User Manual for Joylux models including: MA-TW01, MATW01, 2ASF2MA-TW01, 2ASF2MATW01, KT-LT01MB, Smart Light Bars
Shenzhen Linklite Smart Lighting Co., Ltd MA-TW01 Smart Light Bars 2ASF2MA-TW01 2ASF2MATW01 ma tw01
Smart Light Bars User Manual Model: KT-LT01MB Package Contents x2 x2 x2 x1 Smart Light Bars Light Bars Base Type C-C Cable USB A-A cable OUT R OUT L POWER Smart Light Bars User Manual MIC x1 x1 x1 MODE External Power Supply DATA DATA DC IN Control box Model: KT-LT01MB User Manual Specifications Power input (AC adapter) Tower 1 Tower 2 Dimensions Water Resistance Control Method Luminous power WiFi Bluetooth Operating Frequency Support System AC100-240V DC12V1A White diffuser silicone, aluminum post and base, 38 RGB LEDs White diffuser silicone, aluminum post and base, 38 RGB LEDs 376mm x 70mm x 70mm (without the headset holder) IP20 App, Control Box 11W IEEE 802.11 b/g/n 4.0 2.412~2.484GHz Android 5.0 or iOS 9.0 and above Special Note The lamp post is connected with the base according to the schematic diagram Front Back Left light bar signal output Right light bar signal output Type C-C Cable Type C-C Cable OUT R OUT L POWER Power button MIC Mode selection button MODE DATA DATA DC IN HDMI sync box data transmission interface Power input interface Power Mode Press on/off button Long press the power button for 5 seconds to start the network distribution. Press mode button switch the Smart Light Bars Light mode. Installing Steps 1. Remove Light bars from Starter Kit box. 2. Use the type c-c cable to connect the OUT L and OUT R of bars. 3. Insert power supply to DC IN. 4. Press power button start the smart light bars. How to distribution network: Preparation 1.Connect to 2.4GHz Wi-Fi network and turn Bluetooth on from you mobile phone. 2. Install the "Smart life" app from the Apple Store / Google Play Store. 3. Register an account and allow the app to use Bluetooth. Prepare the control box Connection 1. Charge and turn on power button of contor box. Smart Light Bars 2. The indicator will flash quickly in green. Breathing flashing Power Add the control box to Smart Life The lamp will appear automatically waiting to be added when you open the Smart Life App. 1. Click "Go to add". 2. Select the contor box. 3. Enter 2.4GHz Wi-Fi network name and password, then tap "Next". 4. You can edit the contor box name and click "Done" Customer Service Warranty: Support: Email: Official Website: FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Non-replaceable light source. Not intended for illumination. Only used for creating ambiance. 1. Do not connect the rope light to the supply while it is in the packing or wound onto a reel; 2. Do not use the rope light when covered or recessed into a surface; 3. Do not open or cut the rope light Frequency 2.4GHz Maximum Power<30dBm NOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates uses and can radiate radiofrequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If thisequipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Adobe PDF library 15.00 Adobe Illustrator(R) 17.0