Instruction Manual for TOA models including: F-03BT, F-03WT, F-05BT, F-05WT, F-08BT, F-08WT, F-08WT Speaker System, Speaker System, Speaker
Loa subwoofer TOA FB-08BT / FB-08WT
3 set 2024 — Thank you for purchasing TOA's Speaker System. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment. Page ...
File Info : application/pdf, 24 Pages, 1,008.05KB
DocumentDocumentSPEAKER SYSTEM INSTRUCTION MANUAL F-03BT, F-03WT F-05BT, F-05WT F-08BT, F-08WT F-03BT, F-03WT F-05BT, F-05WT F-08BT, F-08WT Thank you for purchasing TOA's Speaker System. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment. TABLE OF CONTENTS 1. SAFETY PRECAUTIONS ............................................................................. 3 2. GENERAL DESCRIPTION AND FEATURES .................................. 4 3. HANDLING PRECAUTIONS ...................................................................... 4 4. IMPEDANCE CHANGE ................................................................................. 5 5. DIMENSIONAL DIAGRAM .......................................................................... 6 5.1. F-03BT, F-03WT ................................................................................................... 6 5.2. F-05BT, F-05WT ................................................................................................... 6 5.3. F-08BT, F-08WT ................................................................................................... 7 6. SPEAKER CABLE CONNECTIONS ..................................................... 7 7. INSTALLATION .................................................................................................. 8 7.1. Using the Supplied Brackets ................................................................................ 8 7.2. Range of Speaker Installation Angle .................................................................. 10 7.3. Wall Mounting ..................................................................................................... 13 7.4. Ceiling Mounting ................................................................................................ 16 8. INSTALLATION EXAMPLES USING THE OPTIONAL ADAPTER PLATES ............................... 19 9. SPECIFICATIONS ........................................................................................... 20 9.1. F-03BT, F-03WT ................................................................................................. 20 9.2. F-05BT, F-05WT ................................................................................................. 21 9.3. F-08BT, F-08WT ................................................................................................. 22 2 1. SAFETY PRECAUTIONS · Before installation or use, be sure to carefully read all the instructions in this section for correct and safe operation. · Be sure to follow all the precautionary instructions in this section, which contain important warnings and/or cautions regarding safety. · After reading, keep this manual handy for future reference. Safety Symbol and Message Conventions Safety symbols and messages described below are used in this manual to prevent bodily injury and property damage which could result from mishandling. Before operating your product, read this manual first and understand the safety symbols and messages so you are thoroughly aware of the potential safety hazards. WARNING Indicates a potentially hazardous situation which, if mishandled, could result in death or serious personal injury. · Install the speaker only in a location that can structurally support the weight of the speaker and the mounting bracket. Doing otherwise may result in the speaker falling down and causing personal injury and/or property damage. · Since the speaker is designed for indoor use, do not install it outdoors. If installed outdoors, the aging of parts causes the speaker to fall off, resulting in personal injury. Also, when it gets wet with rain, there is a danger of electric shock. · (F-08BT and F-08WT only) Owing to the speaker's size and weight, be sure that at least two persons are available to install the speaker. Failure to do so could result in personal injury. · Do not use anti-rust lubricant. If it contacts resin or rubber parts, they could deteriorate and cause the speaker to fall, possibly resulting in personal injury. · Do not install the speaker near the seashore or in locations where corrosive gas is generated, such as swimming pool facilities. If installed in such environments, its mounting bracket may rust or corrode. This could cause the speaker to fall, potentially resulting in personal injury. CAUTION Indicates a potentially hazardous situation which, if mishandled, could result in moderate or minor personal injury, and/or property damage. · Avoid touching the speaker's sharp metal edge to prevent injury. · To avoid electric shocks, be sure to switch off the amplifier's power when connecting speakers. · Do not use other methods than specified to mount the bracket. Extreme force is applied to the speaker and the speaker could fall off, possibly resulting in personal injuries. · Attach the safety wire to the speaker. If not attached, the speaker could fall off, resulting in personal injury. · Use nuts and bolts that are appropriate for the ceiling's or wall's structure and composition. Failure to do so may cause the speaker to fall, resulting in material damage and possible personal injury. · Tighten each nut and bolt securely. Ensure that the bracket has no loose joints after installation to prevent accidents that could result in personal injury. · Use the specified mounting bracket in combination. Doing otherwise may cause the speaker or component to fall off, resulting in personal injury. · Do not place heavy objects on the speaker as this may cause it to fall or break which may result in personal injury and/or property damage. In addition, the object itself may fall off and cause injury and/or damage. · Do not operate the speaker for an extended period of time with the sound distorting. Doing so may cause the connected speakers to heat, resulting in a fire. · Do not stand or sit on, nor hang down from the speaker as this may cause it to fall down or drop, resulting in personal injury and/or property damage. · Have the speaker checked periodically by the shop from where it was purchased. Failure to do so may result in corrosion or damage to the speaker or its mounting bracket that could cause the speaker to fall, possibly causing personal injury. · Do not mount the speaker in locations exposed to constant vibration. The mounting bracket can be damaged by excessive vibration, potentially causing the speaker to fall, which could result in personal injury. 3 2. GENERAL DESCRIPTION AND FEATURES · Compact speakers with high quality sound that can suit a wide range of scenes such as background music and announcement use. · The table below shows the differences among models of the F-03BT/03WT, the F-05BT/05WT, and the F-08BT/08WT. Model F-03BT (Black), F-03WT (White) F-05BT (Black), F-05WT (White) F-08BT (Black), F-08WT (White) Speaker unit Full range (9 cm or 3.5" speaker) 2-way (13 cm or 5" woofer and 25 mm or 1" dome tweeter) 2-way (20 cm or 8" woofer and 25 mm or 1" dome tweeter) · Excellent design of speakers that can blend with a wide variety of architectural styles, making the speakers ideal for installation in various scenes. · Supplied mounting brackets and optional adapter brackets allow the speakers to fit the installation location and the application. ·The supplied mounting bracket can be installed to a wall or ceiling, enabling the adjustment of the speaker's orientation vertically and horizontally. · The optional adapter plate allows the speaker to be installed on a speaker stand. · Additionally, ease of installation as the speaker's position can easily be set or reset, allowing both hands to be free for adjustments or wiring. 3. HANDLING PRECAUTIONS · Only install the speaker in locations with an ambient operating temperature range of -10 to +50 °C (14 to 122 °F). Failure to follow this instruction could result in speaker malfunction or failure. · The range of the speaker installation angles varies depending on the installation location and the orientation of the mounting bracket. For the speaker installation angle, see "Range of Speaker Installation Angle" on p. 10. 4 4. IMPEDANCE CHANGE To change the impedance, use a standard screwdriver to rotate the rotary switch on the speaker's rear to select the desired input power. [F-03BT or F-03WT] [F-05BT or F-05WT] Factory-preset : 670 [F-08BT or F-08WT] Factory-preset : 330 Note Never set the switch to " " position for 100 V line operation, as doing so may result in damage to the speaker. Factory-preset : 170 5 5. DIMENSIONAL DIAGRAM 5.1. F-03BT, F-03WT [Front] 130 (5.12") [Side] 132 (5.2") [Rear] 40 (1.57") Unit: mm 221 (8.7") 40 (1.57") [Side (with bracket)*] 203 (7.99") 5.2. F-05BT, F-05WT [Front] 162 (6.38") * The installation position of the bracket is for vertical installation. [Side] 164 (6.46") [Rear] 45 (1.77") Unit: mm 274 (10.79") 45 (1.77") [Side (with bracket)*] 246 (9.69") * The installation position of the bracket is for vertical installation. 6 5.3. F-08BT, F-08WT [Front] 251 (9.88") [Side] 216 (8.5") [Rear] 60 (2.36") Unit: mm 392 (15.43") 60 (2.36") [Side (with bracket*)] 301 (11.85") * The installation position of the bracket is for vertical installation. 6. SPEAKER CABLE CONNECTIONS [Input terminal polarity] [Stripped conductor of cable] Input terminal 10 mm (0.39") (-) (+) BLACK RED Rear The figure represents the F-05BT or F-05WT. 7 7. INSTALLATION 7.1. Using the Supplied Brackets The speaker system is supplied with the following brackets. · Base bracket: Used when installing the speaker to a wall or ceiling F-03BT F-03WT F-05BT F-05WT F-08BT F-08WT · Speaker brackets: To be attached to the speaker's rear surface F-03BT F-03WT F-05BT F-05WT F-08BT F-08WT 7.1.1. Installation Location of the Base Bracket When installing the base bracket to a wall or ceiling, refer to the installation location diagrams and position dimensions table shown below. Shown below are the minimum distances from the wall or ceiling to the base bracket, taking into consideration the speaker installation angle. For the speaker installation angle, see "Range of Speaker Installation Angle" on p. 10. [When installing to a wall] · The figures are front views. · The base bracket in the diagrams is that of the F-05BT or F-05WT. (Vertical installation) Ceiling Speaker (Horizontal installation) Ceiling Speaker D B Wall Wall A Base bracket C Base bracket Unit: mm A B C D F-03BT 170 250 220 250 F-03WT (6.69") (9.84") (8.66") (9.84") F-05BT 200 300 250 200 F-05WT (7.87") (11.81") (9.84") (7.87") F-08BT 300 450 350 300 F-08WT (11.81") (17.72") (13.78") (11.81") [When installing to a ceiling] · The figures are bottom view. · The base bracket in the diagram is that of the F-05BT or F-05WT. (Vertical installation) Wall Speaker Wall B (Horizontal installation) Wall Speaker Wall D A Base bracket C Base bracket Unit: mm A B C F-03BT 150 250 150 F-03WT (5.91") (9.84") (5.91") F-05BT 150 250 200 F-05WT (5.91") (9.84") (7.87") F-08BT 200 300 250 F-08WT (7.87") (11.81") (9.84") D 250 (9.84") 250 (9.84") 250 (9.84") 8 7.1.2. Base bracket installation dimensions The number of the mounting holes in the base bracket varies depending on the model and the mounting location, which is a wall (3-point installation) or a ceiling (2- or 4-point installation). Use M6 bolts and nuts for installation. Unit: mm Model When installing to a wall When installing to a ceiling F-03BT F-03WT [3-point installation] 12.3 (0.48") Mounting hole ø6.5 (0.26") ø32 (1.26") [2-point installation] 26.3 (1.04") F-05BT F-05WT M6 bolt 24.6 (0.97") Mounting hole [3-point installation] 18.6 (0.73") Mounting hole ø6.5 (0.26") ø42 (1.65") M6 bolt 32 (1.26") Mounting hole [4-point installation] 29.7 (1.17") 29.7 (1.17") 30.7 (1.21") F-08BT F-08WT M6 bolt 37.2 (1.46") Mounting hole M6 bolt Mounting hole [3-point installation] 23.5 (0.93") Mounting hole ø6.5 (0.26") ø52 (2.05") [4-point installation] 36.8 (1.45") 36.8 (1.45") 37 (1.46") M6 bolt 47 (1.85") Mounting hole M6 bolt Mounting hole 9 7.2. Range of Speaker Installation Angle Install the speakers within the shaded range shown in the table below. 7.2.1. F-03BT, F-03WT [When installing to a wall] Installation examples Horizontal angle adjustment range 78° left and right from the center of the speaker (Top view) Vertical angle adjustment range 0º horizontal to 45º downward (Side view) Vertical installation 0° Horizontal 78° 78° 45° 0° 45° left and right from the center of the speaker (Top view) The angle can be adjusted in 15° steps. 0º horizontal to 75º downward (Side view) 0° Horizontal Horizontal installation 75° 45° 45° 0° The angle can be adjusted in 15° steps. [When installing to a ceiling] Installation examples Horizontal angle adjustment range 40° left and right from the reference point mentioned below* Base bracket Ceiling mounting surface Vertical angle adjustment range 45º downward to 90º downward (Side view) Ceiling 0° Horizontal 40° Vertical installation 45° 40° Ceiling Speaker cable exit hole Reference point 40° left and right from the reference point mentioned below* Base bracket Ceiling mounting surface (90°) (45°) The angle can be adjusted in 15° steps. 15º downward to 90º downward (Side view) 0° Horizontal 40° Horizontal installation 15° 40° (90°) (75°) Speaker cable exit hole Reference point The angle can be adjusted in 15° steps. * In the case of the ceiling installation, adjust the horizontal angle by positioning the base bracket. 10 7.2.2. F-05BT, F-05WT [When installing to a wall] Installation examples Wall Horizontal angle adjustment range 70° left and right from the center of the speaker (Top view) Vertical angle adjustment range 0º horizontal to 60º downward (Side view) Vertical installation 0° Horizontal 70° 70° 60° 0° The angle can be adjusted in 10° steps. 40° left and right from the center of the speaker 0º horizontal to 70º downward (Top view) (Side view) Wall 0° Horizontal Horizontal installation 70° 40° 40° 0° The angle can be adjusted in 10° steps. [When installing to a ceiling] Installation examples Ceiling Horizontal angle adjustment range 17.5° left and right from the reference point mentioned below* Base bracket 17.5° Ceiling mounting surface Vertical angle adjustment range 30º downward to 90º downward (Side view) 0° Horizontal 17.5° Vertical installation 30° (90°) Reference point (60°) Speaker cable exit hole The angle can be adjusted in 10° steps. Ceiling 17.5° left and right from the reference point mentioned below* Base bracket 17.5° Ceiling mounting surface 20º downward to 90º downward (Side view) 0° Horizontal 17.5° Horizontal installation 20° (90°) Reference point (70°) Speaker cable exit hole The angle can be adjusted in 10° steps. * In the case of the ceiling installation, adjust the horizontal angle by positioning the base bracket. 11 7.2.3. F-08BT, F-08WT [When installing to a wall] Installation examples Wall Horizontal angle adjustment range 60° left and right from the center of the speaker (Top view) Vertical angle adjustment range 0º horizontal to 60º downward (Side view) Vertical installation 60° 60° 0° 0° Horizontal 60° The angle can be adjusted in 10° steps. 30° left and right from the center of the speaker (Top view) 0º horizontal to 70º downward (Side view) Wall 0° Horizontal Horizontal installation 70° 30° 30° [When installing to a ceiling] Installation examples Ceiling Horizontal angle adjustment range 20° left and right from the reference point mentioned below* The angle can be adjusted in 10° steps. Vertical angle adjustment range 30º downward to 90º downward (Side view) Base bracket 20° Ceiling mounting surface 0° Horizontal 20° Vertical installation 30° Reference point (90°) (60°) Speaker cable exit hole The angle can be adjusted in 10° steps. 20° left and right from the reference point mentioned below* Base bracket 20° Ceiling mounting surface 20º downward to 90º downward (Side view) 0° Horizontal 20° Horizontal installation 20° Reference point (90°) (70°) Speaker cable exit hole The angle can be adjusted in 10° steps. * In the case of the ceiling installation, adjust the horizontal angle by positioning the base bracket. 12 7.3. Wall Mounting Note The figures are examples of the F-05BT or F-05WT. Step 1. Mount the supplied base bracket on the wall. Notes · Bolts and nuts used for mounting the base bracket to the wall are not supplied. Use M6 bolts and nuts. · For the installation location and dimension of the base bracket, see "Using the Supplied Brackets" on p. 8. · Be sure to mount the base bracket to the wall using 3 or more bolts as shown in the figure at right. Base bracket Wall Nut (3 spaces) Step 2. Attach a safety wire to the rear surface of the speaker. WARNING · Install the safety wire on the wall side to a location that is strong enough to withstand the entire weight of the speaker including the mounting brackets. · Use a safety wire that is strong enough to withstand the entire weight of the speaker including the mounting brackets. · Keep the safety wire at the minimum length without slack. Note The safety wire is not supplied. Prepare it separately. [Vertical installation] [Horizontal installation] Install the safety wire to either of the holes. Install the safety wire to either of the holes. Step 3. Secure the speaker bracket to the rear surface of the speaker using the supplied screws. Recommended tightening torque: 2 N·m Note The speaker bracket can also be mounted upside down. As the angle adjustment bolt is only provided on one side of the speaker bracket, install the bracket in the direction so that you can easily access the bolt for adjusting the speaker angle in Steps 5 and 6 after installing the speaker bracket to the base bracket in Step 4. [Vertical installation] [Horizontal installation] Speaker bracket Machine screw M5 x 20* Speaker bracket Machine screw M5 x 20* Angle adjustment bolt Angle adjustment bolt * with plain washer and spring washer, accessory 13 Step 4. Install the speaker bracket to the base bracket. 4-1. Insert the mounting hole in the speaker bracket onto the shaft of the base bracket fixed in Step 1. 4-2. To prevent the speaker from falling, temporarily fasten the speaker bracket and the base bracket with the supplied flange nut. Note Be sure to use the supplied flange nut. [Vertical installation] 4-2 Flange nut* (accessory) 4-1 Speaker bracket mounting hole [Horizontal installation] 4-2 Flange nut* (accessory) 4-1 Speaker bracket mounting hole Wall Wall Shaft Shaft Base bracket Base bracket * F-03BT, F-03WT, F-05BT, F-05WT: For M8 F-08BT, F-08WT: For M10 Step 5. Adjust the vertical angle by gradually loosening the angle adjustment bolt of the speaker bracket. · The speaker bracket is divided into part A and part B, which are secured with the angle adjustment bolt. The vertical angle is adjusted in the interlocking section of the parts A and B. Note Never remove the angle adjustment bolt or loosen it too much so that the parts A and B come off. · For the angle adjustment range, see "Range of Speaker Installation Angle" on p. 10. · Be sure to perform installation work while supporting the speaker with one hand. Speaker bracket (Side view) Part B Part A Wall Angle adjustment 5, 6 bolt The figure represents the vertical installation. Step 6. Tighten the angle adjustment bolt. Recommended tightening torque: 2 N·m Note Check that the parts A and B of the speaker bracket are firmly engaged. Step 7. Connect the speaker cable to the input terminal. (See p. 7.) Step 8. Adjust the horizontal angle of the speaker around the shaft of the base bracket as the axis, then firmly tighten the flange nut temporarily tightened in Step 4-2. [Recommended tightening torque] F-03BT, F-03WT, F-05BT, F-05WT: 10 N·m F-08BT, F-08WT: 20 N·m 14 Step 9. Attach the supplied base bracket cover to the base bracket using the supplied screw. Recommended tightening torque: 1 N·m Put the wiring cable into the base bracket cover taking care not to apply excessive force. [Vertical installation] Machine screw M4 x 8* [Horizontal installation] Machine screw M4 x 8* Base bracket cover Wall Base bracket cover Wall Base bracket Base bracket Brand mark Brand mark * with plain washer and spring washer, accessory Tip The brand mark is attached to the speaker's front grille with the double-sided adhesive tape. You can change the orientation of the brand mark, if needed. In this case, peel off the brand mark slowly and carefully, then you can reattach it after changing its orientation. 15 7.4. Ceiling Mounting Note The figures from Step 2 onward are examples of the F-05BT or F-05WT. Step 1. Temporarily secure the supplied base bracket to the ceiling. Notes · Bolts and nuts used for mounting the base bracket to the ceiling are not supplied. Use M6 bolts and nuts. · For the installation location and dimension of the base bracket, see "Using the Supplied Brackets" on p. 8. · Be sure to mount the base bracket to the ceiling using 2 or 4 bolts as shown in the figures below. [F-03BT or F-03WT] Ceiling [F-05BT, F-05WT, F-08BT, or F-08WT] Ceiling Base bracket Nut (2 spaces) Base bracket Nut (4 spaces) The figure represents the base bracket of F-05BT or F-05WT. Step 2. Attach a safety wire to the rear surface of the speaker. WARNING · Install the safety wire on the ceiling side to a location that is strong enough to withstand the entire weight of the speaker including the mounting brackets. · Use a safety wire that is strong enough to withstand the entire weight of the speaker including the mounting brackets. · Keep the safety wire at the minimum length without slack. Note The safety wire is not supplied. Prepare it separately. [Vertical installation] [Horizontal installation] Install the safety wire to either of the holes. Install the safety wire to either of the holes. 16 Step 3. Secure the speaker bracket to the rear surface of the speaker using the supplied screws. Recommended tightening torque: 2 N·m Note The speaker bracket can also be mounted upside down. As the angle adjustment bolt is only provided on one side of the speaker bracket, install the bracket in the direction so that you can easily access the bolt for adjusting the speaker angle in Steps 5 and 6 after installing the speaker bracket to the base bracket in Step 4. [Vertical installation] [Horizontal installation] Speaker bracket Machine screw M5 x 20* Speaker bracket Machine screw M5 x 20* Angle adjustment bolt Angle adjustment bolt * with plain washer and spring washer, accessory Step 4. Temporarily fix the speaker bracket to the base bracket. 4-1. Insert the mounting hole in the speaker bracket onto the shaft of the base bracket fixed in Step 1. 4-2. Temporarily fasten the speaker bracket and the base bracket with the supplied flange nut. Note Be sure to use the supplied flange nut. [Vertical installation] 4-1 Speaker bracket mounting hole Ceiling 4-2 Flange nut* Base bracket Shaft (accessory) [Horizontal installation] 4-1 Speaker bracket mounting hole 4-2 Flange nut* (accessory) Ceiling Base bracket Shaft * F-03BT, F-03WT, F-05BT, F-05WT: For M8 F-08BT, F-08WT: For M10 17 Step 5. Adjust the vertical angle by gradually loosening the angle adjustment bolt of the speaker bracket. · The speaker bracket is divided into part A and part B, which are secured with the angle adjustment bolt. The vertical angle is adjusted in the interlocking section of the parts A and B. Note Never remove the angle adjustment bolt or loosen it too much so that the parts A and B come off. · For the angle adjustment range, see "Range of Speaker Installation Angle" on p. 10. · Be sure to perform installation work while supporting the speaker with one hand. Ceiling Speaker bracket (Side view) Part B Part A Angle adjustment 5 6 , bolt The figure represents the horizontal installation. Step 6. Tighten the angle adjustment bolt. Recommended tightening torque: 2 N·m Note Check that the parts A and B of the speaker bracket are firmly engaged. Step 7. Connect the speaker cable to the input terminal. (See p. 7.) Step 8. Secure the speaker bracket to the base bracket by firmly tightening the flange nut temporarily tightened in Step 4-2. [Recommended tightening torque] F-03BT, F-03WT, F-05BT, F-05WT: 10 N·m F-08BT, F-08WT: 20 N·m Step 9. Adjust the horizontal angle by moving the base bracket as shown in the figure at right. For the angle adjustment range, see "Range of Speaker Installation Angle" on p. 10. Step 10. Firmly tighten the nuts temporarily tightened in Step 1 to secure the base bracket to the ceiling. Recommended tightening torque: 10 N·m Ceiling 9 Base bracket Step 11. Attach the supplied base bracket cover to the base bracket using the supplied screw. Recommended tightening torque: 1 N·m Put the wiring cable into the base bracket cover taking care not to apply excessive force. [Vertical installation] Ceiling [Horizontal installation] Machine screw M4 x 8* Ceiling Machine screw M4 x 8* 18 Base bracket cover Base bracket cover Brand mark Brand mark * with plain washer and spring washer, accessory Tip The brand mark is attached to the speaker's front grille with the double-sided adhesive tape. You can change the orientation of the brand mark, if needed. In this case, peel off the brand mark slowly and carefully, then you can reattach it after changing its orientation. 8. INSTALLATION EXAMPLES USING THE OPTIONAL ADAPTER PLATES You can install the speaker as shown in the examples below using the optional adapter plate*. For the installation method, refer to the installation manual supplied with the adapter plate. * The applicable adapter plate varies depending on the speaker system. Model F-03BT F-03WT F-05BT F-05WT F-08BT F-08WT Adapter plate HY-F03B HY-F03W HY-F05B HY-F05W HY-F08B HY-F08W [Example of a ceiling installation] Ceiling Speaker ceiling mount (K&M) Adapter plate* (option) [Example of a speaker stand installation] Speaker Speaker Adapter plate* (option) Adapter (K&M) ST-34B (option) 19 9. SPECIFICATIONS 9.1. F-03BT, F-03WT Model No. Enclosure Power Handling Capacity*1 Rated Input Rated Impedance Sensitivity Frequency Response Directivity Angle Speaker Component Input Terminal Operating Temperature Installation Environment Finish Enclosure Grille Speaker bracket Base bracket Base bracket cover Dimensions Weight F-03BT F-03WT Bass-reflex type Rated noise power: 30 W (8 ) Continuous program: 60 W (8 ) 15 W (100 V line, 70 V line) 8 100 V line: 670 (15 W), 2 k (5 W), 3.3 k (3 W), 10 k (1 W) 70 V line: 330 (15 W), 670 (7.5 W), 2 k (2.5 W), 3.3 k (1.5 W), 10 k (0.5 W) 87 dB (1 W, 1 m) at installation in 1/2 free sound field 85 Hz 20 kHz, 10 dB at installation in 1/2 free sound field Horizontal: 100°, Vertical: 100° 9 cm (3.5") Full-range, PP cone-type Push-in terminal 10 to +50 °C (14 to 122 °F) Indoor installation HIPS, black*2, paint HIPS, white*3, paint Aluminum, black*2, paint Aluminum, white*3, paint Die-cast aluminum, black*2, paint Die-cast aluminum, white*3, paint Steel plate, t4, black*2, paint Steel plate, t4, white*3, paint HIPS, black*2 HIPS, white*3 130 (w) x 221 (h) x 132 (d) mm (5.12" x 8.7" x 5.2") 1.7 kg (3.75 lb) *1 Rated noise power is defined by IEC60268-5. Continuous program is 3 dB above Rated noise power. *2 RAL 9011 equivalent *3 RAL 9016 equivalent Note: The design and specifications are subject to change without notice for improvement. · Accessories Speaker bracket ............................................................................ 1 Base bracket .................................................................................. 1 Base bracket cover ........................................................................ 1 Machine screw M4 x 8 (with plain washer and spring washer) ..... 1 Machine screw M5 x 20 (with plain washer and spring washer) ... 2 Flange nut for M8 .......................................................................... 1 20 9.2. F-05BT, F-05WT Model No. Enclosure Power Handling Capacity*1 Rated Input Rated Impedance Sensitivity Frequency Response Crossover Frequency Directivity Angle Speaker Component Input Terminal Operating Temperature Installation Environment Finish Enclosure Grille Speaker bracket Base bracket Base bracket cover Dimensions Weight F-05BT F-05WT Bass-reflex type Rated noise power: 60 W (8 ) Continuous program: 120 W (8 ) 30 W (100 V line, 70 V line) 8 100 V line: 330 (30 W), 1 k (10 W), 3.3 k (3 W), 10 k (1 W) 70 V line: 170 (30 W), 330 (15 W), 1 k (5 W), 3.3 k (1.5 W), 10 k (0.5 W) 90 dB (1 W, 1 m) at installation in 1/2 free sound field 60 Hz 20 kHz, 10 dB at installation in 1/2 free sound field 4.5 kHz Horizontal: 100°, Vertical: 100° Low frequency: 13 cm (5") PP cone-type High frequency: 25 mm (1") dome tweeter Push-in terminal 10 to +50 °C (14 to 122 °F) Indoor installation HIPS, black*2, paint HIPS, white*3, paint Aluminum, black*2, paint Aluminum, white*3, paint Die-cast aluminum, black*2, paint Die-cast aluminum, white*3, paint Steel plate, t4, black*2, paint Steel plate, t4, white*3, paint HIPS, black*2 HIPS, white*3 162 (w) x 274 (h) x 164 (d) mm (6.38" x 10.79" x 6.46") 2.7 kg (5.95 lb) *1 Rated noise power is defined by IEC60268-5. Continuous program is 3 dB above Rated noise power. *2 RAL 9011 equivalent *3 RAL 9016 equivalent Note: The design and specifications are subject to change without notice for improvement. · Accessories Speaker bracket ............................................................................ 1 Base bracket .................................................................................. 1 Base bracket cover ........................................................................ 1 Machine screw M4 x 8 (with plain washer and spring washer) ..... 1 Machine screw M5 x 20 (with plain washer and spring washer) ... 2 Flange nut for M8 .......................................................................... 1 21 9.3. F-08BT, F-08WT Model No. Enclosure Power Handling Capacity*1 Rated Input Rated Impedance Sensitivity Frequency Response Crossover Frequency Directivity Angle Speaker Component Input Terminal Operating Temperature Installation Environment Finish Enclosure Grille Speaker bracket Base bracket Base bracket cover Dimensions Weight F-08BT F-08WT Bass-reflex type Rated noise power: 90 W (8 ) Continuous program: 180 W (8 ) 60 W (100 V line, 70 V line) 8 100 V line: 170 (60 W), 330 (30 W), 670 (15 W), 3.3 k (3 W), 70 V line: 83 (60 W), 170 (30 W), 330 (15 W), 670 (7.5 W), 3.3 k (1.5 W) 91 dB (1 W, 1 m) at installation in 1/2 free sound field 50 Hz 20 kHz, 10 dB at installation in 1/2 free sound field 3 kHz Horizontal: 100°, Vertical: 100° Low frequency: 20 cm (8") PP cone-type High frequency: 25 mm (1") dome tweeter Push-in terminal 10 to +50 °C (14 to 122 °F) Indoor installation HIPS, black*2, paint HIPS, white*3, paint Aluminum, black*2, paint Aluminum, white*3, paint Die-cast aluminum, black*2, paint Die-cast aluminum, white*3, paint Steel plate, t4.5, black*2, paint Steel plate, t4.5, white*3, paint HIPS, black*2 HIPS, white*3 251 (w) x 392 (h) x 216 (d) mm (9.88" x 15.43" x 8.5") 5.2 kg (11.46 lb) *1 Rated noise power is defined by IEC60268-5. Continuous program is 3 dB above Rated noise power. *2 RAL 9011 equivalent *3 RAL 9016 equivalent Note: The design and specifications are subject to change without notice for improvement. · Accessories Speaker bracket ............................................................................ 1 Base bracket .................................................................................. 1 Base bracket cover ........................................................................ 1 Machine screw M4 x 8 (with plain washer and spring washer) ..... 1 Machine screw M5 x 20 (with plain washer and spring washer) ... 2 Flange nut for M10 ........................................................................ 1 22 https://www.toa-global.com/en 133-01-00359-00