AETEK D62-040-30 L2 PRO Gigabit PoE Switch
Quick Installation Guide
Model: D62-040-30
P/N: 5019039600
Description: 4xGbE 30W PoE + 1xGbE bt PoE PD RJ45 + 2x24VDC output + 2x12VDC output Managed Switch
Introduction
The D62-040-30 is a 4-port 10/100/1000BaseT PoE switch capable of supplying 15.4/30W (54Vmax. per port) power to Power over Ethernet (PoE) devices.
Package Contents
- 1x PoE switch
- 1x DB9F-RJ45 console cable
- 1x Quick Installation Guide
- 1x DIN rail bracket
- 6 x 2-pin terminal block
Important Notes
- To prevent potential damage, ensure that all 12VDC, 24VDC, and Digital Input/Output (DI/DO) devices are properly connected before applying or turning on the DC input power. Connecting these devices after the power is on may result in malfunction or damage.
- Install the switch in a ventilated and dry place that is free of electromagnetic sources, vibration, moisture, and dust.
- Make sure the ventilation openings on the switch are not blocked.
- Supports bt PoE input.
- Digital output: ON/OFF, supports 5VDC/1A. Digital input: level 0 (Low), level 1 (High).
Connection
A diagram shows the connection between the D60-044-91 and the D62-040-30 switches, with a '90W bt PoE' cable linking them. The D62-040-30 features multiple ports and indicators.
Port Descriptions
- A: 10/100/1000 bt PoE PD RJ45 port
- B: 10/100/1000 PoE RJ45 ports (four ports)
- C: Console port
- D: SYS LED
- E: 12V2 / 12V1 / 24V2 / 24V1 LED
- F: Reset button
- G: Power LED
- H: 24VDC output ports (two ports)
- I: 12VDC output ports (two ports)
- J: DI / DO ports
- K: GND (Ground connection)
DIN Rail Installation
The switch can be mounted onto a standard DIN rail using its integrated mounting brackets. A visual guide shows the switch clipping onto the rail.
DI/DO Connection Diagrams
Two diagrams illustrate DI/DO connections. One shows a simple 5VDC device connected to the switch's DI/DO ports. The second diagram shows a similar setup but includes a 5V Relay controlled by the switch's DO ports, which in turn controls an AC or DC device.
Defaults
| Setting | Value |
|---|---|
| IP Address | 192.168.1.1 |
| Subnet Mask | 255.255.255.0 |
| User Name | admin |
| Password | admin |
LED Indicators
Power LEDs
| LED | Color | State | Description |
|---|---|---|---|
| Power | Amber | On | Powered on correctly. |
| Power | Off | Not receiving power from power1. |
Console Port Defaults
| Setting | Value |
|---|---|
| Baud rate | 115200 |
| Stop bits | 1 |
| Data bits | 8 |
| Parity | N |
| Flow control | none |
Port Status LEDs
| LED | Color | State | Description |
|---|---|---|---|
| RJ45 Ports Up (PoE) | Amber | On | The port is enabled and supplying power to connected device. |
| Off | The port has no active connection, or it is not connected to a PoE PD device. Otherwise, the port may have been disabled through the switch user interface. | ||
| RJ45 Ports Down (LAN) | Green | On | The port is enabled and established a link to connected device. |
| Green | Blinking | The port is transmitting/receiving packets. | |
| RJ45 Ports Down (LAN) | Off | The port has no active network connection, or it has no established link to connected device. Otherwise, the port may have been disabled through the switch user interface. |
Reset Button
| Task | Method | SYS LED Behavior | Port Status LED Behavior |
|---|---|---|---|
| Reset | Press 2~7 seconds | Blinking Green | All LEDs Off. |
| Restore Defaults | Press 7~12 seconds | Blinking Green | All LEDs On. |
Montreal Managed Services | Managed IT Services | Quesys MSP
