Minelab ML 100 Bluetooth Headphones User Manual

Package Contents

• ML 100 Headphones
• 3.5 mm (1/8 inch) Detachable Auxiliary Cable
• USB Charging Cable
• Instruction Manual

Getting Started

1. Ensure the Bluetooth headphones are fully charged.
2. Pair the charged Bluetooth headphones with a Bluetooth-enabled device.

Buttons and Indications

Illustration shows the top and side view of the ML 100 headphones. On the right earcup, there are six numbered controls and sockets: 1. Volume Plus Button (+), 2. Multi-Function Button (MFB), 3. Volume Minus Button (-), 4. Status LED, 5. USB Micro-B Charging Socket, 6. Headphone Socket (3.5 mm).

Button Functions

• 1. VOLUME PLUS BUTTON (➕): Increases the volume by one level, plays the next track (?).
• 2. MULTI-FUNCTION BUTTON (MFB): Turns the headphones on or off, plays and pauses music (?), activates Pairing Mode (?), resets the headphones to factory defaults.
• 3. VOLUME MINUS BUTTON (➖): Decreases the volume by one level, plays the previous track (?).

Status LED Indicators

Sockets

• 5. USB MICRO-B CHARGING SOCKET: For charging the headphones (?).
• 6. HEADPHONE SOCKET: 3.5 mm (1/8 inch) for auxiliary cable connection (?).

Charging the Headphones

Connect the USB charging cable to the USB charging socket 5. The Status LED 4 will remain solid red (?) during charging. When charging is complete, the Status LED 4 will turn solid blue (?).

Note: USB Charger is not supplied. Any generic high-quality USB charger can be used.

Turning On/Off the Headphones

Turning On

Press and hold the MFB 2 until the Status LED 4 flashes solid blue (?) for 1 second, then flashes blue with an ascending 'beep' (?) sound. The headphones enter pairing mode automatically when no device is paired.

Turning Off

To turn off the ML 100 headphones, press and hold the MFB 2 for 2 seconds until the Status LED 4 flashes red (?). A series of descending tones will sound, and the headphones will turn off.

Pairing to a Detector

1. Place the headphones and the detector no more than 1 metre (3 feet) apart.
2. Ensure the headphones are turned off.
3. Press and hold the MFB 2 until a double ascending tone (??) is heard and the Status LED 4 flashes red and blue (??).
4. Press and hold the wireless button on the detector for 3 seconds. The Bluetooth icon (?) on the detector display will flash rapidly.
5. When pairing is complete, the headphones will beep (?) and the Status LED 4 will flash blue 3 times repeatedly (???), indicating connection to the detector.

Note: If pairing cannot be completed within 5 minutes after activation, the headphones will automatically enter Standby Mode (⏳).

Note: ML 100 headphones can be paired with two devices simultaneously, allowing pairing with both your detector and your smartphone.

Connect with the Last Paired Device

The headphones will automatically connect with the last-paired device. If connection is successful, the Status LED 4 will flash blue 3 times repeatedly (???).

Reset to Factory Defaults

Ensure the headphones are turned off. Press and hold the MFB 2 for approximately 10 seconds until two beeps (??) are heard and the Status LED 4 flashes pink 2 times (??). Release the button. The Status LED 4 will now flash red and blue (??), indicating pairing mode. All previously paired devices will be unpaired.

Music Functions

Play / Pause Music

Press the MFB 2 to pause/play music on your connected device. When music is playing, the Status LED 4 will flash blue 3 times repeatedly (???).

Next / Previous Track

Long press the Volume + button 1 for 2 seconds to play the next track (➡️). Long press the Volume - button 3 for 2 seconds to play the previous track (⬅️).

Adjust the Volume

Press the Volume + button 1 once to increase the volume by one level. Press the Volume - button 3 once to decrease the volume by one level. When maximum or minimum volume is reached, a high or low tone (?) will sound.

Connecting the Auxiliary Cable

The ML 100 headphones include a detachable 3.5 mm (1/8 inch) auxiliary cable for wired operation. This allows use if the battery is flat or with devices lacking Bluetooth capability.

To use the cable, plug the connector into the headphone jack 6 and turn 90° anti-clockwise to lock it. This prevents accidental disconnection.

Safety Information

• Check local laws regarding the use of smartphones and headphones whilst driving.
• If using headphones whilst driving, ensure your attention remains on the road and you drive responsibly and safely.
• Never allow children to play with the headphones; small parts are a choking hazard.
• Observe signs requiring electrical or RF radio products to be switched off in designated areas (e.g., hospitals, blasting areas, potentially explosive environments).
• Turn off headphones before boarding an aircraft.
• Never mount or store headphones over any air bag deployment area, as serious injury may result if the air bag deploys.
• Do not open or mutilate the built-in battery.
• Dispose of batteries according to local regulations; do not dispose as household waste.
• Only charge the headphones' built-in battery according to the instructions in this user guide.
• Avoid charging the headphones in extreme temperature conditions.

Care and Maintenance

• Turn the headphones off before placing them in a pocket or bag. If the MFB 2 is accidentally activated, your smartphone may place an unintended call if paired.
• Do not expose the headphones to liquid, moisture, or humidity, as they are not waterproof.
• Do not use abrasive cleaning solvents to clean the headphones.
• Do not expose the headphones to extreme temperature conditions.
• Do not dispose of the headphones in a fire, as this may result in an explosion.
• Do not bring the headphones into contact with sharp objects, as this will cause scratches and damage.
• Do not attempt to disassemble the headphones, as they do not contain serviceable components.
• If the headphones are not used for long periods, store them in a dry place free from extreme temperature conditions and dust.

Troubleshooting

If you are unable to connect your headphones to your device, try the following:

• Ensure your headphones are turned on and fully charged.
• Ensure the headphones are paired with your device.
• Ensure your device's Bluetooth feature is activated. Refer to your device's user guide for specific instructions.
• Ensure the headphones are within 10 metres (32 feet) of your device and there are no obstructions (e.g., walls, other electronic devices) in between.

Modification

Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the device.

(French: Toute modification non approuvée explicitement par le fournisseur de licence de l'appareil peut entraîner l'annulation du droit de l'utilisateur à utiliser l'appareil.)

FCC and Industry Canada Statements

This device complies with Part 15 of the FCC Rules and with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

(French: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage; (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.)

Simplified EU Declaration of Conformity

Hereby, Minelab Electronics Pty Ltd declares that the radio equipment type ML 100 complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.minelab.com/compliance.

Product Specification

Minelab reserves the right to introduce changes in design, equipment, and technical features at any time without notice. For the most up-to-date specifications, visit www.minelab.com.

MINELAB® is a trademark of Minelab Electronics Pty. Ltd. Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.