User Manual for Kinetec models including: MCDP5200, RD1-5200, USB Type C DP Alt to HDMI and USB Type A Converter, MCDP5200 USB Type C DP Alt to HDMI and USB Type A Converter, RD1 Evaluation Kit, MCDP5200 RD1 Evaluation Kit
MCDP5200 / RD1-5200 - USB Type-C DP Alt to HDMI & USB Type-A
RD1-5200 | MCDP5200 Reference Design
File Info : application/pdf, 15 Pages, 1.37MB
DocumentDocumentReference Design EVAL Kit MCDP5200 / RD1-5200 USB Type-C DP Alt to HDMI & USB Type-A General Description The MCDP5200 is an advanced USB Type-C / DisplayPort1.4a to HDMI converter with an integrated USB type-C de-multiplexer, targeted primarily for Mobile Notebook accessory and display applications. This device functions as a DP to HDMI protocol converter with a HDCP1.x/ HDCP2.x repeater function. The MCDP5200 has a USB Type C DP Alt mode Upstream Facing Port (UFP), supporting Billboard functionality. The four high speed lanes of UFP can receive DP1.4a MST audio-video and USB3.1 Gen2 data streams simultaneously. The input lane mapping is flexible and meets the USB Type-C connector flip orientation requirements. The incoming DP and USB signals are de-multiplexed, retimed, and transmitted on the Downstream Facing Ports (DFP). The MCDP5200 consists of a USB DFP port with USB3.1 TX and RX pair and an audio-video DFP port configured as DC coupled HDMI/DVI port, each with four high-speed lanes. Ordering Information Part Number Description RD1-5200 MCDP5200 RD1 Evaluation Kit IC Package LFBGA77-169 Detailed functionality of the IC is described in the MCDP5200 datasheet. Included in the kit are the following items: Item # 1 1 Description Fully assembled printed circuit board Reference Design Evaluation kit manual Quantity 1 1 EVAL Kit Photo August 2022 Revision 03c Page 1 of 15 Kinetic Technologies Confidential Reference Design EVAL Kit MCDP5200 / RD1-5200 Contents General Description .................................................................................................................. 1 Ordering Information................................................................................................................. 1 EVAL Kit Photo.......................................................................................................................... 1 Evaluation Board Features ....................................................................................................... 3 Design Features..................................................................................................................... 3 System Overview....................................................................................................................... 5 Functional Block Diagram....................................................................................................... 5 Connection Setup................................................................................................................... 6 Diagnosis ............................................................................................................................... 6 Connector Layout ................................................................................................................... 7 MFP Pin Assignment.............................................................................................................. 8 Selected Pin Usage and Assignment ....................................................................................... 9 UFP Type-C Monitor .............................................................................................................. 9 DDC Monitor for HDMI TX .................................................................................................... 10 I2C Slave ............................................................................................................................. 11 SPI Flash & Reset ................................................................................................................ 12 Gprobe Header Pins............................................................................................................. 12 Recommended Accessories ................................................................................................... 13 AC Adapters......................................................................................................................... 13 Cables ................................................................................................................................. 13 Important Notices.................................................................................................................... 15 List of Figures Figure 1. Functional Block Diagram ............................................................................................. 5 Figure 2. Connection Setup ......................................................................................................... 6 Figure 3. Connector Layout ......................................................................................................... 7 Figure 4. MFP Pin Assignment on the Board Except for High Speed Signal ................................. 8 List of Tables Table 1.Recommended AC Adapter List .................................................................................... 13 Table 2. Recommended Cable List ............................................................................................ 13 August 2022 Revision 03c Page 2 of 15 Kinetic Technologies Confidential Reference Design EVAL Kit MCDP5200 / RD1-5200 Evaluation Board Features Design Features · DUT: MCDP5200 · Board Name: RD1-5200 · Power Supply o DC5V Input = Barrel Jack, USB Type-C (5V/3A mode) in alternative use, with over voltage protection (trip voltage 6.2~7.0V) · Interfaces o Input: USB Type-C Alt mode support Display Port: 1.62 / 2.74 / 5.4 / 8.1 Gbps, 1 /2 / 4 lane configuration USB3.2 : 5Gbps, 10Gbps x1 operation USB2: (bypassed to DFP) o Output: HDMI2.0b with HDMI Type-A Connector as DFP If UFP port is configured as 4L DP mode, then 600 MHz(max) TMDS character clock, 6Gbps(max) can be supported If UFP port is configured as USB3 + 2L DP mode, then up to 540MHz TMDS character clock can be supported. 4k2k60Hz resolution can be achieved in either reduced blanking, YUV420 or with the DSC functionality o Output: USB3.2 SSPx1 operation with USB Type-A Connector as DFP 5Gbps/10Gbps o CPU Reset: 1x Push switch o Charging Port: USB type-C Receptacle Handling voltage can be up to 20VDC as Power Delivery specification. USB PD: Through UFP USB C and DFP USB C (up to 65W) Dual Role · Components o MCDP9000 (USB PD3.0 Type-C Port Controller) o Small crystal operation: 25MHz with 2016 size (metric) o 16Mbit SPI Flash: MX25R1635FM2IH2 (default) or compatibles1. o Protection Circuit2 ESD Diodes on · RX: High Speed Line and AUX/HPD · TX1(HDMI): High Speed Line and DDC · TX0(USB3 SSP): High Speed Line · Pin header of G-Probe Interface (debug use) Over current protection · 1.5A@VBUS: USB Type-A(DFP) · 0.3A@Trip of poly-fuse (resettable fuse): HDMI +5V power supply · 1.0A@Trip of poly-fuse: for external G-Probe card o External reference resistor: 5.36k ± 1% ohm 1. Contact marketing for details on compatible memory 2. For characterization and validation testing, these can be removed if required August 2022 Revision 03c Page 3 of 15 Kinetic Technologies Confidential Reference Design EVAL Kit MCDP5200 / RD1-5200 · VRM Block (Power Distribution Network) o Lower cost components and smaller space o DCDC converter circuit compliant with noise requirement (<20mVpp) o Self-contained over-current protection circuit o Discharging load capacitors · Interfaces for debug: o 1x G-Probe Interface on USB Micro-B connector (UART signals can be bypassed to external GProbe card) o 1x JTAG(SWD) interface with J-Link 19pin o Trace pins of JTAGE interface are option o 1x HDMI DDC pins (DC coupled) on DFP o 1x Reference clock output with u-coax connector (Hirose U.FL) o 1x Reference clock input path with u-coax connector (Hirose U.FL) o 1x 6pin connector for TEST mode and VPP(6V) Power Supply o 1x Bootstrap pin header August 2022 Revision 03c Page 4 of 15 Kinetic Technologies Confidential System Overview Functional Block Diagram Reference Design EVAL Kit MCDP5200 / RD1-5200 Upstream Facing Port USB Type-C DP Altmode ESD DIODE RX VBU S FET SW1 FET SW2 4.5 ~ 24VDC VRM 4.5 ~ 24VDC VDD33 VDD18 VDDP9 VBU S_ 5V MCDP5200 TFBGA169 0.5mm pitch 7x7x1.2mm SW1 USB2.0 CC1/2 SBU USB2.0(DFP2),bypass MCDP9000 TCPC I2C,ALT# Ena bl e SBU _SW AUX DP SST HBR3 USB SSP/SS x1 TX0 ESD DIODE SW2 2C,ALT# GPIO MCDP9000 TCPC VBU S_ 5V VBUS SW USB2.0(DFP2) USB SSP/SS x1 5.0V DDC DETECT HDMI2.0 MAIN LINK USB3.2 Type A USB Type-C Charging Port For Type-C AC Adapter Type-C Port Controller Downstream Facing Port for USB To HDMI Sink HDMI 2.0 DC Couple TX1(CML) ESD DIODE DDC Mon Header 25MHz Reference Clock Mini Co-ax Mini Co-ax Clock Input Clock Output PVD D18 25MHz SPI I/F SPI FLASH 16Mb UART To USB CPU Reset SW JTAG, SWD I/F (debug IF) (power supply input) (required components/circuit) (functional interface) Figure 1. Functional Block Diagram Gporbe (USB2.0) Gprobe Interface For Debug August 2022 Revision 03c Page 5 of 15 Kinetic Technologies Confidential Reference Design EVAL Kit MCDP5200 / RD1-5200 Connection Setup 1) Connect USB Type C cable 2) Connect HDMI Cable 3) [optional] Connect USB Type C Charging port: MCDP5200 RD1 USB PD (through UFP USB C and DFP USB C Dual Role) 4) [optional]: USB3.2 Type A: Downstream Facing Port for USB supports (USB2.0, USB3.x Gen1/Gen2). 5) USB Type A-to-C cable can also be used to connect to USBC 2.0 / 3.x Gen1/Gen2 devices. Laptop/tablet/ smart phone Charging port Figure 2. Connection Setup Diagnosis If the image does not come up, follow the steps below for diagnosis. Note: The diagnosis requires the Kinetics' GProbe software3. 1) Install the GProbe diagnostic tool on a computer and set the baud rate to 115,200. 2) Connect a micro-USB cable to the CN5 connector as shown in figure2-3 (the board has a USB-UART for Gprobe Interface 3) Install the necessary driver FTDI drivers (USB to UART) and connect to the computer with the Gprobe software 4) Hit the Reset button on the board. You will see the firmware version and date of firmware in the GProbe window. This indicates the DP receiver IC is functional. If the message does not appear, contact Kinetic for further assistance. 3. Contact Kinetic Marketing for the GProbe software August 2022 Revision 03c Page 6 of 15 Kinetic Technologies Confidential Connector Layout Reference Design EVAL Kit MCDP5200 / RD1-5200 Figure 3. Connector Layout August 2022 Revision 03c Page 7 of 15 Kinetic Technologies Confidential MFP Pin Assignment Reference Design EVAL Kit MCDP5200 / RD1-5200 Figure 4. MFP Pin Assignment on the Board Except for High Speed Signal August 2022 Revision 03c Page 8 of 15 Kinetic Technologies Confidential Reference Design EVAL Kit MCDP5200 / RD1-5200 Selected Pin Usage and Assignment UFP Type-C Monitor August 2022 Revision 03c Page 9 of 15 Kinetic Technologies Confidential DDC Monitor for HDMI TX Reference Design EVAL Kit MCDP5200 / RD1-5200 August 2022 Revision 03c Page 10 of 15 Kinetic Technologies Confidential I2C Slave Reference Design EVAL Kit MCDP5200 / RD1-5200 August 2022 Revision 03c Page 11 of 15 Kinetic Technologies Confidential SPI Flash & Reset4 Reference Design EVAL Kit MCDP5200 / RD1-5200 Gprobe Header Pins 4. Flash socket might not be available as the flash will be soldered directly on the board. August 2022 Revision 03c Page 12 of 15 Kinetic Technologies Confidential Reference Design EVAL Kit MCDP5200 / RD1-5200 Recommended Accessories AC Adapters This list is a list for your convenience. Table 1.Recommended AC Adapter List Application DC5V Input Barrel Plug Manufacturer Model CUI Inc SMI36-5-VP5 USB Type-C Power Adapter Qualtek QFWC-6020-USCR Description Where to Buy 5V/5A 25W https://goo.gl/2VEPF1 AC/DC External Wall Mount Adapter Multi- Blade (Included) Input 5V, 9V, 12V, https://www.digikey.com/short/z4jndz 15V, 20V 60W AC/DC External Wall Mount (Class II) Adapter Fixed Blade Input Cables This is a list for your convenience. As of 2018/9/24, we have confirmed highest data rate with these cables. Table 2. Recommended Cable List Application DP Alt mode Manufacturer Model StarTech.com CDP2DPMM1MB Description Where to Buy USB-C to https://goo.gl/KqGoQZ DisplayPort 4K 60Hz Cable 1m (3.3 ft.) Plugable USBC-DP USB-C to https://goo.gl/Vxta53 DisplayPort Cable 1.8m (6.0 ft.) Cable Matters 201036 USB-C to https://goo.gl/mK9bwi DisplayPort 4K 60Hz Cable, 1m (3.3 ft.) August 2022 Revision 03c Page 13 of 15 Kinetic Technologies Confidential Application USB3.1Gen2 Manufacturer Model StarTech.com USB31AC1M USB31C5C1M USB31CC1M USB31CUB50CM Reference Design EVAL Kit MCDP5200 / RD1-5200 Description USB-A to USB-C Cable - USB-IF Certified USB 3.1 (10Gbps) 1m (3ft) Where to Buy https://goo.gl/2nXNgG USB-C Cable with https://goo.gl/2nXNgG Power Delivery (5A) M/M - USB-IF Certified USB 3.1 (10Gbps) 1m (3ft) USB-C Cable - M/M - https://goo.gl/2nXNgG USB 3.1 (10Gbps) USB-IF Certified 1m (3ft) USB-C to Micro-B Cable - M/M - USB 3.1 (10Gbps) 0.5m (1.6ft) https://goo.gl/2nXNgG August 2022 Revision 03c Page 14 of 15 Kinetic Technologies Confidential Reference Design EVAL Kit MCDP5200 / RD1-5200 Important Notices Legal Notice Copyright © Kinetic Technologies. Other names, brands and trademarks are the property of others. Kinetic Technologies assumes no responsibility or liability for information contained in this document. Kinetic Technologies reserves the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. The information contained herein is believed to be accurate and reliable at the time of printing. Reference Design Policy This document is provided as a design reference and Kinetic Technologies assumes no responsibility or liability for the information contained in this document. Kinetic Technologies reserves the right to make corrections, modifications, enhancements, improvements and other changes to this reference design documentation without notice. Reference designs are created using Kinetic Technologies' published specifications as well as the published specifications of other device manufacturers. This information may not be current at the time the reference design is built. Kinetic Technologies and/or its licensors do not warrant the accuracy or completeness of the specifications or any information contained therein. Kinetic Technologies does not warrant that the designs are production worthy. Customer should completely validate and test the design implementation to confirm the system functionality for the end use application. Kinetic Technologies provides its customers with limited product warranties, according to the standard Kinetic Technologies terms and conditions. For the most current product information visit us at www.kinet-ic.com Life Support Policy LIFE SUPPORT: KINETIC TECHNOLOGIES' PRODUCTS ARE NOT DESIGNED, INTENDED, OR AUTHORIZED FOR USE AS COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. NO WARRANTY, EXPRESS OR IMPLIED, IS MADE FOR THIS USE. AUTHORIZATION FOR SUCH USE SHALL NOT BE GIVEN BY KINETIC TECHNOLOGIES, AND THE PRODUCTS SHALL NOT BE USED IN SUCH DEVICES OR SYSTEMS, EXCEPT UPON THE WRITTEN APPROVAL OF THE PRESIDENT OF KINETIC TECHNOLOGIES FOLLOWING A DETERMINATION BY KINETIC TECHNOLOGIES THAT SUCH USE IS FEASIBLE. SUCH APPROVAL MAY BE WITHHELD FOR ANY OR NO REASON. "Life support devices or systems are devices or systems which (1) are intended for surgical implant into the human body, (2) support or sustain human life, or (3) monitor critical bodily functions including, but not limited to, cardiac, respirator, and neurological functions, and whose failure to perform can be reasonably expected to result in a significant bodily injury to the user A "critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. SUBSTANCE COMPLIANCE Kinetic Technologies IC products are compliant with RoHS, formally known as Directive 2002/95/EC of the European Parliament and of the Council of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. However, this evaluation kit does not fall within the scope of the EU directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and may not meet the requirements of these or related directives. To the best of our knowledge the information is true and correct as of the date of the original publication of the information. Kinetic Technologies bears no responsibility to update such statement. August 2022 Revision 03c Page 15 of 15 Kinetic Technologies Confidential
StarTech.com | IT Pro's Trusted Source for Connectivity Accessories
USB-C CablesSMI36-5-V-P5 CUI Inc. | Power Supplies - External/Internal (Off-Board) | DigiKey3ft USB C to DisplayPort 1.2 Cable 4K60 - USB-C™ Video Adapters | JapanUSB-C to DisplayPort Cable - 8K ReadyPlugable USB 3.1 Type-C to DisplayPort Adapter Cable – Plugable Technologies
QFWC-60-20-USCR Qualtek | Power Supplies - External/Internal (Off-Board) | DigiKey