Installation Guide for Stinger models including: MT-700.1, MT-1000.1, MT-1500.1, MT-2000.1, MT-700.1 MT Series Monoblock Amplifiers, MT-700.1, MT Series Monoblock Amplifiers, Monoblock Amplifiers, Amplifiers
700 Watt RMS Monoblock Car Audio Amplifier | MT-700.1 – Stinger Off-Road – Jeep Audio And Electronics
® MT SERIES MONOBLOCK AMPLIFIERS MT-700.1 MT-1000.1 MT-1500.1 MT-2000.1 Installation Guide Specifications Power Connections An external fuse must be added to the Positive (+) wire. Refer to the Specs for the correct size fuse. Remote Turn-On from head unit or line output converter (LOC) Signal Connections Adjust bass level remotely from the driver's seat. RCA Line Out from head unit or line output converter (LOC) Amplifier Controls 2 34 567 89 1 1. Protect LED [PRT] Red when amplifier is powering up or in Protection Mode. See Troubleshooting for more information. Power LED [PWR] Blue when amplifier is ON. 2. REMOTE Connect the SA1RBC Remote Bass Control knob here. 3. INPUT Connect to line level output RCAs from head unit or line output converter (LOC). 4. BRIDGE Used to connect two amplifiers together. See page 8. 5. GAIN Used to adjust the input sensitivity to match the input level signal. 6. Low Pass Filter [LPF] A low pass crossover for the subwoofer output. Variable from 40Hz to 180Hz.Generally set around 80Hz. 7. SUBSONIC A high pass crossover for the subwoofer output. Variable from OFF to 50Hz. Generally set between 30-35Hz. 8. Boost Frequency [FREQ] Selects the frequency to boost when adding BOOST. Variable from 30Hz to 80Hz. 9. BOOST Boosts the selected frequency [FREQ] from 0dB to 12dB. MT-2000.1 Specs RMS Power Ratings listed at less than 1% THD @ 14.4v 1 2 4 Bridged RMS Rating / 2 Minimum Signal to Noise (@ CEA Standard) 2000W X 1 1500W X 1 800W X 1 3800W x 1 -93dB Input Sensitivity 0.2-6v Gain Crossover Control, Linkwitz-Riley: 0.2v - 6v SUB 0Hz - 50Hz (Subsonic) LP 40Hz - 180Hz @ 12dB/Oct Bass-Boost Frequency Range Bass-Boost Q 30-80 Hz 0-12dB Frequency Response(+- 1dB) 10Hz - 180Hz Efficiency (Average) Topology Class 80% Class D Remote Bass Control Operating Voltage Yep (Included) 9V to 16V Power Terminal 0/1 Gauge Speaker Terminal Recommended External Fusing 8 Gauge 200A MT-1500.1 Specs RMS Power Ratings listed at less than 1% THD @ 14.4v 1 2 4 Bridged RMS Rating / 2 Minimum Signal to Noise (@ CEA Standard) 1500W X 1 1000W X 1 550W X 1 2800W x 1 -93dB Input Sensitivity 0.2-6v Gain Crossover Control, Linkwitz-Riley: 0.2v - 6v SUB 0Hz - 50Hz (Subsonic) LP 40Hz - 180Hz @ 12dB/Oct Bass-Boost Frequency Range Bass-Boost Q 30-80 Hz 0-12dB Frequency Response(+- 1dB) 10Hz - 180Hz Efficiency (Average) Topology Class 82% Class D Remote Bass Control Operating Voltage Yep (Included) 9V to 16V Power Terminal 4 Gauge Speaker Terminal Recommended External Fusing 8 Gauge 150A MT-1000.1 Specs RMS Power Ratings listed at less than 1% THD @ 14.4v 1 2 4 Bridged RMS Rating / 2 Minimum Signal to Noise (@ CEA Standard) 1000W X 1 700W X 1 400W X 1 1800W x 1 -93dB Input Sensitivity 0.2-6v Gain 0.2v - 6v Crossover Control, Linkwitz-Riley: SUB 0Hz - 50Hz (Subsonic) LP 40Hz - 180Hz @ 12dB/Oct Bass-Boost Frequency Range Bass-Boost Q 30-80 Hz 0-12dB Frequency Response(+- 1dB) 10Hz - 180Hz Efficiency (Average) 82% Topology Class Class D Remote Bass Control Operating Voltage Yep (Included) 9V to 16V Power Terminal 4 Gauge Speaker Terminal 8 Gauge Recommended External Fusing 100A MT-700.1 Specs RMS Power Ratings listed at less than 1% THD @ 14.4v 1 2 4 Bridged RMS Rating / 2 Minimum Signal to Noise (@ CEA Standard) 700W X 1 500W X 1 300W X 1 1200W x 1 -93dB Input Sensitivity 0.2-6v Gain 0.2v - 6v Crossover Control, Linkwitz-Riley: SUB 0Hz - 50Hz (Subsonic) LP 40Hz - 180Hz @ 12dB/Oct Bass-Boost Frequency Range Bass-Boost Q 30-80 Hz 0-12dB Frequency Response(+- 1dB) 10Hz - 180Hz Efficiency (Average) 85% Topology Class Class D Remote Bass Control Operating Voltage Yep (Included) 9V to 16V Power Terminal 4 Gauge Speaker Terminal 8 Gauge Recommended External Fusing 80A Bridging (Connecting) Two Amplifiers Connect Bridge Out on the Primary amplifier to Bridge In on the Secondary amplifier. Connect the Negative speaker output on the Primary amplifier to the Negative speaker output on the Secondary amplifier. Connect the Positive speaker output of the Primary amplifier to the positive speaker terminal. Connect the Positive speaker out put of the Secondary amplifier to the negative speaker terminal. 2 ohm minimum! All adjustments are made on the Primary amplifier. LIMITED WARRANTY Stinger warrants this product to be free of defects in materials and workmanship for a period of one (1) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Stinger dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Stinger will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty. INTERNATIONAL WARRANTIES: Products purchased outside the United States of America are covered only by that country's Authorized Stinger reseller and not by Stinger. Consumers needing service or warranty information for these products must contact that country's reseller for information. STOP! Please DO NOT return to seller For help with installation, replacement parts, warranty or returns, please contact us directly at 727-732-3114 or support@stingerelectronics.com Stinger is a Power Brand of AAMP Global ® 15500 Lightwave, Clearwater, Florida 33760 © 2022 AAMP Global MCAMP-IG REV 102622Adobe PDF Library 16.0.7 Adobe InDesign 17.3 (Windows)