CONDTROL SCAN Electrical Wiring and Hardware Scanner
User Manual
Introduction
Optimal working with the instrument is possible only when the operating instructions and information are read completely, and the instructions contained therein are strictly followed. SAVE THESE INSTRUCTIONS.
Intended Use
The CONDTROL SCAN is intended for detection of metals (ferrous and non-ferrous metals, e.g., rebar), wooden joists, and “live” wires/conductors in walls, ceilings, and floors.
Package Contents
- 1 Instrument
- 1 Carry pouch
- 1 Power supply
- 1 User manual
Product Description
The CONDTROL SCAN is a handheld device for detecting various materials within walls, ceilings, and floors. Its front features a digital display and control buttons. The rear houses the battery compartment.
Key Components:
- LED indicator
- Display
- Wood detection button
- Metal detection button
- Live wires detection button
- Digital vial button / Sound signal toggle
- Instrument power on/off / Exit digital vial mode button
- Sensor area (located on the bottom of the device)
- Battery cover (located on the back)
Display Indicators and Icons:
- Battery charge level indicator ?
- Sound signal indicator ?
- Metal detection mode icon [Metal Mode]
- Wood detection mode icon [Wood Mode]
- Live wires detection mode icon [Live Wire Mode]
- Ferrous metal icon [Ferrous Metal] (symbol U)
- Non-ferrous metal icon [Non-ferrous Metal] (symbol Copper)
- Detected object approximation degree (0-100%) [Progress Indicator]
- Metal detection depth (cm) [Depth Indicator]
- Detection of object center [Center Indicator]
- Digital vial mode [Digital Level Indicator]
Technical Specifications
| Specification | Value |
|---|---|
| Maximum scanning depth* | |
| Ferrous metals | 100 mm |
| Non-ferrous metals (copper) | 80 mm |
| Copper conductors (live)** | 50 mm |
| Wood | 20 mm |
| Automatic shutdown | 5 min |
| Operating temperature | -10 °C ... +50 °C |
| Storage temperature | -20 °C ... +70 °C |
| Power supply | 1 x 9 V 6LR61 (alkaline) |
| Operating lifetime | Approx. 6 h |
| Dimensions | 196*76*25 mm |
| Weight | 0.145 kg |
* Depends on material and size of objects, as well as material and condition of structure.
** Less scanning depth for wires/conductors that are not "live".
Operation
Inserting/Replacing Battery
Remove the battery cover. Insert the 9 V alkaline battery, observing correct polarity. Replace the battery cover. Remove batteries if the product is not used for a long time to avoid corrosion and depletion.
Start Operation
Protect the instrument from moisture and direct sunlight. Ensure the sensor area is dry before switching on. If the instrument was subject to extreme temperature changes, allow it to acclimatize. To switch on, press and hold [Button 7] for 2 seconds. The instrument will automatically enter metal detection mode. If a sound signal is emitted and the red light indicator blinks, calibration is required: place the instrument in an environment free from metal and strong magnetic fields (e.g., hold it in the air), then press and hold [Button 7] until the green light indicator is on and a beep is heard. Calibration is finished. To switch off, press and hold [Button 7] for 2 seconds. The product will automatically shut off after 5 minutes of inactivity to save battery power.
Operating Modes
The instrument detects objects using the sensor area.
Detection of Metal Objects
Press [Button 4] to activate metal detection mode. The [Metal Mode] icon will appear on the display, and the green light indicator will be on. Move the instrument sideways across the surface. As it approaches a metal object, the detected object approximation degree (0-100%) increases, the light indicator turns yellow, then red, and a sound signal is emitted. As it moves away, the degree decreases, the light turns yellow then green, and the sound stops. If a metal object is directly below the sensor center, the [Center Indicator] and the metal detection depth (in cm) will be displayed. The accuracy of depth depends on object shape and location. For ferrous metals (e.g., steel), the [Ferrous Metal] icon (U) appears. For non-ferrous metals (e.g., copper), the [Non-ferrous Metal] icon (Copper) appears.
Detection of Wooden Objects
Press [Button 3] to activate wood detection mode. Place the instrument on an even surface, press and hold [Button 3] until the light indicator turns green (calibration finished). Move the instrument across the surface. As it approaches a wooden object, the detected object approximation degree (0-100%) increases, the light indicator turns yellow, then red, and a sound signal is emitted. As it moves away, the degree decreases, the light turns yellow then green, and the sound stops. If a wooden object is directly below the sensor center, the [Center Indicator] appears. Caution: If a wooden object is coincidentally located, the light indicator may turn red and emit a sound signal. In such cases, reposition the instrument and scan again.
Detection of Live Wires
Press [Button 5] to activate live wires detection mode. If a sound signal is emitted and the red light indicator blinks, perform calibration as described for metal detection. The instrument can detect live AC wires/conductors (40-60 Hz). Other wires are detected as metal objects. The [Live Wire Mode] icon (⚡) appears when a live wire is detected. Move the instrument repeatedly to pinpoint the wire. A red light indicator and sound signal indicate proximity (100% approximation). Static electricity can cause inaccurate results; place a free hand on the wall next to the instrument to mitigate its effect.
Digital Vial
Press [Button 6] to activate the digital vial function. Readings are shown on the display. Press [Button 7] to exit.
Switch On/Off Sound Signal
Press and hold [Button 6] to toggle the sound signal. The [Sound signal indicator] (?) appears on the display when the sound is on.
Recommendations for Use
Measurement accuracy can be affected by ambient conditions such as proximity to equipment producing strong magnetic/electromagnetic fields, moisture, metallic building materials, foil-laminated insulation, or conductive wallpaper. Consult additional information sources (e.g., construction plans) before drilling, sawing, or routing into walls, ceilings, or floors.
Care and Maintenance
- Wipe away debris or contamination with a dry, soft cloth. Do not use cleaning agents or solvents.
- To avoid affecting measurement function, do not place decals, stickers, or name plates (especially metal ones) on the sensor area.
- Store and transport the instrument only in the supplied protective case.
Warranty
The warranty period is 12 months from the date of sale. It covers all costs for repair or replacement of the device, excluding transportation costs to the service center. The warranty does not cover damages from misuse, unauthorized repair, blows, falls, or issues with batteries and accessories. Calibration expenses after repair are paid separately. CONDTROL is not responsible for loss of profits or inconvenience due to instrument defects, or costs for alternative equipment lease during repair. Instrument service life is 36 months.
Service
For service center contacts and consultation, visit the CONDTROL website: www.condtrol.com.
Utilization and Disposal
Expired instruments, accessories, and packaging should be sorted for environmentally friendly recycling according to local laws. Do not dispose of batteries in household waste, fire, or water. Collect and pass batteries for recuperation or environmentally friendly disposal. For EC countries: Do not dispose of the product in household waste. Follow European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment. Defective batteries must be recycled according to Guideline 2006/66/EC.
CONDTROL reserves the right to make changes in design and delivery package without prior notice. [EAC Mark]
Condtrol - SHOP