juicer vibrates when the pulp is unevenly distributed in the basket).
• You can process no more than 1 kg of fruits or vegetables at a time (see recommended speeds chart).

Cleaning and Care

General

• If products are too hard, the juicer may slow down or stop completely. Switch off the appliance and empty the filter.
• Regularly unplug the appliance and clean the pulp collector during use.

Tips

• Before processing, remove stones and seeds (e.g., from peppers, melons, plums) and tough skins (e.g., from melons, pineapples). Apples and pears do not need peeling or coring.
• Use firm, fresh fruits and vegetables.
• For maximum juice yield, load small portions of produce into the feed tube and push down slowly during processing.
• Citrus fruits – peel and remove the white pith, otherwise the juice may be bitter. For best results, use the citrus press.

31 Securing the Storage Box

The food processor is equipped with a storage box for attachments and discs.

1. When not in use, store attachments and discs in the storage box 20.
2. The box has a lock that clicks shut when you close the lid. To open the lid, press the tab 27 and lift the lid 28.

Care and Cleaning

• Always switch off and disconnect the appliance from the power supply before cleaning.
• Discs and knives are very sharp and require extreme care.
• Some products may discolour plastic parts. This is normal, does not damage the parts, and does not affect the taste of the food. To remove discoloured stains, rub with a cloth dampened with vegetable oil.

Motor Unit

• Wipe with a damp cloth, then dry. Ensure the area around the locking mechanism is free from food residue.
• Do not immerse the motor unit in water.
• The power cord can be shortened if necessary by storing part of it in the storage compartment at the rear of the drive unit 29.

Blender and Compact Chopper

1. Empty the jugs/chopper, unscrew the knife block by turning it to the unlocked position to release.
2. Wash jugs/choppers by hand.
3. Remove and wash the sealing rings.
4. Do not touch the sharp knives; wash them with a brush under hot soapy water, then rinse thoroughly under the tap. Do not immerse the knife block in water.
5. Turn them upside down and leave to dry.

Twin Whisk

• Remove whisks from the drive head by pulling gently. Wash in hot, soapy water.
• Wipe the drive head with a damp cloth, then dry. Do not immerse the drive head in water.

Mixing Tool

• Remove the spatula from the drive head by pressing the release button 11. Wash in hot, soapy water.
• Wipe the drive head with a damp cloth, then dry. Do not immerse the drive head in water.

Centrifugal Juicer

• The cutting blades at the base of the filter basket are very sharp, so handle the basket and blades with extreme care during use and cleaning.
• Some products may discolour plastic parts. This is normal, does not damage the parts, and does not affect the taste of the food. To remove discoloured stains, rub with a cloth dampened with vegetable oil.

Juicer Drive Adapter

• Wipe with a damp cloth, then dry.
• Do not immerse the adapter in water.

Other Parts

Wash by hand and then dry. Some parts are dishwasher safe, but should only be placed on the top rack. Do not place parts directly above the heating element on the lower rack. Use a short program with a low temperature (max. 50°C).

Servicing and Customer Care

If the cord is damaged, it must be replaced by the manufacturer or its service agent to avoid a hazard.

Before returning the appliance for servicing, check the 'Troubleshooting' section. If you need assistance with:

• Using the appliance
• Servicing or repair
• Contact the retailer where you purchased the appliance.

Date code information may be found on the underside of the product or near the technical data plate. The date code is shown as a year and month code, followed by the week number. NOTE: The first two digits indicate the year, the last two digits the sequential week number of the year. For example: 1st September 2013 = 13L35.

• Designed and engineered by Kenwood, United Kingdom.
• Made in China.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THIS PRODUCT ACCORDING TO THE WEEE DIRECTIVE 2002/96/EC.

At the end of its working life, this product must not be disposed of with ordinary household waste. It must be taken to a special collection centre for recycling electrical and electronic appliances. The crossed-out wheelie bin symbol on the product, accessories, or packaging indicates that this product must not be treated as normal household waste. It is the user's responsibility to dispose of this product and other electrical and electronic appliances via a designated collection point in their locality. For further information regarding collection and recycling, please contact your local authority or the retailer where you purchased this product. Disposal in accordance with this directive will help prevent potential negative consequences for the environment and human health.

Manufacturer's Address: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH, UK

Importer's Address: OOO 'Delongi', Russia, 127055, Moscow, ul. Sushchevskaya, d. 27, str. 3. Tel.: +7 (495) 781-26-76

Troubleshooting

Troubleshooting (Continued)

Maintenance and Care

General

• If the cord is damaged, it must be replaced by KENWOOD or an authorised repair workshop to avoid a hazard.
• If the appliance malfunctions during use, consult the 'Troubleshooting' section before contacting customer service.
• For assistance with:
  • using the appliance
  • servicing or repair
  Contact the retailer where you purchased the appliance.

Date code information may be found on the underside of the product or near the technical data plate. The date code is shown as a year and month code, followed by the week number. NOTE: The first two digits indicate the year, the last two digits the sequential week number of the year. For example: 1st September 2013 = 13L35.

• Designed and engineered by Kenwood, United Kingdom.
• Made in China.

Technical Specifications

Manufacturer and Importer Information

Manufacturer's Address: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH, UK

Importer's Address: OOO 'Delongi', Russia, 127055, Moscow, ul. Sushchevskaya, d. 27, str. 3. Tel.: +7 (495) 781-26-76

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THIS PRODUCT ACCORDING TO THE WEEE DIRECTIVE 2002/96/EC.

At the end of its working life, this product must not be disposed of with ordinary household waste. It must be taken to a special collection centre for recycling electrical and electronic appliances. The crossed-out wheelie bin symbol on the product, accessories, or packaging indicates that this product must not be treated as normal household waste. It is the user's responsibility to dispose of this product and other electrical and electronic appliances via a designated collection point in their locality. For further information regarding collection and recycling, please contact your local authority or the retailer where you purchased this product. Disposal in accordance with this directive will help prevent potential negative consequences for the environment and human health.