User Guide for HOLMAN models including: CO6004 Quik Dial Tap Timer, CO6004, Quik Dial Tap Timer, Dial Tap Timer, Tap Timer
4 of 32 Overview Main Components 1. ZONE 1 outlet 2. ZONE 2 outlet 3. ZONE 3 outlet 4. ZONE 4 outlet Each outlet is 20mm BSP with 12mm snap‑on connection included 5. 20/25mm BSP tap nut inlet 6. Tap connection locking nut
File Info : application/pdf, 32 Pages, 2.67MB
DocumentDocumentDOWNLOAD THE LATEST MANUAL! User Guide Reliance Worldwide Corporation (Aust.) Pty. Ltd. 27-28 Chapman Place Eagle Farm, QLD, Australia 4009 PRODUCT CODE: CO6004 2 of 32 Contents Overview 4 Main Components 4 Additional Functions 5 Specifications 5 Precautions and Use 6 Setup 7 Battery Installation 7 Setup Process 8 Set Clock 12 Starts 13 Start Time 16 Run Time 17 Set Day 18 Zone 20 Conflicting Starts 22 Removal of All Zones from a Start 23 Operation 24 Automatic Watering 24 Manual Watering 25 Manual Watering 26 No/Suspended Watering Mode 27 Maintenance 28 Cleaning 28 Cold Weather 29 Batteries 29 Troubleshooting 30 3 of 32 Overview Main Components 1. ZONE 1 outlet 2. ZONE 2 outlet 3. ZONE 3 outlet 4. ZONE 4 outlet ® Each outlet is 20mm BSP with 12mm snapon connection included 5. 20/25mm BSP tap nut inlet 6. Tap connection locking nut 7. Display 8. ON/OFF 9. MENU DIAL ® Requires 4× AA alkaline batteries only (not included) 5 6 7 1 8 9 4 4 of 32 2 3 Overview (continued) Additional Functions ® Inactivity on your QuikDial Tap Timer controls for 25 seconds will return to the default system mode displaying the current time Á Removing the AA batteries will reset all clock and schedule settings ® To reset your QuikDial Tap Timer, remove the batteries for 2 minutes which will return the timer to factory default Á For use with cold water only Specifications 7 DAY SCHEDULING WATERING DURATION WORKING PRESSURE MAXIMUM FLOW RATE CONNECTIONS WORKING TEMPERATURE BATTERIES MonSun selection 199 minutes 301,200kPa 25 L/min 20/25mm BSP inlet / 20mm BSP outlet 3°C to 50°C 4× AA alkaline (not included) 5 of 32 Overview (continued) Precautions and Use Á Your QuikDial is designed to hang vertically from a tap Á Do not use in place of irrigation solenoids Á Use with caution on short run drip systems, these can keep valves open when they need to close. A pressure reducer is recommended 6 of 32 Setup Battery Installation 1. Install 4× 1.5V AA alkaline batteries into your QuikDial Tap Timer, as indicated in the battery compartment [a] a ® The timer screen will flash through ZONE I, ZONE II, ZONE III, ZONE IV as part of start up ® Once the startup process is complete, the CLOCK will display as follows, with the time separator flashing [b] and the battery indicated as full [c] b c 7 of 32 Setup (continued) Setup Process ® Your QuikDial has a simple and intuitive setup system quickly completed in 5 steps ® Your QuikDial has up to 4 START TIMES available ® RUN TIMES between 199 min per ZONE ® ZONES will water sequentially starting from the set START TIME ® 1 or all ZONES can be included in each START, for a total of up to 16 waterings (4 ZONES, 4 times per day) to be set ® As an example, if you set a START with a RUN TIME of 60 min this will give a total of 4 hours of watering when all four ZONES are included in the start ® For automatic watering, you must ensure that the CLOCK, START TIME, RUN TIME, SET DAY and ZONE have all been set correctly 8 of 32 Setup (continued) Setup Process ® Here is a quick overview to see how all these settings combine into a automated watering schedule for your garden ZONE Start Time 07:00 S 1 T A R Run Time 10min T Set Day Mo Tu We Th Fr Sa Su E N 10 0 D 0 10 min min min min ZONE I will start at 7:00 am, for a duration of 10 minutes, on Mondays and Tuesdays. When ZONE I stops, ZONE IV will start (at 7:10 pm) for the same duration (10 minutes). Start Time 07:00 S 1 T A R Run Time 10min T Set Day Mo Tu We Th Fr Sa Su ZONE 10 0 0 10 min min min min S 2T A R T Start Time 06:00 Run Time 15min Set Day Mo Tu We Th Fr Sa Su E N D 0 15 15 0 min min min min In addition to the START 1 cycle, START 2 will activate ZONE II at 6:00 am on Wednesdays for a duration of 15 minutes, followed by ZONE III for a duration of 15 minutes. Setup (continued) Setup Process Start Time 07:00 S 1 T A R Run Time 10min T Set Day Mo Tu We Th Fr Sa Su ZONE 10 0 0 10 min min min min S 2T A R T Start Time 06:00 Run Time 15min Set Day Mo Tu We Th Fr Sa Su 0 15 15 0 min min min min S 3T A R T Start Time 18:30 Run Time 20min Set Day Mo Tu We Th Fr Sa Su E N D 0 0 0 20 min min min min In addition to STARTS 1 and 2, START 3 will activate ZONE IV at 6:30 pm of 20 minutes on Mondays and Fridays 10 of 32 Setup (continued) Setup Process Start Time 07:00 S 1 T A R Run Time 10min T Set Day Mo Tu We Th Fr Sa Su ZONE 10 0 0 10 min min min min S 2T A R T Start Time 06:00 Run Time 15min Set Day Mo Tu We Th Fr Sa Su 0 15 15 0 min min min min S 3T A R T Start Time 18:30 Run Time 20min Set Day Mo Tu We Th Fr Sa Su 0 0 0 20 min min min min S 4T A R T Start Time 06:00 Run Time 15min Set Day Mo Tu We Th Fr Sa Su E N D 15 0 15 0 min min min min In addition to STARTS 1, 2 and 3, START 4 will activate ZONES I and III at 6:00 am for 15 minutes on Saturdays. 4× STARTS is the maximum available. 11 of 32 Setup (continued) Set Clock ® The current time and day of the week is needed as the reference point for your program to work ® The CLOCK is in 24hr time (12:00 is midday and 00:00 is midnight) 1. To set the clock, turn your MENU DIAL anticlockwise (left) or clockwise (right) until the time is flashing [a] 4. Press the MENU DIAL and the MINUTES will flash [c] c 5. Turn the MENU DIAL to select the MINUTES of the current time 6. Press the MENU DIAL and DAYS will flash [d] a 2. Press the MENU DIAL once and the HOUR will flash [b] b 3. Turn the MENU DIAL to set the HOUR of the current time d 7. Turn the MENU DIAL to select the current DAY of the week 8. Press the MENU DIAL to complete this step Setup (continued) Starts ® Your QuikDial has up to 4 START TIMES available, these can be used for 1 or both ZONES as needed ® There is a default time set for each START. To see these, turn the MENU DIAL clockwise (right) ® While START 1 is on, STARTS 2, 3 and 4 are set to OFF ® The START TIMES are in 24hr time ® 00:00 is midnight and 12:00 is midday ® Default START TIMES are as follows: L START 1--07:30 L START 2--09:30 L START 3--15:30 (3.30pm) L START 4--18:30 (6.30pm) 13 of 32 Setup (continued) Turn a Start On/Off ® Begin by turning the MENU DIAL clockwise (right) until you see the START NUMBER (1, 2, 3 or 4) you want to select ® If the START is OFF and you need to turn it ON: 1. Select the START NUMBER by turning the MENU DIAL 2. Press the MENU DIAL and a flashing ON will be displayed [a] 4. The START NUMBER will now flash [b]-- indicating you can now b move to the next start a 3. Press the MENU DIAL to confirm the START as ON 5. Turn the MENU DIAL to the next START and repeat the process to turn ON/ OFF the other STARTS 14 of 32 Setup (continued) Turn a Start On/Off ® If the START is ON and you need to turn it OFF: 1. Select the START NUMBER by turning the MENU DIAL 4. Press the MENU DIAL to confirm the start as OFF 2. Press the MENU DIAL once, a flashing menu box will appear around START TIME [c] 5. The START NUMBER will now flash [e]--this indicates you can now e move to the next START c 3. Turn the MENU DIAL anticlockwise (right) and a flashing OFF will be displayed [d] 6. Turn the MENU DIAL to the next START and repeat the process to turn ON/ OFF the other STARTS d 15 of 32 Setup (continued) Start Time ® START TIME is the time of day your watering begins ® Your QuikDial waters each ZONE sequentially starting from this time. ZONES are added at a later step-- c refer to ZONE setup instructions to learn more 3. Press the MENU DIAL once, the menu box around START TIME will flash [c] ® To set the watering START TIME for your active START/S: 1. Select the START NUMBER by turning the MENU DIAL b clockwise (right) 4. Press the MENU DIAL again and HOURS will flash [d], indicating HOURS can now be set 2. Active STARTS have the START NUMBER [a] and ON [b] displayed a on the screen b 5. Turn the MENU DIAL left or right to set to your preferred HOUR for the START TIME 16 of 32 Setup (continued) Start Time 6. Press the MENU DIAL again and the MINUTES will now flash [e] e 7. Turn the MENU DIAL left or right to set the MINUTES 8. Once the MINUTES are correct, press the MENU DIAL again to move on to RUN TIME Run Time ® RUN TIME is the watering duration for your START ® You can set 1 RUN TIME per START ® Min. RUN TIME is 1 min ® Max. RUN TIME is 99 min ® RUN TIME can be accessed two ways--either as a continuation from the START TIME, or using the following steps: 1. Turn the MENU DIAL to select the START NUMBER ® RUN TIME applies to each 2. Press the MENU DIAL, ZONE in the START and the menu box will flash ® As an example, if you set around START TIME [a] a RUN TIME of 60 min this will give a total of 4 hrs of watering a when all ZONES are included in the START Setup (continued) Run Time Set Day 3. Turn the MENU DIAL clockwise (right), and the menu box will now flash around RUN TIME [b] b 4. Press the MENU DIAL once and the RUN TIME will begin flashing [c] c 5. Turn the MENU DIAL to the desired RUN TIME (up to 99 min) 6. Press the MENU DIAL again to move on to SET DAY ® Your QuikDial allows you to select the days of the week to water Á There is no interval watering option ® The 7 days of the week are represented with their first two letters. MO for Monday, TU for Tuesday etc. ® SET DAY allows you to select (or change) the day/s you wish to water either as a continuation from the RUN TIME or using the following steps: 1. Turn the MENU DIAL to select the START NUMBER 2. Press the MENU DIAL 3. The menu box will flash around START TIME [a] 18 of 32 a Setup (continued) Set Day 4. Turn the MENU DIAL clockwise (right), until a box is flashing around SET DAY and lines are flashing below the days of the week [b] 6. Turn the MENU DIAL clockwise (right) to move to TU 7. Repeat for each day, pressing the MENU DIAL to remove days as needed b ® If a day is removed by accident, turn the MENU DIAL anticlockwise until the line is flashing under 5. Press the MENU DIAL once and a solid line will flash below MO only [c] the removed day. Press the MENU DIAL again to reinstate the day a. To keep MO selected, turn the MENU DIAL clockwise (right) to ® Only the days which are included in the START will be displayed move to the next day 8. Once you have set/removed b. To remove MO press the SU all lines will flash[d] MENU DIAL, MO will be removed from the screen d 9. Press the MENU DIAL again to move on to ZONE c 19 of 32 Setup (continued) Zone Á A START will remain OFF if no ZONES are selected for the START ® ZONES can be set up either with a separate START (when needed to water on different DAYS or different START TIMES), or set up within the same START ® All STARTS have ZONE I selected by default ® You can change to another ZONE or select all ZONES via the ZONE menu ® When ZONES are set to water within the same START your QuikDial will water each zone sequentially starting from the set START TIME ® ZONE can be accessed two ways--either as a continuation from the SET DAY, or using the following steps: 1. Turn the MENU DIAL to select the START NUMBER 2. Press the MENU DIAL 3. The menu box will flash around START TIME 4. Turn the MENU DIAL clockwise (right) until a box is flashing around ZONE [a] a 5. Press the MENU DIAL to confirm you'd like to update the ZONE menu Setup (continued) Zone 6. ZONE I will flash [b] b 7. Turn the MENU DIAL clockwise (right) and ZONE II [c] will flash c ® Pressing the MENU DIAL once when the ZONE is flashing will allow you to select or delete the ZONE from the START ® As ZONE I is already programmed to water during this START, you can: a. Move onto step 7 to keep ZONE I selected b. Press the MENU DIAL to remove ZONE I from the START ® As ZONE II is not programmed to water during this START, you can: a. Press the MENU DIAL to select ZONE II for the START b. Turn the MENU DIAL clockwise (right) and repeat for zones III and IV as needed 21 of 32 Setup (continued) Conflicting Starts Á If more than one START has been set with the same START TIME and SET DAYS, the timer will ignore the duplication. Only the first start will be run in these cases ® Use the 4 available STARTS to spread out your watering needs--avoiding conflicting STARTS 22 of 32 Setup (continued) Removal of All Zones from a Start Á A START will not allow you to turn it ON until a ZONE is selected for the START ® If any active (ON) START/S have all ZONES deselected and turned off, you will need to add a ZONE back to restore the START 1. To restore the ZONE/S, turn the MENU DIAL to select the START NUMBER 2. Press the MENU DIAL 3. A box will flash around START TIME 4. Turn the dial anticlockwise (left) until you enter ZONE selection, a box will flash around ZONE--refer to step 5 in ZONE setup instructions to continue to restore ZONES 23 of 32 Operation Automatic Watering ® Ensure CLOCK, START TIME, RUN TIME, SET DAY and ZONE have all been set correctly 1. When the CLOCK [a] and START TIME [b] match, the ZONE/S will start watering in sequential order ® Pressing the ON/OFF button 2. During watering, the during an automatic program sprinkler animation [c] will stops it from watering be active and the current ® After 25 seconds of inactivity on your ZONE [d] will flash d e c QuikDial controls, the set watering schedule will be active in the background as per your confirmed settings ® In this state, your QuikDial display will cycle between the CLOCK [a] and the START TIME of your next watering session [b] a ® Additional zones scheduled for watering will also show [e] ® Your timer will have a three second period of 00 before ending a watering or moving to the next ZONE b Operation (continued) Manual Watering ® By default, the preset manual RUN TIME is 5 min 1. For manual (instant) watering, press ON/OFF 2. ZONE I will flash [a], turn the MENU DIAL to select a ZONE a ® During watering, the sprinkler animation will be active [c] and the selected ZONE [d] will flash d c 3. Press the MENU DIAL to confirm your ZONE selection 4. To water for the preset manual RUN TIME, wait a short period of time for the RUN TIME to stop flashing [b], indicating it has been set b 5. To adjust the manual RUN TIME, turn MENU DIAL when the RUN TIME is flashing [b] b ® Min. manual RUN TIME is 1 min ® Max. manual RUN TIME is 99 min 25 of 32 Operation (continued) Manual Watering 6. Press the MENU DIAL to confirm your selection 7. After a short period of time, the RUN TIME will stop flashing to indicate it has been set ® If the RUN TIME stops flashing before you were able to adjust it--press ON/OFF to stop watering and restart the MANUAL WATERING process from step 1 ® To stop watering before the remaining time has lapsed, press ON/OFF and your QuikDial will return to the default display 26 of 32 Operation (continued) No/Suspended Watering Mode 1. To stop all automatic watering, press the MENU DIAL for 3 seconds 2. The display will enter NON WATERING MODE [a] 3. To return to scheduled automatic watering, press the MENU DIAL for 3 seconds 4. The NON WATERING ICON will disappear and your a automated watering will continue 27 of 32 Maintenance Cleaning ® Check and clean your filter washer at least twice a year ® Debris can be removed with a soft toothbrush and suitable cleaner where needed (white vinegar/CLR) ® Damaged filters/washers should be replaced ® In hard water areas, further cleaning may be required after periods of no use--as minerals will set in the body of the timer 1. Remove all tap fittings and the neck assembly from the timer 2. Your timer will need to be stable and upright--an egg carton (or similar) may assist with this 5. Turn the timer upside down and repeat this on each outlet (fill outlet with solution, allow to sit, empty and rinse well) Á Do not immerse your timer in cleaning solution 3. Make a 50/50 white vinegar and water solution--pour this into the top of your timer 4. Allow it to sit for 10 min then empty the timer and rinse well 28 of 32 Maintenance (continued) Cold Weather ® Your QuikDial should be removed from the tap and stored away during winter Á Keep your QuikDial out of freezing conditions as this can damage internal components Batteries ® Remove batteries from your QuikDial during periods of nonusethis will erase all settings Á Battery leakage can cause corrosion and damage to your QuikDial Á Please only use quality alkaline batteries in your tap timer Á Do not mix old and new batteries Á Do not use rechargeable batteries 29 of 32 Troubleshooting Question Why won't my timer stop watering? Answer n If your QuikDial Tap Timer is installed on a short run or pressure compensating system, there can be issues with the valve closing n This is due to more water on offer than can exit the system-- creating a pressure differential n This can be mitigated using a pressure reducer n Your timer may have a blockage preventing the valve from closing contact customer service at support@holmanindustries.com.au for assistance Why is there no water coming into the system? n Check if the filter is clogged, clean if required--refer to Cleaning for more information n Check for blockages in the sprinkler/ emitter, clean if required n There may be an airlock--remove your timer from the tap and give it a shake to displace the airlock The Holman website has a host of additional information on features. Head to support.holmanindustries.com.au for more tips, tricks and support content. If you still need help, feel free to email our friendly Customer Service team at support@holmanindustries.com.au. 30 of 32 31 of 32 Thanks for being a #SMARTGARDENER We really appreciate having you as a customer, and would like to say thank you for choosing us. We recommend registering your new product on our website. This will ensure we have a copy of your purchase and activate an extended warranty. Keep up to date to with relevant product information and special offers available through our newsletter. www.holmanindustries.com.au/product-registration/ Copyright © 2024 Holman Industries