SURGEX SX-DSP-129 Switched IP Controllable Surge Protected PDU User Guide

User Guide for SURGEX models including: SX-DSP-129, SX-DSP-169, SX-DSP-109i, SX-DSP-169i, SX-DSP-129 Switched IP Controllable Surge Protected PDU, SX-DSP-129, Switched IP Controllable Surge Protected PDU, Controllable Surge Protected PDU, Surge Protected PDU, Protected PDU

UM-Squid-Rev-A

SurgeX Squid User Manual

SurgeX

b01-00008 defender-series-quick-start-guide- 3403 7

SURGEX DEFENDER 9 SALIDAS 240V/16A IP CONTROL

Defender Series Quick Start Guide

Defender Series 120-208V Surge Suppression

Quick Start Guide

3.2 USB-OTG Port: i. Connect the Defender Series to your computer using a USB -A to Micro-USB cable. ii. Plug the device into an AC power source.

File Info : application/pdf, 7 Pages, 1.21MB

b0100008defender-series-quick-start-guide ?la=en&revision=fec66f07-d609-42e9-8339-748e48cdd3d7

Quick Start Guide
1. Installation and Components

SX-DSP-129

SX-DSP-169

SX-DSP-109i

SX-DSP-169i

Defender Series+ is designed to be installed on the back of an equipment rack. The supplied nuts, bolts, and washers must be used to mount the Defender Series+ to the rack through the mounting holes (A) following the appropriate local regulations and requirements.
1.1 AC Power: Output Plug the equipment cord (B) into the suitable outlet as needed. In Manual, review Introduction,
Physical Interfaces, and column Outputs for the suitable plugs for each model's outlets.
1.2 AC Power: Input Connect power to the Defender Series+ using an appropriately rated 3-wire grounding type
power cord provided with the equipment in inlet (V). Do not plug the unit into a relocatable power tap. Check the outlet for correct polarity and presence of a ground conductor before plugging the unit in.

1.3 Ethernet The RJ-45 connector for Ethernet (D) is situated on the front panel and is only to be used for
setup and debugging. The default IP Address is DHCP assigned. To find IP address of the device, please use the discovery tool at ametekesp.com. The mDNS protocol is supported for dynamic device discovery.

The default login credentials are:

Username: admin Password: Adm1nXXXXXX

Where XXXXXX are the last six characters of the MAC address.

1.4 USB-Micro AB The USB-Micro AB connector (E) is for diagnostics and troubleshooting IP connectivity issues.
To use, please use the discovery tool at ametekesp.com or manually enter the static IP address https://169.254.10.100 into a supported browser. The web server will always be accessible at https://169.254.10.100 through this USB port. The web server on this interface cannot be changed and will always be unsecured HTTP at port 80.

Quick Start Guide
1.5 LED Indicators: The outlets have individual power indicator LEDs (F). These are paralleled in the control
interface. In addition, the unit has an LED indicating power (G). Self -Test is indicated by (C).
1.6 Buttons
1.6.1 Resettable fuse The resettable fuse (H) is used to reset the Defender Series+ in case the fuse trips. This is a single push button located at the bottom left of the Ethernet RJ-45 jack. Also, there is a reset switch for hardware and another for software.
1.6.2 Hardware Reset Hardware Reset (I): The Hardware Reset button performs a hard reboot of the processor. This hard reboot will immediately switch controlled outlets off, removing power to connected equipment on all outputs.
1.6.3 Software Reset Software Reset (J): The Software Reset button is a multi-functional control depending on length of press. If the button is held for longer than 10 seconds, the unit resets itself to factory defaults, and all custom configurations are erased. If the button is held for less than 10 seconds, the unit will perform a software reset that will not reset any data, or power cycle the connected equipment.

Quick Start Guide
2. Rack Installation
Defender Series+ is designed to be installed in the equipment rack. The supplied nuts, bolts, and washers must be used to mount the Defender Series+ to the rack through the mounting holes (A), (B), (C), or (D) following the appropriate local regulations and requirements.

Quick Start Guide

3. Access to the Graphic User Interface via Computer
There are two ways to gain access to the internal Web Server where further setup and configuration is available.
3.1 RJ-45 Ethernet Port: i. Connect the Defender Series+ to a standard Ethernet network. ii. Plug the device into an AC power source. By default, the device is set to DHCP and will pull an IP address once it is connected to an AC power source, assuming that your network is set to DHCP. If your network is set for Static IP addresses, you may want to initially access the unit via the USB-OTG Port, then go into the Network setting to change over to Static IP addressing. iii. To find the IP address of the device, you can download the free SurgeX IP address discovery tool at www.surgex.com. Alternatively, you can use a third-party IP address discovery tool, or look at the IP table built into the network's router. iv. Using any web browser, type in the unit's IP address to access the login page. The default login credentials are:
Username: admin Password: Adm1nXXXXXX
Where XXXXXX are the last 6 characters of the unit's MAC address. Change your password after logging in for the first time to minimize security issues.

Quick Start Guide
3.2 USB-OTG Port: i. Connect the Defender Series+ to your computer using a USB-A to Micro-USB cable. ii. Plug the device into an AC power source. iii. Using any web browser, type in the default IP address https://169.254.10.100 to access the login page. The default login credentials are: Username: admin Password: Adm1nXXXXXX Where XXXXXX are the last 6 characters of the unit's MAC address. Change your password after logging in for the first time to minimize security issues.

References

Adobe PDF Library 24.2