Goobay Monitor Mount with Gas Spring

Safety Instructions

The user manual is part of the product and contains important information for correct use. Read the manual completely and carefully before use. Keep this manual. Do not modify the product or accessories. Use the product, parts, and accessories only in perfect condition. Contact your dealer or manufacturer for questions, defects, mechanical damage, or other problems not covered by the documentation. Not suitable for children or persons with limited physical or mental abilities. Secure packaging, small parts, and insulation against accidental use. Mounting, dismounting, care, storage, transport, and disposal should only be performed by users with basic mechanical knowledge. Have maintenance and repair work carried out only by qualified personnel. Avoid extreme stresses such as heat and cold, moisture, direct sunlight, microwaves, vibrations, and mechanical pressure. Place, install, and transport the product, parts, and accessories safely. When working with loads, ensure your safety and the work area, and get help from a second person. Do not install the product in places with direct sunlight or bright light, as this can cause eye fatigue. Be aware of the product's moving parts during use; they can pinch or squeeze limbs. Ensure sufficient space around the product and the system for proper ventilation and mobility. Compare the technical specifications of all products used; they must match or be within the specified range. Supporting surfaces must safely withstand the weight of the mount and attached equipment. Use only the provided mounting screws. Do not overtighten screws, as threads can be damaged.

Description and Function

Product

The product is a tiltable, rotatable, and swiveling table monitor holder with a gas spring for mounting screens up to 9 kg.

Scope of Delivery

Refer to Table 1 for the scope of delivery:

• Spring arm with monitor mount (A)
• Plate for screw clamp (B)
• Screw clamp (C)
• M6x12 (D)
• M6x10 (E)
• Insert (F)
• Mounting screw (G)
• Insert (H)
• Wing nut (I)
• Allen key 4 mm (J)
• Allen key 6 mm (K)
• M4x12 (M-A)
• M5x12 (M-B)
• Washer D5 (M-C)
• User Manual

Required Tools

Refer to Table 2 for required tools:

• Drill (1)
• Suitable drill bit (Ø 10.0 mm) (2)

Specifications

Intended Use

Use of the device in any way other than described in the "Description and Function" or "Safety Instructions" chapters is not permitted. This product is intended for use only in dry indoor rooms. Failure to comply with these regulations and safety instructions may result in serious accidents, injuries, and damage to persons and property.

Preparation

Check the scope of delivery for completeness and integrity.

Mounting

5.1 Unpacking the spring arm with monitor mount

Refer to Fig. 1. ⚠️ WARNING! Risk of injury from stored energy! The spring arm is under pressure and can suddenly extend if released too quickly. 1. Hold the spring arm firmly together on both sides and have another person cut the cable tie around the spring arm. 2. Slowly release the pressure and let the spring arm extend gradually to its full length.

5.2 Mounting on a table top

Preparation: See Fig. 2. For table tops 10-55 mm: See Fig. 3. For table tops 50-85 mm: See Fig. 4.

5.3 Mounting through a hole in the table

Preparation: See Fig. 5. For table tops 10-85 mm: See Fig. 6.

5.4 Attaching the monitor mount to the screen

Refer to Fig. 7. This step must be carried out by 2 people!

5.5 Balancing the spring arm

Refer to Fig. 8. ⚠️ CAUTION! Material damage! Always keep the spring arm in a horizontal position when making adjustments. If necessary, have another person help you. The spring arm must be properly balanced after the screens have been attached. Hold the spring arm in a horizontal position and adjust the spring tension with the Allen key (K). Do not overtighten the screws! A If the spring arm sinks, turn the adjustment screw counter-clockwise until it remains in a horizontal position. B If the spring arm rises, turn the adjustment screw clockwise until it remains in a horizontal position.

5.6 Using the cable glands

Refer to Fig. 9.

5.7 Adjusting the screen

Refer to Fig. 10. Set the desired angle and then tighten the screws alternately.

Maintenance, Care, Storage and Transport

Let maintenance and repair work only be carried out by qualified personnel. Protect the joints from dirt and grease them regularly with light machine oil. Use only a dry and soft cloth for cleaning. Use caution when cleaning to avoid scratches. In case of heavy soiling, the cleaning cloth can be slightly moistened with water. Do not use detergents or chemicals. Regularly check the tightness of the product/screws. Fixing holes may remain visible when the product is removed. After prolonged use, a stain may remain on the surface. Store the product out of reach of children and in a dry, dust-protected environment when not in use. Keep and use the original packaging for transport.

Disposal Instructions

This product does not belong in household waste. At the end of its working life, return it to the manufacturer, sales outlet, or designated public collection points free of charge. Disposal details are regulated by respective country laws. Recyclables are fed into the recycling circuit to obtain new raw materials. The following recyclable materials are collected at municipal collection points: Waste glass, plastics, scrap metal, sheets, and more. By recycling used equipment in this manner, you make an important contribution to protecting our environment.

Warranty

Detailed warranty conditions are available at www.mygoobay.com.

Symbols Used

✔️ For indoor use only (IEC 60417-5957)