BAOFENG UV-5G PRO GMRS Radio

PREFACE

Thank you for purchasing the BAOFENG UV-5G PRO Two Way Radio. It is a multitask GMRS transceiver. Combining the latest technology in radio communication along with a sturdy mechanical frame, the UV-5G PRO is an ideal and effective solution for professionals who need to stay in touch with their working team (in construction sites, buildings, shows, trade fairs, or hotels) or for leisure users who just want to keep up with friends and family.

IMPORTANT NOTICE

To help users ward off bodily injury or property loss that may arise from improper operation, please read all the information carefully before using BAOFENG products. This manual contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation.

Safety Information for GMRS Radios

The wireless handheld portable transceiver contains a low power transmitter. When the talk button is pushed, it sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. In August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless devices.

FCC Part 15.21 Warning Statement

THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY TO OPERATE THE EQUIPMENT.

RF Exposure Information

WARNING! Read this information before using the radio.

In August 1996, the Federal Communications Commission (FCC) of the United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to radio frequency electromagnetic energy emitted by FCC regulated transmitters. These guidelines are consistent with safety standards previously set by both U.S. and international standards bodies. The design of the radio complies with FCC guidelines and international standards.

Never allow children to operate the radio without adult supervision and knowledge of the following guidelines.

WARNING! It is up to the user to properly operate this radio transmitter to ensure safe operation. Please adhere to the following:

• Use only the supplied or an approved antenna. Unauthorized antennas, modifications, or attachments could impair call quality, damage the radio, or result in violation of FCC regulations.
• Do not use the radio with a damaged antenna.
• If a damaged antenna comes into contact with the skin, a minor burn may result. Contact a local dealer for a replacement antenna.

Hand-held Operation (Held-to-Face)

This device was evaluated for typical hand-held (held-to-face) operations with a 1 inch spacing from the front of the radio. For hand-held operation, the radio should be held 1 inch from the user's face to comply with FCC RF exposure requirements.

For more information about RF exposure, please visit the FCC web site at www.fcc.gov.

Body-worn Operation

This device was evaluated for body-worn operations with the supplied belt-clip accessory. All necessary accessories are included in the package; any additional or optional accessories are not required for compliance with the guidelines. Third-party accessories (unless approved by the manufacturer) should be avoided as these might not comply with FCC RF exposure guidelines.

For more information about RF exposure, please visit the FCC web site at www.fcc.gov.

GMRS Communication

The GMRS (General Mobile Radio Service) feature is a land-mobile service available for short-distance, two-way communications in the USA. A valid FCC license is required to communicate on these channels. The GMRS/FRS frequencies used by this radio are set aside for communicating with others while hiking, biking, and working; keeping track of family and friends at crowded public events; checking with travel companions in another car; talking with neighbors; and arranging meeting spots while shopping at the mall. Licensed users will be issued a call sign by the FCC, which should be used for station identification when operating this radio. GMRS users should also cooperate by engaging in permissible transmissions only, avoiding channel interference with other GMRS users, and being prudent with the length of their transmission time.

FCC License Required

This two-way radio operates on GMRS (General Mobile Radio Service) frequencies which require an FCC (Federal Communications Commission) license. A user must be licensed prior to transmitting on the GMRS band with this radio. Serious penalties could result for unlicensed use of GMRS channels, in violation of FCC rules. Operation of this radio is subject to additional rules specified in 47 C.F.R. Part 95. For licensing information and application forms, please call the FCC Hotline at 800-418-FORM. Request form #159 and form #605. Questions regarding the license application should be directed to the FCC at 888-CALL-FCC. Additional information is available on the FCC's website at www.fcc.gov.

NOTE: Even if this radio operates on FRS (Family Radio Service) channels at low power (0.5 watt), an FCC license is still required. Because this radio operates in the 0.5 to 5 watt GMRS power range, all GMRS rules apply and will require a GMRS license even for FRS communication. Normal FRS-only radios operate at a maximum power of 0.5 watt (500 milliwatt) and have an integral (non-detachable) antenna.

FCC Warnings

Replacement or substitution of transistors, regular diodes, or other parts of a unique nature, with parts other than those recommended by Pofung, may cause a violation of the technical regulations of part 95 of the FCC rules, or violation of type acceptance requirements of part 2 of the rules.

Precautions for Portable Terminals

Operating Prohibitions

To protect against property loss, bodily injury, or even death, observe the following safety instructions:

1. Do not operate the product in a location containing fuels, chemicals, explosive atmospheres, and other flammable or explosive materials. In such locations, only an approved Ex-protection model is allowed for use, and any attempt to assemble or disassemble it is strictly prohibited.
2. Do not operate the product near or in any blasting area.
3. Do not operate the product near any medical or electronic equipment that is vulnerable to RF signals.
4. Do not hold the product while driving.
5. Do not operate the product in any area where use of wireless communication equipment is completely prohibited.

Important Tips

To make better use of the product, observe the following instructions:

1. Do not use any unauthorized or damaged accessory.
2. Keep the product at least 2.5 centimeters away from the body during transmission.
3. Do not keep the product receiving at high volume for a long time.
4. For vehicles with an airbag, do not place the product in the area over the airbag or in the airbag deployment area.
5. Keep the product and its accessories out of reach of children and pets.
6. Operate the product within the specified temperature range.
7. Continuous transmission for a long time may lead to heat accumulation within the product. In this case, keep it at a proper location for cooling.
8. Handle the product with care.
9. Do not disassemble, modify, or repair the product and its accessories without authorization.

Precautions for Batteries

Charging Prohibitions

To protect against property loss, bodily injury, or even death, observe the following safety instructions:

1. Do not charge or replace the battery in a location containing fuels, chemicals, explosive atmospheres, and other flammable or explosive materials.
2. Do not charge a wet battery. Dry it with a soft and clean cloth prior to charging.
3. Do not charge a battery suffering deformation, leakage, or overheating.
4. Do not charge a battery with an unauthorized charger.
5. Do not charge a battery in a location where strong radiation is present.
6. Overcharging is prohibited as it may shorten the battery life.

Maintenance Instructions

To help the battery work normally or prolong its life, observe the following instructions:

1. Accumulated dust on the charging connector may affect normal charging. Use a clean and dry cloth to wipe it regularly.
2. It is recommended to charge the battery under 5°C~40°C. Violation of this limit may cause battery life reduction or even battery leakage.
3. To charge a battery attached to the product, turn it off to ensure a full charge.
4. Do not remove the battery or unplug the power cord during charging to ensure a smooth charging process.
5. Do not dispose of the battery in fire.
6. Do not expose the battery to direct sunlight for a long time nor place it close to other heating sources.
7. Do not squeeze and penetrate the battery, nor remove its housing.

Transportation Instructions

1. Damaged batteries must not be transported.
2. To avoid short circuits, separate the battery from metal parts or from each other if two or more batteries are transported in one packaging.
3. The radio must be switched off and secured against switch-on if the battery is attached.

The content of the shipment must be declared in the shipping documents and by a Battery Shipping Label on the packaging. Contact your hauler for local regulations and further information.

Chapter1. Getting Started

1.2 Content of the packaging

• 1 Radio
• 1 Li-Ion battery pack
• 1 Fast desktop charger
• 1 Wall adaptor
• 1 Antenna
• 1 Belt clip

If any item is missing, verify with your dealer.

1.3 Main features

• 22 Modifiable GMRS Channels (RX & TX)
• 8 Modifiable GMRS Repeater Channels (RX & TX)
• Scanning receiver frequency range: FM 76-108 MHz; AM 108-136MHz; VHF 136-260MHz, UHF 400-520MHz
• One touch search frequency, easy pairing and grouping (copying channel configuration parameters)
• Frequency step, selectable between 2.5K | 5.0K | 6.25K | 10.0K | 12.5K | 20.0K | 25.0K | 50.0K
• Frequency hopping and scramble functions to keep call privacy confidential
• Channel scan, frequency scan, and three scan and recovery methods: TO, CO, and SE
• Up to 128 memory channels.
• DTMF encoder and DTMF manual dial
• VOX (voice activated transmit).
• Alarm function.
• Programmable repeater offset.
• Transmission time-out timer.
• LED flashlight.
• End of transmission tone, also known as "Roger Beep"
• Broadcast FM radio receiver 76-108 MHz
• High Capacity Lithium-Ion battery.
• Display illumination programmable via keypad.
• Battery save function.
• Busy channel lock out.
• Ten (10) levels of Squelch adjustment.
• Two (2) pins for Kenwood accessory port
• Support NOAA weather reception function in the United States and Canada

Chapter2. Battery Information

2.1 Charging the Battery Pack

The Li-ion battery pack is not charged at the factory; please charge it before use. Charging the battery pack for the first time after purchase or extended storage (more than 2 months) may not bring the battery pack to its normal maximum operating capacity. Best operation will require fully charging/discharging the battery two or three times before the operating capacity reaches its best performance. The battery pack life may be depleted when its operating time decreases even though it has been fully and correctly charged. If this is the case, replace the battery pack.

2.2 Charger Supplied

Please use the specified charger provided by BAOFENG. Other models may cause explosion and personal injury. After installing the battery pack, and if the radio displays low battery with a voice prompt, please charge the battery.

2.3 Use Caution with the Li-ion Battery

1. Do not short the battery terminals or throw the battery into a fire. Never attempt to remove the casing from the battery pack, as BAOFENG cannot be held responsible for any accident caused by modifying the battery.
2. The ambient temperature should be between 5°C-40°C (40°F - 105°F) while charging the battery. Charging outside this range may not fully charge the battery.
3. Turn off the radio before inserting it into the charger. It may otherwise interfere with correct charging.
4. To avoid interfering with the charging cycle, do not cut off the power or remove the battery during charging until the green light is on.
5. Do not recharge the battery pack if it is fully charged. This may shorten the life of the battery pack or damage the battery pack.
6. Do not charge the battery or the radio if it is damp. Dry it before charging to avoid damage.

WARNING!

When keys, ornamental chain, or other electric metals contact the battery terminal, the battery may become damaged or injure a human. If the battery terminals are short-circuited, it will generate a lot of heat. Take care when carrying and using the battery. Remember to put the battery or radio into an insulated container. Do not put it into a metal container.

2.4 How to Charge

1. Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the charger. The indicator light blinks orange and is then ready to charge a battery.
2. Plug the battery or the radio into the charger. Make sure the battery terminals are in good contact with charging terminals. The indicator light turns red, indicating charging begins.
3. It takes approximately 2-5 hours to fully charge the battery. When the lamp lights green, charging is completed. Remove the battery or the radio unit with its battery from the socket.

When charging a radio (with battery), the indicating lamp will not turn green to show the fully charged status if the radio is powered on. Only when the radio is switched off will the lamp indicate normal operation. The radio consumes energy when it is powered on, and the charger cannot detect the correct battery voltage when the battery has been fully charged. So the charger will charge the battery in constant voltage mode and fail to indicate correctly when the battery has been fully charged.

2.5 LED Indicator

NOTE: Trouble means battery too warm, battery short-circuited.

Chapter3. Installation of Accessories

Before the radio is ready for use, attach the antenna and battery pack, and charge the battery.

3.1 Installing/ Removing the Antenna

1. Installing the Antenna: Screw the antenna into the connector on the top of the transceiver by holding the antenna at its base and turning it clockwise until secure.
2. Removing the Antenna: Turn the antenna counter-clockwise to remove it.

3.2 Installing the belt clip

1. At the back of the radio, there are two parallel screws mounted above the battery. Remove these and thread them through the holes on the belt clip as you screw them back into the radio body.
2. Removing the Belt Clip: Unscrew counter-clockwise to remove the belt clip.

3.3 Installing the battery pack

Before attaching or removing the battery, ensure the radio is turned off by turning the power/volume knob all the way counter-clockwise.

1. Make sure the battery is aligned in parallel with the radio body with the lower edge of the battery about 1-2cm below the edge of the radio.
2. Once aligned with the guide-rails, slide the battery upward until a click is heard as the battery locks in place.

Remove the battery pack

To remove the battery, press the battery release above the battery pack as you slide the battery downward.

3.4 Installing the Additional Speaker/Microphone (Optional)

Pry open the rubber MIC-Headset jack cover and then insert the Speaker / Microphone plug into the double jack.

Chapter4. Radio Overview

4.1 Buttons and controls of the radio

The radio features various buttons and controls for operation:

1. Antenna
2. LED flashlight
3. Power / Volume knob
4. Two-line LCD
5. Call key
6. Monitor key
7. PTT - Push to talk
8. VFO/MR mode key
9. Status LED
10. Lanyard loop
11. Accessory jack
12. A / B select key
13. BAND key
14. Keypad
15. Speaker and microphone
16. Battery pack
17. Battery contacts
18. Battery release latch

4.2 Main controls and parts of the radio: LCD Display

The LCD display provides various status indications:

Note: Even though it is a seven character by two-line display, channel memories are only configurable to six character names.

Battery Level Indicator

When the battery level indicator shows an empty battery symbol (?), the battery is depleted. At this point, the radio will start beeping periodically, flash the backlight of the display, and if voice prompts are enabled, a "Low Voltage" announcement will be heard, indicating that the battery needs to be changed or the radio needs to be put in the charger.

4.3 Status Indications

The status LED has a simple and traditional design. When a signal is received, it turns green; when transmitting, it turns red; and it is off in standby.

4.4 Main keypad controls

• [CALL] key: Press briefly to turn on the FM radio. Press again to turn it off. Press and hold to activate the alarm function. Press again to turn off this feature.
• [MON] key: Press briefly to light up the flashlight. Press again for strobe mode. Press a third time to turn off the flashlight. To activate the Monitor function, press and hold the button.
• [VFO/MR] key: Switches between Frequency (VFO) Mode and Memory (MR) mode. Memory mode is sometimes referred to as Channel mode. To save frequencies to channel memory, the radio must be in Frequency (VFO) mode.
• [A/B] key: Switches between A (upper) and B (lower) displays. The frequency or channel on the selected display becomes the active listening and transmit frequency or channel. To save frequencies to channel memory, the radio must be on the A display.
• [MENU] key: Used for activating the MENU, choosing each MENU selection, and confirming the parameter.
• [▲] key: Press for more than 2 seconds to move the channel and frequency rapidly upwards; in SCAN mode, press to move scanning upwards.
• [▼] key: Keep pressed for more than 2 seconds to move the channel and frequency rapidly downwards; in SCAN mode, press to move scanning downwards.
• [EXIT] key: Push this button to exit functions and settings.
• [BAND] key: Press to switch between VHF or UHF bands. Press and hold the [BAND] key to activate the one-touch search function. When listening to broadcast FM, the [BAND] key switches between 65-75 MHz and 76-108 MHz bands.

Chapter5. Basic Operations

5.1 Power on the radio

To turn the unit on, simply rotate the Volume/Power knob clockwise until a "click" is heard. If the radio powers on correctly, an audible double beep should be heard after about one second, and the display will show a message or flash the LCD depending on settings for about one second. Then it will display a frequency or channel. If the Voice prompt is enabled, the voice will announce "frequency mode" or "channel mode". Turn the Volume/Power knob counter-clockwise all the way until a "click" is heard to turn the unit off.

5.2 Adjusting the volume

To turn up the volume, turn the Volume/Power knob clockwise. To turn the volume down, turn the Volume/Power knob counter-clockwise. Be careful not to turn it too far, as it may inadvertently turn the radio off.

5.3 Making a call

NOTE: Press the [A/B] key to switch the main channel to the other channel if two channels are shown on the display. Press the [VFO/MR] key to switch between VFO and channel display.

• Channel mode call: After selecting a channel, hold down the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. When a call is initiated, the red LED is on.
• Frequency mode call: Press the [VFO/MR] key to switch to the frequency mode, enter the allowed frequency range, then press the [PTT] key to initiate a call to the current channel. Speak into the microphone with normal tone. When a call is initiated, the red LED is on.
• Receive a call: When the [PTT] key is released, a call can be answered without any action. When receiving a call, the green LED is on.

NOTE: To ensure the best reception volume, keep the distance between the microphone and the mouth at the time of transmission from 2.5 cm to 5 cm.

5.4 Channel selection

There are two modes of operation: Frequency (VFO) mode, and Channel or Memory (MR) mode. For everyday use, Channel (MR) mode is generally more practical than Frequency (VFO) mode. However, Frequency (VFO) mode is very handy for experimentation in the field and is also used for programming channels into memory. In Channel (MR) mode, channels can be navigated up and down using the up arrow (▲) and down arrow (▼) keys. The mode used ultimately depends on the user's specific use case.

5.5 Frequency (VFO) mode

In Frequency (VFO) mode, the band can be navigated up and down using the up arrow (▲) and down arrow (▼) keys. Each press will increment or decrement the frequency according to the frequency step set for the transceiver. Frequencies can also be input directly on the numeric keypad with kilohertz accuracy. The following example assumes the use of a 12.5 kHz frequency step.

Example. Entering the frequency 462.6125 MHz on display A

1. Use the [VFO/MR] key to switch to Frequency (VFO) mode.
2. Press [A/B] until the up arrow (▲) icon appears next to the upper display.
3. Enter [4][6][2][6][1][2][5] on the numeric keypad.

WARNING!

Just because a channel can be programmed does not mean automatic authorization to use that frequency. Users may be tempted to use PMR446, FRS, GMRS, and MURS (in USA) frequencies. Note, however, that restrictions on these bands make this transceiver illegal for use. Contact the local regulatory body for further information on applicable laws, rules, and regulations.

5.6 Channel (MR) mode

The use of Channel (MR) mode depends on having programmed channels. Once channels are programmed and ready, the up arrow (▲) and down arrow (▼) keys can be used to navigate between channels.

Note: If channels are programmed with Transmit power set to Low, the [#TO] key can be used to momentarily switch to mid or high power if there is trouble getting through.

Chapter6. Advanced Features

6.1 Frequency scanning

This function allows frequency scanning.

1. In frequency mode, press the [*/SCAN] key for more than 2 seconds. The radio will start scanning the frequency according to the set frequency step.
2. The scanning direction can be changed with the up arrow (▲) and down arrow (▼) keys.
3. Press any key to stop the scanning.

Note: For Scan mode, see Menu No.18.

6.2 Channel scanning

This function allows channel scanning.

1. In channels mode, press the [*/SCAN] key for more than 2 seconds. The radio will start scanning according to the channel set.
2. The scanning direction can be changed with the up arrow (▲) and down arrow (▼) keys.
3. Press any key to stop scanning.

Note: For Scan mode, see Menu No.18.

6.3 Tone Scanning

Scanning for CTCSS and DCS Tones/Codes

Scanning for a CTCSS tone or DCS code can be done while Frequency Mode (VFO) or Channel Mode (MR) is selected. Only when VFO mode is selected can the detected tone/code be saved to menu 11/10. CTCSS tone and DCS code scanning mode can be accessed with or without a signal being present. The scanning process itself only occurs while a signal is being received. Not all repeaters requiring a CTCSS tone or DCS code for access will transmit one back. In that case, the transmitter of a station that can access the repeater would need to be scanned. In other words: this would be done by listening to stations on the repeater's input frequency.

Scanning for CTCSS Tone

1. Press [MENU] [1] [1] to access Menu 11: R-CTCS.
2. Press the [MENU] key to select. Ensure a tone is activated (not off).
3. Press the [*SCAN] to begin CTCSS scanning.

A flashing "CT" will appear in the left status display to indicate the radio is in CTCSS scanning mode. In this mode, whenever the radio is receiving an RF signal on the selected MR channel or VFO frequency, the lower display will cycle through the CTCSS tones as they are being tested. Once the frequency of the received CTCSS tone is determined, the "CT" indicator will stop flashing. Press the [MENU] key to save the scanned tone into memory (VFO Mode Only), then press the [EXIT] key to exit the menu. Do not forget to set VFO menu 11 back to OFF when the CTCSS tone is no longer required.

Scanning for a DCS tone

1. Press the [MENU] [1] [0] to access Menu 10: R-DCS.
2. Press the [MENU] key to select. Ensure a tone is activated (not off).
3. Press the [*SCAN] to begin DCS scanning.

A flashing "DCS" will appear in the left status display to indicate the radio is in DCS scanning mode. In this mode, whenever the radio is receiving an RF signal on the selected MR channel or VFO frequency, the lower display will cycle through the DCS codes as they are being tested. Once the bits of the received DCS code are determined, the "DCS" indicator will stop flashing. Press the [MENU] key to save the scanned tone into memory (VFO Mode Only), then press the [EXIT] key to exit the menu. Do not forget to set VFO menu 10 back to OFF when the DCS tone is no longer required.

6.4 Dual Watch

The BAOFENG UV-5G PRO features Dual Watch functionality (single receiver) with the ability to lock the transmit frequency to one of the two channels it monitors.

Enabling or disabling Dual Watch mode

1. Press the [MENU] [7] to access MENU 7: TDR.
2. Press the [MENU] key to select.
3. Use the up arrow (▲) and down arrow (▼) keys to enable or disable.
4. Press the [MENU] key to confirm.
5. Press the [EXIT] key to exit the menu.

Due to the way the BAOFENG UV-5G PRO is constructed, whenever one of the A or B Frequencies (VFO/MR) goes active, it will default to transmit on that channel. This behavior can be inconvenient, especially if monitoring a frequency that should not be transmitted on. There is a menu option available to lock the transmitter to one of the A or B channels.

Locking the Dual Watch transmit channel

1. Press the [MENU] [3][4] to access MENU 34: TDR-AB.
2. Press the [MENU] key to select.
3. Use the up arrow (▲) and down arrow (▼) keys to select A (upper) or B (lower) display.
4. Press the [MENU] key to confirm.
5. Press the [EXIT] key to exit the menu.

To momentarily override the lock without setting the menu option to OFF, press the [A/B] key an instant before pressing the PTT. Another option is to disable menu [7] (TDR) to override the lock. Then re-enable TDR when the lock is to be resumed.

6.5 Cursor Conversion (A/B)

Directly press the [A/B] key to move the cursor up and down. Then, parameters indicated by the cursor can be modified or confirmed.

Important1: The UV-5G PRO has a dual-frequency display function. In frequency mode, two different receiving and transmitting frequencies will be displayed; while in channel mode, two different channels will be displayed.

Important2: In frequency or channel mode, press the [A/B] key to shift between the main channel A and the sub-channel B. The up arrow (▲) is displayed next to the channel indicating which channel (main channel A or sub channel B) is being operated on.

6.6 High/low power fast selection

In channel mode, press the [#TO] key to shift between high and low power.

6.7 Keypad lock

This function locks the keypad to prevent accidental pressure of the controls. To unlock the keypad, press [#TO] for more than 2 seconds.

6.8 FM Radio (FM)

The frequency range to listen to the radio is 65-108MHz. When listening to broadcast FM, press the [A / B] key to switch between 65-75 MHz and 76-108 MHz bands.

1. In frequency or channel mode, press [CALL] to turn on the radio.
2. Select the desired radio frequency with the up arrow (▲) or down arrow (▼) keys or input the frequency. Alternatively, press [*SCAN] to automatically search for a radio station.
3. Press [CALL] to exit FM radio.

Note: While listening to the radio, the frequency or channel of an A / B receiving signal will automatically switch to the frequency or channel mode for normal transmitting and receiving. When the signal disappears, the radio will automatically switch again to FM radio mode.

6.9 Flashlight

This function is useful for night illumination. To turn it on, press MON; press again for strobe mode; press again to turn it off.

6.10 1000Hz, 1450Hz, 1750Hz Tone-burst

To send out a tone-burst, simultaneously press a key while holding down the PTT. No further configuration is required for this feature. The following configurations will transmit accordingly:

• [PTT] + [CALL] = Transmits 1000Hz Tone Burst
• [PTT] + [VFO/MR] = Transmits 1450Hz Tone Burst
• [PTT] + [A/B] = Transmits 1750Hz Tone Burst

If the keypad lock is enabled on the radio, a 1750Hz tone can still be sent without unlocking the radio.

6.11 DTMF

DTMF is an in-band signaling method using dual sinusoidal signals for any given code. Originally developed for telephony systems, it has proved a versatile tool in many other areas. In two-way radio systems, DTMF is most commonly used for automation systems and remote control. A common example would be in amateur radio repeaters where some repeaters are activated by sending out a DTMF sequence (usually a simple single-digit sequence).

The BAOFENG UV-5G PRO EU has a full implementation of DTMF, including the A, B, C, and D codes. The numerical keys, as well as the [*SCAN], and [#TO] keys, correspond to the matching DTMF codes. The A, B, C, and D codes are located in the [MENU], [▲], [▼], and [EXIT] keys respectively.

To send DTMF codes, press the key(s) corresponding to the message while holding down the PTT key. If the keypad lock is enabled on the radio, DTMF tones can still be sent without unlocking the radio.

6.12 One touch frequency Search

1. The radio will act as a receiver. Press and hold the [BAND] key, and the screen will display “SEARCH UHF”.
2. If the transmitter continues to transmit and the unit receives an effective frequency (the strongest and stable signal), the received frequency will be displayed. If there is a CTCSS or DCS, the CTCSS or DCS value is displayed; if there is no CTCSS or DCS, NONE is displayed.
3. The [MENU] key can be pressed to save the Search frequency and CTCSS or DCS to the channel.

Note: During frequency Search, press the [#TO] key on the radio to switch between UHF or VHF bands.

Chapter7. Working the MENU System

For a complete reference on available menu items and parameters, see Appendix C, Shortcut Menu operations.

Note: In channel mode, the setting of these features is not possible: CTCSS/DCS tones, wide/narrow bandwidth, PTT-ID, Busy channel lock out, channel name edit.

7.1 Basic use

Using the menu with arrow keys

1. Press the [MENU] key to enter the menu.
2. Use the up arrow (▲) and down arrow (▼) keys to navigate between menu items.
3. Once the desired menu item is found, press [MENU] again to select that menu item.
4. Use the up arrow (▲) and down arrow (▼) keys to select the desired parameter.
5. When the parameter is selected for a given menu item:
1. To confirm the selection, press [MENU] to save the setting and return to the main menu.
2. To cancel changes, press [EXIT] to reset that menu item and exit the menu entirely.
6. To exit the menu at any time, press the [EXIT] key.

7.2 Using short-cuts

As noted in Appendix C, Shortcut Menu operations, every menu item has a numerical value for direct access. Parameters also have associated numbers, detailed in Appendix C, Shortcut Menu operations.

Using the menu with short-cuts

1. Press the [MENU] key to enter the menu.
2. Use the numerical keypad to enter the number of the menu item.
3. To enter the menu item, press the [MENU] key.
4. For entering the desired parameter, two options are available:
1. Use the arrow keys as in the previous section; or
2. Use the numerical keypad to enter the numerical short-cut code.
5. And just as in the previous section:
1. To confirm the selection, press [MENU] to save the setting and return to the main menu.
2. To cancel changes, press [EXIT] to reset that menu item and exit the menu entirely.
6. To exit the menu at any time, press the [EXIT] key.
7. All further examples and procedures in this manual will use numerical menu short-cuts.

Appendix A. – Trouble shooting guide

NOTE: If the above solutions cannot fix problems, or if there are other queries, contact the dealer for more technical support.

Appendix B. - Technical Specifications

Specifications are subject to change without notice.

WARNING. Direct plug-in ac/dc power supply must be used for disconnecting the transceiver from the mains; the desktop charger must be positioned close to the unit and easily accessible.

Appendix C. - Shortcut Menu operations

Appendix D. - GMRS Frequency Chart (MHz)

* Channels 8~14 are low-power FRS license free channels.

Appendix E. - DCS Table

Appendix F. - CTCSS Table

Appendix G.- NOAA Weather Radio Frequency List (US, CAN)

Disclaimer

The Company endeavors to achieve the accuracy and completeness of this manual, but no warranty of accuracy or reliability is given. All specifications and designs are subject to change without notice due to continuous technological development. No part of this manual may be copied, modified, translated, or distributed in any manner without the prior written consent of the Company. The Company does not guarantee, for any particular purpose, the accuracy, validity, timeliness, legitimacy, or completeness of third-party products and contents involved in this manual.

PO FUNG ELECTRONIC (HK) INTERNATIONAL GROUP COMPANY LIMITED

Address: Room 1508, 15/F, Office Tower II, Grand Plaza, 625 Nathan Road, Kowloon, Hong Kong

Website: www.baofengradio.com and www.pofungshop.com

Print version: UV-5G PRO_V1.0