Installation Guide for Rosewill models including: RMS-P61U, RMS-P61U_A, RMS-P61U Monitor Desk Mount, Monitor Desk Mount, Desk Mount
Rosewill Premium Single Monitor Mount, 13 to 35 Inch, 0 to 26.5lbs, Ultrawide Computer Monitor Stand for 35 inch Screens, Upgraded Adjustable Monitor Mount with USB, C-Clamp & Grommet Base, VESA 75x75 - Newegg.com
Rosewill Premium Single Monitor Mount, 13 to 35 Inch, 0 to 26.5lbs, Ultrawide Computer Monitor Stand for 35 inch Screens, Upgrad
File Info : application/pdf, 6 Pages, 24.70MB
DocumentDocumentUSB Expansion Function
RMS-P61U
Thank you for purchasing a Rosewill Monitor Desk Mount. Please read the instruction manual before use and retain for future reference.
13" - 35" Tilt +90°/-85°
Load 0-12kgs/0-26.4lbs
VESA 75x75, 100x100
Swivel 180°
Rotate 360°
RMS-P61U_A
Installation INSTRUCTIONS
11
WARNING STATEMENTS
Warning
Prior to the installation of this product, the installation instruction must be read and completely understood. Failure to do so may result in personal injury, property damage or voiding of factory warranty.
Do not install on a structure that is prone to vibration, movement or chance of impact. Reinforce the structure as required before installation. Make sure that the edge of table top is load-bearing enough.
The desk clamp can support a maximum thickness of 8 cm. Confirm the desk edge before installation.
Pay attention to the weight capacity of the mount. Exceeding the limitation can result in function unworkable or even serious personal injury and property damage.
Never operate the mount if parts are missing or damaged. Please contact our customer service team.
PRODUCT LINE GRAPH
360
90 360
85 180
185-510mm/7.3-20.1"
01
Step 8: Cable Management Installation
Loosen
1 2
3 Organize cables using the clips in the upper arms. Pull the lower cover out as shown, run cables through the lower arms and reattach the covers.
10
Step 7: Tilt & Swivel & Rotation Adjustment
VESA Swivel Adjustment S=5mm
+
S=5mm
D
VESA Tilt Adjustment S=5mm
+
Desk
This function works better for monitor with the center of gravity.
Use a 5mm hex wrench to adjust the damp for Tilt , Swivel and Rotation. Turn counter-clockwise to reduce damping and clockwise to increase damping.
09
TOOLS REQUIRED NOT INCLUDED
PARTS INCLUDED
A
M4x12 (x4) M4x30 (x4) 12X5.8X16 (x4)
B
M8x35 (x1) M8 (x1) 25.4X8.2X1.5 (x1) 16X8.2X1.5 (x1)
C
M4x10 (x1)
M6x12 (x4)
S=3mm (x1)
S=4mm (x1)
S=5mm (x1)
D
(x1)
a (x1) Base
b (x1) Clamp
c (x1) VESA Plate
d (x1) Head
e (x1) Gas Spring Arm
f (x1) Lower Arm
02
Step 1: Clamp Installation
M6x12
S=4mm S=5mm
C
D
D
S=5mm
M6x12
S=4mm
S=5mm
S=5mm
Falls Down
S=5mm
D
Problem After being attached to the arm, the monitor falls down and can not stay at the desired height by itself. Solution
Turn counter-clockwise("+" direction) to increase gas spring tension until the monitor can stay at the desired height by itself.
Rises up
Problem After being attached to the arm, the monitor rises up and can not stay at the desired height by itself. Solution
Turn clockwise("-" direction) to reduce gas spring tension until the monitor can stay at the desired height by itself.
Step 6 Rotation Restriction
Adjust the Clamp width to fit with desk. Secure stand to desktop by tightening Clamp. After this step,then Step 2 on Page 5.
03
Please do not move stand outside desk for safety
08
Step 4: Hang Monitor
M4x10
C
OR Step 1: Grommet Base Installation
S=5mm
D
Desk
NOTE: Hand tighten screws to avoid over tightening.
Slide the monitor onto the head of swivel arm, install the security bolt. Make sure the security bolt is installed before you rotate the monitor.
Step 5: Adjust Tension
S=5mm
D
S=5mm 1BSSNFTTUPEPBXIPOSUJI[PFO UBM QPTJUJPO
Desk
For proper functioning of this mount, depending on different weight of monitor you might need to adjust tension in the gas spring arm using 5mm hex wrench.
07
S=5mm
NOTE:If your desk has an existing grommet hole,remove plastic cover before installation. If there is no existing grommet hole,make a mark on your mounting surface,and use a drill to drill a hole (10-12mm) in the mounting surface.
04
Step 2 Arm Installation
S=3mm
D
S=3mm
Install the lower arm to the base. Secure the arm by tightening the inside screw using 3mm Allen key.
S=3mm
Desk
S=5mm
M8x35 16X8.2X1.5 25.4X8.2X1.5
M8
S=3mm S=5mm
D
M8x35
M8
25.4X8.2X1.5 16X8.2X1.5
B
Insert the gas spring arm above the lower arm and fasten the screw in the front.
05
Step 3 Attach Monitor OPTION A: For Flat Back Monitor
TOP OF Monitor
M4x12
A
NOTE: Hand tighten screws to avoid over tightening.
Flat surface installation:Install 4 short screws through faceplate to monitor via mounting holes.Do not tighten the screws excessively or your monitor might be damaged.
OPTION B: For Recessed/Curved Back Monitor
TOP OF Monitor
M4x30
A
12X5.8X16
A
NOTE: Hand tighten screws to avoid over tightening.
Recessed/Curved surface installation:Put 4 spacers between faceplate and monitor.Install 4 long screws through faceplate,spacers to monitor via mounting holes.Do not tighten the screws excessively or your monitor might be damaged.
06