Manuals+

HOMODEN

Installation Instruction

Scan the QR code to download the companion APP for operating the lights.

Note: APP connection method is Bluetooth.

SPECIFICATIONS

  • Input Voltage: 120V
  • Frequency: 60Hz
  • Product Dimensions: 30 inches x 30 inches x 10 inches
  • LED Light Power: 24 watts
  • Color Temperature: 3000/3500/4000/5000/5500/6000K
  • Ingress Protection rating: IP20 (Indoor Use Only)

WARNING

⚠️ To prevent the risk of fire, electric shock, and serious personal injury, please follow these instructions:

  1. Review the User Manual: Before installing your new fan, thoroughly read the user manual and safety information. Please review the assembly drawings carefully to check if any components are missing.
  2. Turn Off Power: Please ensure to disconnect the power supply when installing, servicing, or cleaning the light fixture. To ensure safety and prevent potential electrical shock, it is not sufficient to simply turn off the wall switch. Prior to wiring, make sure to turn off the electricity at the main fuse box. All wiring should be done in accordance with national and local electrical codes. Additionally, it is important to properly ground the ceiling fan as a precautionary measure against possible electrical shock.
  3. Electrical and Structural Requirements: Your new ceiling fan will require a grounded electrical supply line of AC110-130V/60Hz and a 15 Amp circuit. According to electrical codes, it is necessary to use a fan-rated outlet box to support the additional weight and motion associated with a ceiling fan. A fan-rated box will be clearly labeled as such and is typically designed to support ceiling fans weighing up to 70 pounds. Fan-rated outlet boxes are available in various ratings and designs. It is essential to ensure that the rating of your ceiling fan outlet box meets the requirements for the specific ceiling fan you are installing.
  4. No Objects in Blades: Do not insert any objects into the fan blades while the fan is in operation.
  5. Supervise Children: This appliance is not intended for use by young children or individuals with disabilities without supervision. Ensure that young children are closely supervised to prevent them from playing with the appliance.
  6. Consult a Licensed Electrician: Before installing your ceiling fan, consult the section on the proper wiring method for your fan. If you feel that you lack sufficient knowledge or experience in wiring, it is highly recommended to have a licensed electrician install your fan.
  7. Choosing the Appropriate Mounting Location: Ceiling fans should be installed or mounted in the middle of the room and positioned at least 7 feet above the floor and 18 inches away from the walls. If the ceiling height allows, it is recommended to install the fan 7~9 feet above the floor to achieve optimal airflow.
  8. Do not use a full range dimmer switch to control the fan: Using a full range dimmer switch to control fan speed will damage the fan. To reduce the risk of fire or electrical shock, do not use a full range dimmer switch to control the fan speed. Only control light on/off via wall fan switch and the provided remote control.

Tool Preparation Prior to Installation

  • ? Ladder
  • ? Screwdriver
  • ✂️ Wire Strippers
  • ? Goggles

ASSEMBLY DRAWING & PARTS LIST

ATTENTION

Transfer the loose parts from their bags into a small container to prevent them from getting lost. If any parts are missing, please get in touch with us.

Assembly Drawing

The assembly drawing illustrates the main components of the ceiling fan and how they connect. Key parts include the mounting plate, receiver, decorative cover, fan motor assembly, blades, lamp plate, lamp cover, and remote control.

Parts Inventory

Ref.# Description QTY
1Mounting Plate1
2Receiver1
3Decorative cover1
4Fan Motor Assembly1
5Blade3
6Lamp plate1
7Lamp cover1
8Remote Control1
9Accessory bag for Mounting Plate1
10Accessory bag for blade1
11Remote Control Accessory bag1
12Bracket screw (4pcs pre-installed)1
13Canopy screw (6pcs pre-installed)1

Note: For part 8 (Remote Control), please consult the remote control manual for instructions on its use.

I. Mount the mounting bracket to the ceiling

  1. Step 1-1: Remove the Mounting bracket and Decorative Cover.
  2. Step 1-2: Loosen the two screws in the 'L' slot, then remove the other two screws and rotate to remove the bracket.
  3. Step 2-1: Ensure that the main power supply to the ceiling is reserved and turned off. The diagram shows a switch indicator in the 'OFF' position.
  4. Step 2-2: Connect the live wire (black), neutral wire (white), and ground wire (green) to the cord.

⚠️ WARNING: Please turn off the main power supply before beginning any installation.

Ceiling Mounting Options

  1. Step 3-1 (Wooden ceiling): Use self-tapping screws to drive into the wooden ceiling. (Use Accessory Bag Reference #9 for the mounting bracket.)
  2. Step 3-2 (Cement ceiling): Drill holes on the cement ceiling, then use expansion tubes and self-tapping screws for fixing. (Use Accessory Bag Reference #9 for the mounting bracket.)
  3. Step 3-3 (Junction box): Use j-box screws and washer to fix the bracket to the ceiling.

II. Installation of the fan

  1. Step 4: Remove the Fan Motor Assembly and inspect the blade mounting holes (Blade Hole #1, Blade Hole #2, Blade Hole #3).
  2. Step 5: Fasten the upper section of the fan blade using two screws, and secure the lower section with a single screw. Refer to Accessory Bag Reference #10 for the blade components. For convenience, align the notch position with each blade screw hole before inserting the screws during installation.

Fan Blade Installation

  1. Step 6: Finish the installation of all three fan blades.
  2. Step 7: Use a screwdriver to unscrew the six screws from the fan motor.

Decorative Cover Installation

  1. Step 8: Thread the power cord of the motor through the central hole of the decorative cover and then secure the decorative cover onto the motor using the six screws that were previously removed from the motor.
  2. Step 9: Remove three screws from the triangular piece.

LED Wire and Lamp Plate Installation

  1. Step 10: Carefully extend the LED wire about 2 inches away from the triangular plate.
  2. Step 11: Remove the lamp plate and pass the wire terminals of the LED through the hole at the center of the lamp plate.

LED Connection

  1. Step 12: Connect the LED terminal; a [click] sound indicates a proper connection.
  2. Step 13: Push the LED wire back into the hole to prevent any light shadows when the light is turned on.

Lamp Panel and Receiver Connection

  1. Step 14: Use the three screws removed in step 9 to secure the lamp panel onto the triangular piece.
  2. Step 15: Connect the motor power wire (3 lines) and LED power wire (3 lines) to the receiver socket. Ensure successful connection when you hear a [click] sound.

Model Details:

  • Model: DC10508
  • Voltage: 24V
  • Size: 30"
  • Input Voltage: 120V
  • Power: 30W

III. Wiring

  1. Step 16: Suspend the hole in the decorative cover on the hook of the mounting bracket to make wire connection easier.
  2. Step 17: Connect the main power to the receiver.

IV. Mounting the fan on the ceiling

  1. Step 18: After connecting the wires, place the receiver into the mounting plate, and then detach the fan body from the hook.
  2. Step 19: Hang the two slots on the decorative cover onto the two screws of the mounting bracket, and then rotate the fan anticlockwise by 2-3 centimeters.

Securing the Fan and Lamp Cover

  1. Step 20: Use the two screws that were removed in step 1-2 and tighten them both. Secure the two screws on the two slots of the decorative cover. (Diagram shows screw positions: Screw-1, Screw-2, Screw-3, Screw-4).
  2. Step 21: Gently install the lamp cover onto the lamp body and secure it by rotating.

Installation Complete & Base Installation

  1. Step 22: The installation is finished.

Method for Installing the Base:

  • Method 1: Secure using the 3M tape.
  • Method 2: Fasten with screws.

(Use the Accessory bag Ref.#11 for remote control)

DCL Remote Control Manual

  1. To operate the fan, please install 2 AAA batteries (not included) in the handheld remote transmitter.
  2. If not used for extended periods of time, remove the batteries to prevent damage to the transmitter.
  3. Store the remote away from excessive temperatures and humidity.
  4. Ensure correct battery polarities are in place when using the remote control. LED indicator flashes each time a button is pressed.
  5. Maintains the specific status of lights and fans for 15 seconds to activate memory function, ensuring your preferences are saved.

Remote Control Layout:

  • Gear indicator (gear 1-6)
  • Code matching
  • Main off (code key)
  • Timing key (reduce)
  • Fan gear key (reduce)
  • Switch color temperature
  • Brightness (reduce)
  • Forward/reverse key
  • Natural wind (code key)
  • Timing off key
  • Timing key (increase)
  • Fan gear off key
  • Fan gear key (increase)
  • Night mode
  • Sound on/off key
  • Brightness (increase)
  • Light on/off key

How to pair a code?

Within 5 seconds after putting the battery in, keep pressing the "Main Off" + "Natural Wind" two buttons at the same time until you hear a "[di-sound]" sound, then the code matching is successful.

Note: If the remote control is lost, please use a new remote control to do new code matching; then the old remote control is disabled.

Troubleshooting

PROBLEM SUGGESTED REMEDY
If Fan Does Not Start
  1. Check the main and branch circuit fuses or circuit breakers.
  2. Ensure that the wall control is turned "ON"; do not use a dimmer switch.
  3. Check the line wire connections to the fan and switch wire connections in the switch housing.

⚠️ CAUTION: Make sure to turn off the main power before making any electrical connections.
If The Fan Sounds Noisy
  1. Make sure all screws in the motor housing are snug (not over tightened).
  2. Check that wire connectors in the switch housing are not rattling against each other or the interior wall of the switch housing.
  3. Ensure that the screws securing are tight. Make sure the light bulb is tight in the socket and not touching the lamp frame or blades.
  4. Note that some fan motors are sensitive to signals from Solid State variable speed controls; DO NOT USE a Solid State variable speed control.
  5. Allow a "break-in" period of 24 hours. Most noises associated with a new fan will disappear after this period.

⚠️ CAUTION: Turn off the main power before entering the switch housing.
If Fan Wobbles
  1. Check that all blades are screwed firmly into blade holders.
  2. Make sure that the canopy and mounting bracket are tightened securely to the ceiling junction box, and the junction box is mounted firmly to the ceiling joist.
  3. Ensure the concave groove of the hanger ball is positioned on the hanger lug of the mounting bracket.
If Light Does Not Work Check the wire terminal connection, make sure it is tightened.

⚠️ CAUTION: Make sure the main circuit is turned off before entering the switch housing.
Remote Does Not Work
  1. Battery out of power or not installed correctly: change new AAA battery and ensure it is well installed.
  2. Remote controller not paired: make new pairing with light (Refer to Page 15).
Models: FS20023X Wood Blade Low Profile Ceiling Fan Lamp, FS20023X, Wood Blade Low Profile Ceiling Fan Lamp, Low Profile Ceiling Fan Lamp, Ceiling Fan Lamp, Fan Lamp

File Info : application/pdf, 18 Pages, 8.82MB

D1EM9JAdtnL Adobe PDF library 15.00