Somfy Smart Shading Standalone Commissioning

Summary

This guide provides instructions for commissioning Somfy Smart Shading products, including Ysia control, TaHoma switch setup, and motor configuration.

Smart Shading Motors

• Motor LED behaviours
• Motor program button

Ysia Control

• Navigating the Ysia control
• Controlling a motor or group with Ysia
• Ysia control LED behaviours
• Ysia control battery compartment

Smart Shading Commissioning

• Considerations for Smart Shading commissioning

Setting Motor End Limits

• Setting motor limits and binding the Ysia control
• Setting motor limits and detaching the Ysia control
• Setting motor end limits process flowchart

Binding an Ysia Control

• Binding an Ysia control to a motor with existing end limits
• Binding an Ysia control process flowchart

Adjusting Motor Settings

• Adjusting motor end limits
• Adjusting motor rotation
• Adjusting motor settings process flowchart

Setting the 'my' Favourite Position on a Motor

• Setting the 'my' favourite position flow chart

Setting a Group Channel(s)

• Copy/paste motors to a group channel
• Copy/paste motors to a group channel process flow
• Pairing 2 or more motors to an Ysia 1 control
• Pairing 2 or more motors to an Ysia 1 control process flow

Setting Curtain End Limits

• Setting end limits on a Glydea Ultra + Zigbee module and binding an Ysia control
• Setting end limits on a Glydea Ultra + Zigbee module process flowchart
• Adding a Glydea Zigbee module to a Glydea RTS curtain motor with existing end limits and then binding an Ysia control
• Adding a Glydea Zigbee module to a Glydea RTS curtain motor with existing end limits and then binding an Ysia control process flowchart

TaHoma switch & Zigbee

• TaHoma switch & mesh network set-up considerations
• Navigating the TaHoma by Somfy application

TaHoma switch Set Up

• Launch TaHoma by Somfy application and create a profile
• Connect the TaHoma switch to power
• Connect the TaHoma switch to the internet
• Create a TaHoma account or log in
• Adding Smart Shading actuators
• Adding Ysia controls
• Binding Ysia controls to Smart Shading equipment
• Setting up the scenario launchers on the top of the hub
• Troubleshooting tips when pairing Smart Shading equipment to a TaHoma switch

Smart Shading Equipment

• Steps to factory reset Smart Shading equipment

Smart Shading Motors

LED Behaviours

Program Button

Press and hold the program button:

• 1 Jog: Motor is in programming mode.
• 2 Jogs: Motor is detached from a mesh network; programmed end limits remain; motor is in discovery mode.
• 3 Jogs: Motor is factory reset.
• 4 Jogs: Motor software will restart (please allow up to 5 minutes for the restart to complete).

WARNING: If the program button on the motor head is held for more than 20 seconds, the motor will go into recovery mode and cannot be recovered or used.

Ysia Control

Navigating the Ysia Control

The Ysia control features the following buttons:

• UP Button: Used to raise, open or tilt.
• MY/STOP Button: Used to stop motor movement or move to previously saved 'my' position.
• DOWN Button: Used to lower, close, or tilt.
• Channel Selection Button: To select channel.

The control also has indicators:

• Status LED Indicator: Shows commands and Zigbee network activity.
• Channel LED Indicator: Shows the selected channel.

The wall bracket mounting area includes the product label and QR code. The programming button is used to pair and reset products.

Controlling a Motor or Group with Ysia

UP Button:

• Short Press: Sends motor to the upper limit/open position.
• Long Press: Moves tilting motors up, release to stop.

NOTE: PRESS & HOLD for desired length of travel.

MY/STOP Button:

• Single Press: Stops the motor during movement.
• Quick Double Press: Moves motor to 'my' position.

DOWN Button:

• Short Press: Sends motor to the lower limit/closed position.
• Long Press: Moves tilting motors down, release to stop.

NOTE: PRESS & HOLD for desired length of travel.

Smart Shading Ysia Control LED Behaviours

Ysia Control Battery Compartment

Diagrams show the battery compartments for Ysia 1 [1871153], Ysia 5 [1871154], and Ysia 5 Variation [1871281].

Smart Shading Commissioning

Considerations for Smart Shading Commissioning

This table outlines commissioning actions for Standalone (Motor & Ysia Control Only) and TaHoma pro App setups:

Notes:

• All Somfy Smart Shading tubular motors require a motor plate (sold separately). Refer to somfypro.com.au for details.
• Zigbee 3.0 radio range is 7m (in room). In standalone, motors and Ysia control have a direct connection. A mesh network is created with a main controller (e.g., TaHoma switch).
• In a standalone setup, the Ysia remote control cannot be paired with third-party Zigbee 3.0 equipment. A TaHoma switch hub is required for this.
• Apple HomeKit compatibility is achievable with a TaHoma switch hub only.
• For standalone commissioning, ensure the motor and Ysia control are within 60cm of each other for ideal pairing.
• Do not rush the process. Observe the LEDs on the remote, motor, and jogs to validate setup.
• Allow up to 15 seconds for the process to complete before testing control.

Setting Motor End Limits

Setting the Motor Limits and Binding the Ysia Control

Pre-start checklist:

• Ensure the motor and Ysia control are factory reset.
• For ideal pairing, ensure the motor and Ysia control are within 60cm of each other (over 1.5m may impact pairing).
• Do not rush the process. Observe LEDs and jogs for validation.
• If issues occur, reset both motor and control and restart.
• For AC motors, ensure the motor is plugged in. For WireFree motors, ensure the motor is fully charged.

1. Select the channel on the control: When using a multichannel Ysia control, select the desired channel before programming. For Ysia 1 Channel, proceed to step 2.
2. Wake up the motor: Press and hold the Program button (approx. 3-5 seconds) on the motor head until it jogs once. The motor head LED will flash orange.
3. Put the Ysia into pairing mode: Ensure Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) UP & DOWN on the Ysia control and wait. The LED on the control will flash orange. This may take up to 30 seconds. Do not touch or intervene during this time.
4. Ysia control is successfully paired: When pairing is successful, the LED on the control will illuminate green. Around 10 seconds later, the motor will jog once.
5. Check/change the motor rotation: The Ysia control LED will flash orange. Press and hold UP or DOWN on the Ysia control to check motor direction. If correct, proceed. If incorrect, press and hold 'my' until the motor jogs once.
6. Set the upper limit: Press and hold the UP button until the preferred upper limit is reached. Briefly press (less than 0.5 seconds) 'my' and DOWN to set the upper limit. The motor will jog once.
7. Set the lower limit: Press and hold the DOWN button until the preferred lower limit is reached. Briefly press (less than 0.5 seconds) 'my' and UP to set the lower limit. The motor will jog once.
8. Bind the Ysia control to the motor: Briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control. The motor will jog once. The LED on the motor and Ysia control will turn off.

Setting the Motor Limits and Detaching the Ysia Control

Pre-start checklist:

• Ensure the motor and Ysia control are factory reset.
• For ideal pairing, ensure the motor and Ysia control are within 60cm of each other (over 1.5m may impact pairing).
• Do not rush the process. Observe LEDs and jogs for validation.
• If issues occur, reset both motor and control and restart.
• For AC motors, ensure the motor is plugged in. For WireFree motors, ensure the motor is fully charged.

1. Select the channel on the control: When using a multichannel Ysia control, select the desired channel before programming. For Ysia 1 Channel, proceed to step 2.
2. Wake up the motor: Press and hold the Program button (approx. 3-5 seconds) on the motor head until it jogs once. The motor head LED will flash orange.
3. Put the Ysia into pairing mode: Ensure Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) UP & DOWN on the Ysia control and wait. The LED on the control will flash orange. This may take up to 30 seconds. Do not touch or intervene during this time.
4. Ysia control is successfully paired: When pairing is successful, the LED on the control will illuminate green. Around 10 seconds later, the motor will jog once.
5. Check/change the motor rotation: The Ysia control LED will flash orange. Press and hold UP or DOWN on the Ysia control to check motor direction. If correct, proceed. If incorrect, press and hold 'my' until the motor jogs once.
6. Set the upper limit: Press and hold the UP button until the preferred upper limit is reached. Briefly press (less than 0.5 seconds) 'my' and DOWN to set the upper limit. The motor will jog once.
7. Set the lower limit: Press and hold the DOWN button until the preferred lower limit is reached. Briefly press (less than 0.5 seconds) 'my' and UP to set the lower limit. The motor will jog once.
8. Detach the Ysia control from the motor: Press and hold the UP and DOWN commands on the control. The LED on the control will flash green, then solid green, then turn off. The motor LED will flash orange but then turn off.

Flowchart for Setting Motor End Limits: A flowchart visually guides the user through resetting the motor, selecting the channel, waking the motor, pairing the Ysia control, checking motor direction, setting upper and lower limits, and binding the control.

Binding an Ysia Control

Binding an Ysia Control to a Motor with Existing End Limits

Pre-start checklist:

• Ensure the individual motor(s) end limits are set.
• Ensure there is no Ysia control bound to the motor. Reset the Ysia control before commencing. Refer to page 40 for reset instructions.

1. Select the channel on the control: When using a multichannel Ysia control, select the desired channel before programming. For Ysia 1 Channel, proceed to step 2.
2. Wake up the motor: Press and hold the Program button (approx. 3-5 seconds) on the motor head until it jogs once. The motor head LED will flash orange.
3. Put the Ysia into pairing mode: Ensure Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) UP & DOWN on the Ysia control and wait. The LED on the control will flash orange. This may take up to 30 seconds. Do not touch or intervene during this time.
4. Ysia control is successfully paired: When pairing is successful, the LED on the control will illuminate green, then turn off. Around 10 seconds later, the motor will jog once. The LED on the Ysia control will begin to flash orange.
5. Bind the motor to the control: Briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control. The LED on the control will illuminate green. The motor will jog once. The LED on the motor and Ysia control will turn off. Repeat steps for subsequent motor(s) and channels.

Flowchart for Binding an Ysia Control: A flowchart illustrates the process of ensuring the motor is charged, selecting the channel, waking the motor, pairing the Ysia control, and binding the motor to the control.

Adjust Motor End Limits

Adjusting the End Limit(s) to a Motor

Pre-start checklist:

• Ensure the individual motor(s) end limits are set.
• Ensure the Ysia control is bound to the motor.

1. Activate programming mode: Ensure the Ysia control is within 60cm of the motor head. Press and hold the Program button on the Ysia control until the LED sequence GREEN > RED > GREEN is achieved. The motor will jog once.
2. Activate the motor adjustment mode: Ensure the Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) UP & DOWN on the Ysia control and wait. The LED on the control will flash orange. This may take up to 30 seconds. Do not touch or intervene during this time.
3. Ysia & motor are in programming mode: When pairing is successful, the LED on the control will illuminate green. Around 10 seconds later, the motor will jog once. The LED on the Ysia control will flash orange.
4. Check/change the motor rotation: Press and hold UP or DOWN on the Ysia control to check motor direction. If correct, proceed. If incorrect, press and hold 'my' until the motor jogs once.
5. Adjust the end limits: Adjust either the UP and/or DOWN limit as desired.
6. Set the new end limits: To set the upper limit, briefly press (less than 0.5 seconds) DOWN and 'my' on the control. To set the lower limit, briefly press (less than 0.5 seconds) UP and 'my' on the control. The motor will jog once to confirm the limit is set.
7. Saving the new end limits: Once one or both limits are adjusted, briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control to finalize the new end limits and remote binding. The motor will jog once and the LED on the motor and Ysia control will turn off.

Adjust Motor Rotation

Adjusting the Rotation Direction on a Motor with End Limit(s)

Pre-start checklist:

• Ensure the individual motor(s) end limits are set.
• Ensure the Ysia control is bound to the motor.

1. Select the channel on the Ysia control: Using the channel selector button on the multichannel Ysia control, identify the desired motor. If using Ysia 1 channel, move to step 2.
2. Activate programming mode: Ensure the Ysia control is within 60cm of the motor head. Press and hold the Program button on the Ysia control until the LED sequence GREEN > RED > GREEN is achieved. The motor will jog once.
3. Activate the motor adjustment mode: Ensure the Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) UP & DOWN on the Ysia control and wait. The LED on the Ysia control will flash orange. This may take up to 30 seconds. Do not touch or intervene during this time.
4. Ysia & motor are in programming mode: When pairing is successful, the LED on the Ysia control will illuminate green. Around 10 seconds later, the motor will jog once. The LED on the Ysia control will flash orange.
5. Change the motor rotation: The Ysia control LED will flash orange. Press and hold the 'my' button until the motor jogs once.
6. Finalise the adjustment and bind the Ysia control: Briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control to finalize the motor rotation and remote binding. The motor will jog once and the LED on the motor and Ysia control will turn off.

'my' Favourite Position

Setting the 'my' Favourite Position on a Motor

Pre-start checklist:

• Ensure the motor is in 'User Mode' meaning limits are set and control is paired.

1. Select the channel on the Ysia control: Select the desired channel before programming. If using Ysia 1 Channel, move to step 2.
2. Send motor to desired position: Using UP or DOWN commands on the Ysia control, move the motor and stop at the desired position.
3. Set the 'my' position: Press and hold 'my' button on the control (approx. 5 secs). The LED on the Ysia control will blink green. Release the 'my' button once the LED has solid green. The motor will jog once.
4. Test 'my' position setting: Using the UP or DOWN command on the Ysia control, send the motor to the preset upper or lower limit. Double press the 'my' button on the Ysia control.

Note: Once set, a 'my' position can be adjusted, but not deleted without factory resetting the motor or using TaHoma pro application.

Group Channel

Copy/paste Motors to a Group Channel Using a Multichannel Ysia

Pre-start checklist:

• Ensure the individual motor limits are set to the individual multichannel Ysia control channels.

1. Select the channel on the Ysia control: Using the channel selector button on the multichannel Ysia control, identify the desired motor.
2. Activate programming mode: Ensure the Ysia control is within 60cm of the motor head. Press and hold the Program button on the Ysia control until the LED sequence GREEN > RED > GREEN is achieved. The motor will jog once.
3. Select the group channel: Select the desired group channel on the Ysia control. This must be different to the channel selected in step 1.
4. Set the group channel: Ensure the Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) the Program button on the Ysia control. The LED on the Ysia control will flash orange, then green. The motor will jog once. Repeat steps, until all individual motors are copied to the group channel.

Pairing 2 or more Motors to an Ysia 1 Channel Control

Pre-start checklist:

• Ensure the individual motor(s) end limits are set.
• Ensure there is no Ysia control bound to the motor. To detach a motor from a remote, press and hold the motor Program button until the motor jogs twice. Ensure the Ysia control is reset before commencing the below steps. Refer to page 40 for instructions on resetting the Ysia control.

1. Wake up the first motor: Press and hold the Program button (approx. 3-5 seconds) on the motor head until it jogs once.
2. Put the Ysia into pairing mode: Ensure Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) UP & DOWN on the Ysia control and wait. The LED on the control will flash orange. This may take up to 30 seconds. Do not touch or intervene during this time.
3. Ysia control is successfully paired: When pairing is successful, the LED on the Ysia control will illuminate green. Around 10 seconds later, the motor will jog once.
4. Bind the Ysia control to the first motor: Briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control. The motor will jog once. The LED on the motor and Ysia control will turn off.
5. Wake up the second motor: Press and hold the Program button (approx. 3-5 seconds) on the motor head until it jogs once.
6. Binding the control: Ensure the Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control. The LED on the Ysia control will flash orange. This may take up to 30 seconds. Do not touch or intervene during this time.
7. Finalise and repeat: The LED on the Ysia control will flash orange, then green. The motor will jog once. Repeat steps 5 – 7, until balance of motors are paired to the same Ysia 1 channel control.

Flowchart for Grouping Motors with Ysia 1: A flowchart details the process for grouping motors, including resetting the motor, waking it up, pairing the Ysia control, and binding it to the motor.

Setting Curtain End Limits

Setting End Limits on a Glydea Ultra + Zigbee Module and Binding an Ysia Control

Pre-start checklist:

• Ensure the Glydea Ultra RTS motor is in factory mode (no limits set/no RTS or Zigbee Ysia control paired).

1. Insert the Glydea Ultra Zigbee Module & power up the motor: Remove the motor cover from the base of the motor. Insert the Glydea Ultra Zigbee module into the slot. Plug the motor into mains power.
2. Mount the motor and power it up: Mount the motor onto the curtain track. Plug the motor into mains power.
3. Self-learning end limits (touch motion method): Gently tug the curtain fabric to manually trigger the touch motion function. The motor will automatically begin to learn its end limits. Do not stop the motor until the end limits have been reached and the motor has completely stopped.
4. Put the motor into discovery mode: Press and hold the S button on the bottom of the motor (Approx. 3-5 seconds) until the motor jogs once. The LED on the motor will flash orange.
5. Put the Ysia control into pairing mode: Ensure the Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control. The LED on the Ysia control will flash orange. This may take up to 30 seconds. Do not touch or intervene during this time.
6. Mount the motor and power it up: When the mesh pairing is successful, the LED on the Ysia control will illuminate green. Around 10 seconds later, the motor will jog once.

Adding a Glydea Zigbee Module to a Glydea Ultra RTS Curtain Motor with Existing End Limits and then Binding an Ysia Control

Pre-start checklist:

• Ensure the Glydea Ultra RTS motor has preset end limits.
• Do not dismount the curtain motor from the track.

1. Insert the Glydea Ultra Zigbee Module and power up the motor: Turn off mains power to the motor. Remove the motor cover from the base of the motor. Insert the Glydea Ultra Zigbee module into the slot. Plug the motor into mains power.
2. Put the motor into discovery mode: Press and hold the S button on the bottom of the motor (Approx. 3-5 seconds) until the motor jogs once. The LED on the motor will flash orange.
3. Put the Ysia control into pairing mode: Ensure the Ysia control is within 60cm of the motor head. Briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control. The LED on the Ysia control will flash orange. This may take up to 1 minute. Do not touch or intervene during this time.
4. Mount the motor and power it up: When the mesh pairing is successful, the LED on the Ysia control will illuminate green. Around 10 seconds later, the motor will jog once.

Note: Any paired RTS controls will no longer operate the curtain motor once the Glydea Ultra Zigbee module is inserted. Please use only the paired Ysia control.

Flowchart for Setting Curtain End Limits: A flowchart illustrates the process of inserting the Zigbee module, mounting the motor, triggering touch motion for self-learning, and putting the motor into discovery mode.

TaHoma switch & Zigbee

TaHoma switch & mesh network set-up considerations

• TaHoma switch [1871147] requires an active, secure internet connection. It can be configured via WiFi or ethernet cable. An ethernet adaptor [9028054] is required for ethernet connection.
• All Smart Shading equipment, including Ysia remote controls, must be paired to the TaHoma switch as individual products. If an Ysia control is bound to a motor, this binding will disconnect upon pairing to the TaHoma switch. Rebind motors to Ysia controls after pairing to the hub.
• All Smart Shading motors must have their end limits set before pairing to a TaHoma switch hub.
• An active email address is required for a TaHoma® switch account, which cannot be the same as an existing Connexoon Window RTS or TaHoma switch account.
• Ensure 3rd party compatible applications are downloaded and set up on your smart device.
• TaHoma by Somfy application equipment favourites are linked to a smart phone or device.
• Have the motor and Ysia control QR code ready for all Smart Shading equipment.
• For a seamless experience, build a strong Zigbee mesh network by pairing wired AC Zigbee motors first, then Philips Hue Smart Plugs, then WireFree Zigbee motors, followed by Ysia controls.
• Somfy recommends a maximum of 6 Smart Shading WireFree motors per 1 Zigbee repeater. For the 7th motor, pair an additional repeater. Trusted repeaters include: Sonesse 40 Zigbee AC, Glydea Ultra AC with Zigbee Module, Izymo Motor or On/Off Receiver, and Philips Hue Smart Plug.
• A Philips Hue Smart Plug can be directly configured to a TaHoma switch hub without the Philips Hue app or bridge.

Navigating the TaHoma by Somfy application

Click the icons on the bottom of the screen to navigate the app:

• My Favourites: A shortcut to most used equipment or personalized scenarios.
• My Home: Control individual or grouped equipment simply and efficiently.
• My Scenes: Simplify and personalize your home with scheduled timers.
• More: Manage your TaHoma account & profile, paired Ysia controls, scenario launchers, and more.

TaHoma switch Set up

Launch the TaHoma by Somfy Application

1. Launch the TaHoma by Somfy application and create a profile:
   1. Search for TaHoma by Somfy in the Apple or Google Play app store.
   2. Download the TaHoma by Somfy app.
   3. Open the app, click 'Start', and select your country.
   4. Select the TaHoma switch hub.
   5. Select 'I do not have a TaHoma account'.
2. Connect the TaHoma switch to power:
   1. Connect the power adaptor to the USB power cable.
   2. Insert the micro-USB into the bottom of the box.
   3. Ensure the power is turned on.
   4. The LED light on the box will illuminate blue. If not blinking blue, follow in-app troubleshooting steps.

Setting up a TaHoma switch hub

1. Connect the TaHoma switch to the internet:
   1. If prompted, enable location and Bluetooth access. Select your 2.4GHz (4G) WiFi.
   2. Enter your WiFi network password. Click 'Next'. Click 'Link my account'.
2. Create a TaHoma account or log in:
   1. Enter a preferred email address to create your Somfy account/log in. Click 'Next'.
   2. Add a password* to secure the account. Click 'Next'.
   3. Enter your name. Click 'Next'.
   4. Accept the Terms & Conditions and select your Somfy communication preferences. Click 'Next'. Click 'Finish'.

*The password must contain at least 8 characters: one capital letter, one lowercase letter, and one number.

The TaHoma switch hub may require a software update. Keep the app open during the update; the hub's LED will flash red while updating.

Adding Smart Shading actuators

1. Select 'Add Equipment'.
2. Follow in-app prompts to select end-product application type.
3. Select 'No remote control is paired yet to the motor'. Select 'Continue'.
4. Follow in-app prompts to add equipment via QR code (Bluetooth) or Zigbee mesh network (discovery mode). Rename and personalize automations.
5. Rename the equipment.
6. Add the equipment to a room.

In the event a Smart Shading motor QR code is not available, the TaHoma by Somfy application will prompt you to put the equipment into pairing mode. Press and hold the Program button on the motor head until it jogs twice. Follow in-app instructions to finalize configuration.

Adding Ysia controls

1. Select 'Add Equipment'.
2. Select 'Remote Control'.
3. Select 'Somfy' brand.
4. Select 'Zigbee remote control'. Select 'Continue'.
5. Follow in-app prompts to add equipment via QR code (Bluetooth) or Zigbee mesh network (discovery mode).
6. Rename the Ysia control.

In the event the Ysia control QR code is not available, the TaHoma by Somfy application will prompt you to put the Ysia control into pairing mode. Press and hold the Program button until the LED sequence GREEN > RED > GREEN > RED is achieved. Follow in-app instructions to finalize configuration.

Binding Ysia Controls to Smart Shading equipment

1. Select the '***' more tab.
2. Select 'My remote controls'.
3. Select the remote control.
4. Select 'Linked devices'.
5. For Ysia 5 Channel, select the channel to bind the equipment to.
6. Select the equipment(s). The identified motor(s) will jog once when selected.
7. Briefly press (less than 0.5 seconds) the Program button on the back of the Ysia control. Select 'Next'. The LED on the Ysia control will flash orange during binding.
8. Once binding is complete, the LED on the Ysia control blinks green, then turns off.

Setting up the scenario launchers on the top of the hub

1. Select the '***' more tab.
2. Select 'Configuration of the installation'.
3. Select 'Box'.
4. Select 'Button Settings'.
5. Select first '+'.
6. Follow in-app prompts to set up the first scenario launcher.
7. Select the next '+' and repeat steps to set up the second Scenario launcher.

Troubleshooting tips when pairing Smart Shading equipment to a TaHoma switch

1. Bring the TaHoma switch and smartphone/device closer to the equipment you are trying to pair.
2. Equipment Intervention:
   • Motor/Actuator: Press and hold the motor until it jogs twice (placing the motor into pairing/discovery mode) and repeat configuration process.
   • Ysia Control: Factory reset the Ysia control and repeat configuration process.
3. Add the equipment using the alternative method (i.e. QR code or Zigbee mesh discovery).
4. Strengthen the mesh network by adding a trusted Somfy repeater (including Sonesse 40 Zigbee AC, Glydea Ultra AC with Zigbee Module, Izymo Motor or On/Off Receiver and or a Philips Hue Smart Plug.

Smart Shading Equipment

Steps to factory reset Smart Shading equipment