Large Full Motion Mount for 47" - 84" TVs

Important Safety Instructions

SAVE THESE INSTRUCTIONS

CAUTION: Do not use this product for any purpose not explicitly specified by BEST BUY ESSENTIALS. Improper installation may cause property damage or personal injury. If you do not understand these directions, or have doubts about the safety of the installation, contact Customer Service or call a qualified contractor. Best Buy Essentials is not responsible for damage or injury caused by incorrect installation or use.

The weight of your TV must not exceed 110 lbs. (50 kg). The wall must be capable of supporting five times the weight of your TV and wall mount combined.

This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children!

Features

• Supports TVs from 47-84" and up to 110 lbs. (50 kg)
• Mounts to VESA patterns from 200 x 200 to 600 x 400 (with all common sizes in between)
• Adjust the viewing angle by swiveling and tilting
• Years of dependable use with sturdy steel construction
• Built and backed by Best Buy

Specifications

VESA TV Screw Hole Patterns

Your wall mount works with the following VESA TV screw hole patterns:

• 200 x 200 mm (7.9 x 7.9")
• 400 x 200 mm (15.7 x 7.9")
• 500 x 400 mm (19.7 x 15.7")
• 300 x 200 mm (11.8 x 7.9")
• 400 x 300 mm (15.7 x 11.8")
• 600 x 400 mm (23.6 x 15.7")
• 300 x 300 mm (11.8 x 11.8")
• 400 x 400 mm (15.7 x 15.7")

Dimensions

Approximate dimensions of the mount:

• Width: 18.1 in. (46 cm)
• Height: 18 in. (45.7 cm)
• Depth (wall to mount): 16.9 in. (43 cm)
• Maximum Extension: 26.1 in. (66.4 cm)

Tools Needed

You need the following tools to assemble your new TV wall mount:

• Measuring tape
• Pencil
• Phillips screwdriver
• Drill
• Hammer
• Socket wrench
• 5 mm Allen wrench
• 3/16 in. (5 mm) wood drill bit (for wood stud walls)
• 3/8 in. (10 mm) masonry drill bit (for concrete walls)
• Tape
• Edge-to-edge stud finder

Package Contents

Parts

TV Hardware Bag

Installation Instructions

STEP 1 - Determine TV Back Type

Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and scratches. If your TV has a table-top stand attached, remove the stand. Lay the TV brackets, oriented vertically, on the back of your TV. Align the screw holes in the TV brackets with the mounting screw holes on your TV. Identify which type of back your TV has:

• Flat back: The brackets lay flush against the back of your TV and do not block any jacks. You do not need spacers when assembling the wall mount.
• Obstructed back: The brackets block one or more of the jacks on the back of your TV. You need spacers when assembling the wall mount.
• Irregularly-shaped back: There is a gap between a bracket and some part of the back of your TV. You need spacers when assembling the wall mount.

After identification, remove the TV brackets.

STEP 2 - Select Screws, Washers, and Spacers

Select the hardware for your TV (screws, washers, and spacers). Some TVs come with mounting hardware included, often found in the TV's back mounting holes. If you are unsure of the correct screw length, test-fit screws by hand. For a TV with a flat back, use shorter screws (A1, A3, A5, A8). For a TV with an irregular/obstructed back, use longer screws (A2, A4, A6, A7, A9, A10) and spacers (A11, D, or E). Use M4/M5 washers (A12) with M4/M5 screws, and M6/M8 washers (A13) with M6/M8 screws. Ensure adequate thread engagement to secure the brackets; do not over-tighten. Use the shortest screw and spacer combination that accommodates your TV securely. Using hardware that is too long may damage your TV, while hardware that is too short may cause the TV to fall.

STEP 3 - Attach Mounting Hardware to TV

Option 1: For a Flat Back TV

Align the left and right TV brackets with the screw holes on the back of your TV, ensuring they are level. Install washers (A12 or A13) and screws (A1, A3, A5, or A8) into the holes. Tighten the screws until they are snug against the TV brackets. Do not over-tighten.

Option 2: For an Irregular or Obstructed Back TV

Place spacers (A11, D, or E) over the screw holes on the back of your TV. Align the left and right TV brackets with the screw holes, ensuring they are level. Place washers (A12 or A13) over the bracket holes. Insert screws (A2, A4, A6, A7, A9, or A10) through the washers, TV brackets, and spacers, and into the TV screw holes. Tighten the screws until they are snug against the TV brackets. Do not over-tighten.

STEP 4 - Determine Wall-Mount Location

Measure the distance from the bottom of your TV to the center of its mounting holes (measurement 'a'). Measure from the floor to where you want the bottom of your TV to be placed on the wall (measurement 'b'), ensuring it clears any furniture. The total measurement for the center of the wall plate on the wall is 'a + b'. Mark this spot on the wall. An online height-finder tool is available at: http://mf1.bestbuy.selectionassistant.com/index.php/heightfinder

STEP 5 - Install Wall Plate

Option 1: Install on a Wood Stud Wall

Note: Any drywall covering the wall must not exceed 5/8 in. (16 mm).

Locate a wood stud using an edge-to-edge stud finder. Align the center of the wall mount template at the calculated height mark (a + b), ensuring it is level, and tape it to the wall. Drill four pilot holes through the template to a depth of 2.4 in. (60 mm) using a 3/16 in. (5 mm) diameter drill bit. Remove the template. Align the wall plate on the wall mount with the pilot holes. Insert lag bolts (A) through lag bolt washers (C), then through the holes in the wall plate. Ensure the wall plate is level. Tighten the lag bolts with a socket wrench until they are firm against the wall plate. DO NOT over-tighten the lag bolts.

Option 2: Install on a Solid Concrete or Concrete Block Wall

CAUTION: To prevent property damage or personal injury, never drill into the mortar between blocks. Mount the wall plate directly onto the concrete surface.

Align the center of the wall mount template at the calculated height mark (a + b), ensuring it is level, and tape it to the wall. Drill four pilot holes through the template to a depth of 2.4 in. (60 mm) using a 3/8 in. (10 mm) diameter masonry drill bit. Remove the template. Insert the concrete wall anchors (B) into the pilot holes and use a hammer to ensure the anchors are flush with the concrete surface. Align the wall plate on the wall mount with the anchors. Insert lag bolts (A) through lag bolt washers (C), then through the holes in the wall plate. Ensure the wall plate is level. Tighten the lag bolts with a socket wrench until they are firm against the wall plate. DO NOT over-tighten the lag bolts.

STEP 6 - Secure Your TV to the Wall Plate

HEAVY! You will need assistance with this step. Holding your TV with the top of the screen tilted toward the wall, slide the upper edges of the right and left TV brackets into the notches on the upper lip of your TV wall plate. Push the bottom of your TV toward the wall until the safety bolts click into place, then tighten the bolts with a Phillips screwdriver. CAUTION: Do not release your TV until the TV brackets are securely locked onto the wall plate.

STEP 7 - Manage Cables

Thread cables for attached devices along the mounting arm, then snap the cable holders (3 included) over the cables to hold them in place.

STEP 8 - Adjust Mount Arm and Tilt Angles

To adjust the arms' tension (to make the arm easier or harder to move), loosen or tighten the tension screws with an Allen wrench. To rotate your TV left or right, hold the sides of your TV, then push one side while pulling the other. To tilt your TV up or down, hold the top and bottom of your TV, then tilt your TV forward or backward. If the TV screen sags, tighten the two bolts on the TV plate with a socket wrench until they are snug.

One-Year Limited Warranty

This Best Buy Essentials product is warranted against defects in material and workmanship for one year from the date of purchase. This warranty covers repair or replacement of defective products or parts. It does not cover damage from misuse, accident, cosmetic damage, or unauthorized repairs. For service, contact Best Buy Essentials at 1-866-597-8427 or visit www.bestbuy.com/bestbuyessentials. This warranty is valid only in the United States and Canada.

Product Inquiries

For product inquiries, please contact Best Buy Essentials:

1-866-597-8427 | www.bestbuy.com/bestbuyessentials

BEST BUY ESSENTIALS is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC, 7601 Penn Ave South, Richfield, MN 55423 U.S.A. ©2023 Best Buy. All rights reserved.