dormakaba USA | For every place that matters
Installation Guide for dormakaba models including: ESA500 Fixed Sidelite all Glass Automatic Sliding Door with ESA II Controller, ESA500, Fixed Sidelite all Glass Automatic Sliding Door with ESA II Controller
Objets BIM - Téléchargement gratuit ! Automatic Sliding Door, All Glass ESA500 Showcase | BIMobject Instructions d'installation
ESA 500 All Glass Partial Breakout Automatic Sliding Door
Jun 14, 2022 — Screwdrivers. Small Straight (FlatBlade) - for Terminal Block wiring. #2 Phillips (Crosspoint) - for various #8, #10, and #14 screws. Wrenches / Sockets.
File Info : application/pdf, 14 Pages, 1,005.55KB
DocumentDocumentESA500
Fixed sidelite/all glass automatic sliding door with ESA II controller
Installation Manual
DL2844-050 05-2022
| EN |
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door
Installation Manual
·Tools Required: Screwdrivers Small Straight (FlatBlade) - for Terminal Block wiring · #2 Phillips (Crosspoint) - for various #8, #10, and #14 screws Wrenches / Sockets 7/16" - for #1/4-20 Hex Head bolts attaching header to jambs 1/2" (13mm) - for #5/16 Hex Head bolts attaching end stops and operator parts · 15/16" wrench - for carrier and anti-rise roller adjustment Allen Wrenches 3mm - for "SX" & "SO" roller catch adjustment 1/8" - for "SO" arm stop & "SX" bottom pivot 5/32" - for "SO" top pivot 5mm (3/16") - for "SO" arm pivot screw 7/32" - for "SX" breakout adjustment · 5/16" - for carrier and anti-rise roller adjustment Electric Drill with the following drill bits 9/64" (or#28) - for installing sensors & "SO" bottom roller stop 5/32" (or#22) - for installing #10 sheet metal screws into adjacent storefront 13/64" (or#7) - for installing #14 sheet metal screws into adjacent storefront 1/4" - for clearance holes in jambs · 82 degree Countersink Impact Drill with the following masonry bits 1/4" - for #10 screw anchors ······· 5/16" - for #14 screw anchors Level - suggested 4' minimum
Step Ladder - 4' or 6'
Tape Measure
Caulking and Application Gun
Electrical Wire Strippers / Cutters - for sensor wiring
Grease [to hold "SX" bottom guide block on shaft]
BEA Universal Remote Control - for adjusting sensors
·Suggested Fasteners Required - (Not supplied) Jamb Attachment Screws #14 X 2-1/2" PHSMS (Pocket Jambs) #14 X 3" FHSMS (Tube Jambs) · Optional Anchors for masonry Threshold Attachment Screws #10 X 1-1/2" FHSMS · Optional Anchors for masonry Header Attachment Screws #14 X 1-1/2" HHSMS #14 Flat Washer
· Construction Shims - for squaring door frame in opening
2
ESA500
DL2844-050
05-2022
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
2 3
1 5
4
4
2 3
6
1 Components - Overview
1 Header Unit 2 Jamb
4 Fixed Sidelight ("O" Panel) 5 SliSSSing Panel ("SX" Panel)
7 Program Switch 3 Motion Detector
ESA500
DL2844-050
05-2022
3
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
2
Header to Jamb Assembly
Fasten the header unit to the jambs using (5) 1/4-20 x 1" hex bolts per side. (7/16" socket/wrench required.)
4
ESA500
DL2844-050
05-2022
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
2.
2.
2.
1. 3.
3
Assembly
1 Place the header & jamb assembly into the rough opening. 2 Level all sides and shim as required.
The mounting of the operator to the rough opening must meet applicable building codes and standards.
3 Fasten assembly into rough opening, after verifying unit is level and plumb in all directions.
ESA500
DL2844-050
05-2022
5
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
4
Sidelite Mounting
Feed the safety beam cables through the pre-drilled holes in the header and lay in the radiused trough as shown above. Stand the sidelite in place and plumb all sides. If necessary use shims below the track to level any unevenness in the flooring. Secure the sidelite in position using clamps or similar means.
6
ESA500
DL2844-050
05-2022
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
2 1
#8 Flathead Sheet Metal
4
3
5
Securing the Sidelite
1 Verify that the sidelite is plumb in all directions and properly seated against the jamb. 2 Pre-drill holes through header and sidelite on top with 1/8" drill. 3 Use screws to attach the sidelite on top, to the header. 4 Secure the bottom of the sidelite by drilling through the holes in the floor rail, shim as necessary, then fasten into place.
Verify that the sidelite is plumb in all directions and make any necessary adjustments.
ESA500
DL2844-050
05-2022
7
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
CW
3/16"+/-
15/16" Wrench 5/16" Allen
AW
AW
CW
CW
AW
6
Vertical Alignment for SX panel
Using the eccentric carrier wheel (CW), and the anti-riser wheel (AW), level the sliding panel. Tighten hex nuts to secure the adjustment.
Adjustment of the anti-riser roller: The anti-riser roller should not contact the top track anywhere along the slide path of the door.
8
ESA500
DL2844-050
05-2022
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
1/4-20 x 5/8" 1/4 flat washer
7
SX Panel Centerline Adjustment
1. With the lower belt bracket securely fastened and the upper belt bracket in its loose position, the SX panels can be properly adjusted to their center position.
2. After panels are centered, fasten upper belt bracket to carrier. (7/16" socket or wrench required.)
ESA500
DL2844-050
05-2022
9
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
3
ab
c
d
Note: It may be necessary to temporarily move
deadstop bracket out of the way to access
adjustment screw "d".
1/8" Allen wrench required.
8 Adjustment of the Breakout-Unit
1. Loosen the set screws (a, b & c) to prevent interference while adjusting door. (7/32" Allen wrench required.) 2. Use the adjustment screw (d) to lift (CW), or lower (CCW), the leading edge of door. 3. Continue adjustment until the re-latch profiles are properly aligned. 4. Tighten all set screws (a, b & c) until tight and secure. Recheck the latched position alignment and readjust as necessary.
10
ESA500
DL2844-050
05-2022
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
CW lowers the brass roller increasing tension.
CCW raises the brass roller decreasing the
tension.
9 Adjustment of the Roller Catch
Align the roller catches as illustrated using the adjustment screws. (3mm Allen wrench tool required.) Pay close attention to the disengagement or breakout force. Do not exceed ANSI A156.10 Standards.
ESA500
DL2844-050
05-2022
11
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
Door opening
3/4 inch
10
Adjustment of the End Stops
End stops are installed at the factory. Adjustments should be made by loosening the bolt and sliding the stop to the appropriate position. Be sure adjustments are made symmetrically to the door opening, while providing proper finger safety per ANSI A156.10 standards. (½" socket or wrench required.)
12
ESA500
DL2844-050
05-2022
ESA500 Fixed Sidelite/All Glass Automatic Sliding Door Installation Manual
This page left intentionally blank.
ESA500
DL2844-050
05-2022
13
www.dormakaba.us
dormakaba USA, Inc. 1 Dorma Drive, Drawer AC Reamstown, PA 17567 USA T: 717-336-3881 F: 717-336-2106